Showing results: 286 - 300 of 929 items found.
-
HIGHVOLT Prüftechnik Dresden GmbH
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up. Therefore, the test object is designed as a shorted circuit. The high current test system measures the temperature of the test object at various points, in addition to the current. As a special feature, the temperature that the test object should reach can be specified and the amount of the current can be automatically calculated by the HIGHVOLT test system.
-
Extech LCR203 -
Extech Instruments Corporation
The LCR203 are SMD component tweezers for use with Extech's LCR200 LCR meter. These tweezers make it easy to test and sort simultaneously for single handed operation. Tweezers complete the circuit with components easier than separate test leads. Comes with a 6 month warranty.
-
Circuit Check, Inc.
Flash programming stations allow you to offload flash programming from functional test systems, increasing test throughput while improving capital utilization. Circuit Check flash programmer fixtures support multiple programmer types and multiple I/O configurations.
-
TA-400 -
Tech-Aid Products
A Universal ADI Test Panel built to test one of the Astronautics indicators. Panel includes meter drive capability and a specific synchro auto-rate transmitter circuit that allows rates of up to 355 deg/sec. The standard ARINC capabilities make this a universal type tester.
-
Qmax Test Technologies Pvt. Ltd.
Boundary Scan Trainer Kit was developed by Qmax to provide user a good understanding and hands on the testing principals of boundary scan namely the scan chain test, interconnect test, non-BS functional testing of logic IC and cluster like a combinational or sequential circuits.
-
69127 -
Klein Tools, Inc.
Device for checking live 6-24V, AC or DC circuits.Tests for shorts in automotive and truck electrical systems, motor field coils, radio and low-voltage circuits, ground circuit of all lamps, wiring, fuses, etc.Bulb in handle glows when circuit is complete (bulb included).Pointed 3-3/4'' (95 mm) probe makes checking easier.Deluxe 3.5'' (89 mm) long handle with nylon top holds replaceable bulb.36'' (914 mm) test lead with alligator clip.Replacement bulb: Cat. No. 69130
-
EM-6980 | 20 Hz – 50 KHz -
Electro-Metrics Corp.
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
EM-6981 | 9 KHz – 110 MHz -
Electro-Metrics Corp.
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
1653 -
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 24V systems. Use on fuses, test connections and find short circuits quickly and easily. Available for checking on lights, starters, alternators, cooling and heating components, radios and relays.
-
K8214B -
Keysight Technologies
Keysight’s Silicon Nails feature enables all the tools required to develop and execute tests on non-compliant boundary scan devices that are connected to boundary scan compliant devices on the printed circuit board.
-
K8214A -
Keysight Technologies
Keysight’s Silicon Nails feature enables all the tools required to develop and execute tests on non-compliant boundary scan devices that are connected to boundary scan compliant devices on the printed circuit board.
-
AJIT Electronics Co.
This is a common test panel for distribution/ power transformers of different specifications. The user can perform most of the factory tests, as per the relevant IS standard for the transformers. The panel consists of power analyser, meters for high voltage test, meters for induced voltage test etc, control for all the tests, protection and interlock circuits so that a single panel can be used to conduct a number of tests using only one dimmerstat and the associated devices
-
YAVTB000 -
6TL Engineering
When wiring a test fixture, you often have a need to join three or more wires onto the same test point. This module solves this problem, adding test points for manual test probes and a 4 position DIP switch. Circuits 1 and 2 feature up to 5 poles in parallel to increase the space for power supply terminals.
-
BK8015/BK8015A -
BaKo Co., Ltd
The BK8015 HDD Mechanical Specifications Tester and the BK8015A HDD Circuit Specifications Tester were designed and manufactured by BaKo to test HDD motors as they come off the assembly line. The two machines are complementary, and were designed to test a complete set of HDD motor characteristics.
-
Vogelsang & Benning
Series test bench with high testing depth for electric machines in hybrid drive concepts*Single or multi-chamber systems to optimize the cycle time*Testing the no-load and load characteristics*Motor and regenerative test*Short circuit measurement*Noise measurement (NVH)*Temperature measurement