Showing results: 196 - 210 of 929 items found.
-
1152 MF -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
1151 IN -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at Switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-null key.● Test Auto-stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
1155 TMF -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
8022-180 -
VECTOR Electronics and Technology, Inc.
FR4 Hi-Tg, 180°C Material, single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components.Tracks run close to board edges.
-
Technology Products
Primary current injection kits are used to test and commission Circuit Breakers, Bus Bars, CTs, Relays, MCCs, PCCs etc. These are also used for high current injection and simultaneously measuring voltage drops and hot spots in bus-bar joints, Circuit Breaker Contacts etc.
-
2732 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.
-
4132 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.
-
BTS11 -
Elcon International AB
To test circuit breakers in general, is to operate the breaker and check the contact timing. However in factory testing and during field service/maintenance some other tests are necessary. For field testing these other tests can also be very useful in diagnostics purpose.
-
36330 -
S & G Tool Aid Corp
Use to test electronic fuel injection signals, idle air control circuit and spark plug circuits. Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Includes 8 Noid Lights (for checking GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, BOSCH 2 and GM Multec 2; 2 IAC Test Lights (for straight and 90 applications); and Cat. No. 23900, In-line Ignition Spark Checker.
-
LINDY-Elektronik GmbH
This advanced cable tester is ideal for use in computer workshops and repair centres. It allows technicians to test commonly used computer and AV cables. The unit not only identifies open circuits, short circuits and mis-wires it also shows pin to pin connectivity with the ability to record and upload up to 100 test results to a PC. An integrated, backlit LCD provides makes operation straightforward and easy to understand.
-
Test Electronics
Spring Loaded Test Probes for Circuit Board Testing, "Pogo Pins" Test Electronics sources and stockes a large variety of Test Probes and Spring Loaded Test Pins. Let our applications engineers help you find the correct pin for your test fixture application.
-
Semco Machine Corp.
Semco specializes in manufacturing products for the electronic industry. Our Mechanical Test Fixture and CAM-TRAC© Test System Kits provide customers with cost-effective solutions for testing printed circuit boards and assemblies.
-
34133A -
Keysight Technologies
The Keysight 34133A precision electronic test leads are designed specifically for working with small components and dense circuit boards. Each kit includes two test leads (one red and one black).
-
PMK Mess- und Kommunikationstechnik GmbH
It is used to test and measure the current in a circuit. These are simple devices which are coated and colored to indicate positive and negative with the device connector on one end.
-
1673 -
Peaceful Thriving Enterprise Co Ltd
Check on 6-12V systems. Safely test standard primary automotive circuit and on-board computer controlled electrical system without damaging the micro-processor.