Showing results: 946 - 960 of 1072 items found.
-
CZ20074 -
Aegis Pty. Ltd.
The Aegis adjustable sensitivity AC Voltage Detector is the only tool you need to test AC voltage. About the size of a marking pen, this battery operated, non-contact tester detects AC voltages from 50 - 1000V. It's easy to operate, with flashing LED indicators, an audible buzzer and vibration to alert the user when the AC voltage has been detected. The unit will glow green when safe, and when voltage is detected it will flash red and beep at an increasing rate as you get closer to the voltage source.
-
KRD41 series -
CME Technology Co. Ltd.
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
LUCID Triton -
ViTec Co. Ltd
Industrial GigE cameras;Protection class IP67;Dust and water resistant;Vibration and shock resistance;Wide operating temperature range (from -20 to +50);Sony II, II and IV generations sensors from 0.4 to 24.5 megapixels;Linear camera Triton Line Scan 2k 60 kHz Model;Polarization models Triton 5.0 MP Polarization Model ;HDR model Triton 5.4 MP Model ;C-mount;Connectors: M8 / M12;Dimensions: 29x29 mm;Weight: 67g;Price: from 365 $.
-
FLIR VP50-2 -
Teledyne FLIR
The FLIR VP50-2 is a durable, CAT IV-rated non-contact voltage detector featuring light, vibration, and beeper feedback alarms and a powerful LED flashlight. Use the VP50-2 to reliably check if an AC circuit is live before beginning work; detect voltage on exposed conducting parts or through insulation; identify live wires within electrical panels, switches, and outlets; or trace live wires and map circuits. With an ergonomic and drop-tested design, the FLIR VP50-2 is the right choice for professionals performing field troubleshooting and verification of electrical installations within residential, commercial, and industrial buildings.
-
CP68301 -
LinkedHope Intelligent Technologies Co.,Ltd.
CP68301 meets PICMG2.16 specifications, mainly used for high speed data exchange between the board and the routing to the internal CPCI, ATR case. The CPCI structure of the module uses the standard 6U, and can be compatible with the ATR structure design. Heat dissipating performance and unique environmental protection design of anti - vibration design, reliable and excellent. The module integrates switching and routing functions, with 24 10/100/1000M adaptive Ethernet interface, satisfy the chassis and external data transmission, realize the comprehensive integrated, modular, easy maintenance use, improve equipment reliability and application.
-
Bowmonk Ltd.
The Brakemeter / Dynometer is a hand-made precision instrument that mechanically measures both deceleration and acceleration. The instrument consists of a finely balanced pendulum, free to respond to any changes in speed or angle, working through a quadrant gear train to rotate a needle round the dial. The dial is black with silver white graduations and has a linear length of 5 1/2 inches (114 mm). The unit is filled with a special fluid which damps out all vibration. Other than a calibration every 2 years, which is carried out by Bowmonk, no maintenance is necessary.
-
Dongguan Amade Instruments Technology Co., Ltd
Lithium battery test chambers are used to simulate various extreme conditions such as crush, impact, penetration, overcharge etc the lithium ion cells and batteries are subjected to during use, transportation, storage and disposal to determine the safety performances, tests including altitude simulation test, thermal test, vibration test, shock test, external short circuit test, impact/crush test, overcharge test, discharge test etc based on UN38.3, IEC62133, UL1642 standards. Applicable to communication products, computer products, consumer electronics, automobile power supplies and so on.
-
OBS-ONE series -
HORIBA, Ltd.
HORIBA developed the OBS-ONE series on-board emission measurement system in response to new requirements for exhaust emissions measurement from vehicles being driven on public roads (Portable Emissions Measurement Systems - PEMS). This development has been made possible by reducing the dimensions and power consumption of laboratory grade analyzers and ensuring that the system components have excellent vibration resistance. The OBS-ONE series continuously measures not only the concentration of CO, CO2, THC and NOx, but also measures exhaust fl ow rate and A/F ratio to calculate mass emission and fuel economy.
-
BK2028/BK2028A -
BaKo Co., Ltd
We designed the BK2028 and BK2028A Piezo Unit Aging Testers for you to test your piezo electric vibration units for long term reliability. The BK2028 can test up to 50 units at a time, while the smaller BK2028A tests 20. Both models are easy to set up and can be stacked. They allow you to control the number of tests you you run so that you can run a large number of DUT's under exact conditions and make sure your piezo units will do what you expect them to do for the life of your products.
-
Teledyne Defense Electronics
Teledyne Advanced Electronic Solutions performs comprehensive testing at the CCA and system level assembly. Teledyne AES can perform testing developed by the customer or develop a complete test strategy for the customer’s products.- Bed of Nails FixtureIn-Circuit Test (Bed of Nails) or Flying Probe Testing for rapid feedback on CCAs- Functional testing of CCAs or complete systems- Environmental testing to include vibration, thermal cycling, HASS, etc.- CCA and system level test development- High frequency testing – currently to 40 GHz- High power system testing – currently to 4kW
-
783906-01 -
NI
4-Channel, SPST Relay, 60 VDC (1 A)/250 VAC (1.5 A) C Series Relay Output Module - The NI‑9482 directly connects to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to an electromechanical relay for switching signals up to 60 VDC (1 A) or 250 Vrms (1.5 A), features channel‑to‑channel isolation, and has a LED that indicates the status. The shock and vibration rating for the NI‑9482 is limited compared with other CompactDAQ and CompactRIO modules because of the mechanical relays on the module.
-
Crystal instruments
Automated production testing is critical in today’s competitive manufacturing environment. Companies can no longer rely on variable costs, non-uniformity, and potential health hazards that come with a laborer-based manufacturing line. This is no less true for sound and vibration tests, ranging from in-process burn-in tests to product validation and verification tests. The measurement tools and intelligence behind present day manufacturing include data acquisition equipment as well as closed-loop control. And while these systems may not take part in the assembly of any goods, they are just as important to ensure quality control for both components coming into an assembly line and products going out.
-
HM500 LIGHT -
Helmut Fischer AG
Very simple operationExcellent price/performance ratio: The achieved resolution and accuracy for the load and distance measurement is in the same range as that of instruments with a much higher purchasing priceMinimal sample preparation due to large working area and open layoutMeasurements on dark surfaces without sample preparationFor simple specimen's geometries sufficient positioning accuracy of 2 mDue to its granite design, the device is extremely dimensionally stable, has a very low thermal expansion and is excellently isolated against vibrations.Additional vibration damping through closed measuring chamber and active anti-vibration tableEasy operation through the customizable WIN-HCU Software
-
BK8612 -
BaKo Co., Ltd
We designed the BK8612 2 Channel Noise Test System to provide noise and vibration testing for your digital camera barrel DC Motors. Because it is based on the BaKo BK2120B DAQ, it is capable of monitoring a microphone and an accelerometer concurrently to obtain data from the motor. Because you can change the parameters of functions and limits, it is versatile but still quick and easy to set up. In addition, you can look at data in real time and also store it for future analysis. Easy to use and set up, fast and accurate; if you need to maintain the quality of your camera barrel motors, this is the tester you want.
-
ADLINK Technology Inc.
ADLINK products include the most rugged offerings in the industry, Single Board Computers (SBC) in popular compact form factors for embedded applications, and rugged systems with field-proven reliability, durability, and performance. PC/104 family products provide unmatched fanless operation over temperature extremes, resistance to shock and vibration, conformal coating, embedded BIOS, and a long product life reputation. The products continue to distinguish itself as an Extreme Rugged product for a multitude of applications. Mini-ITX embedded boards support the latest processors to deliver a high performance and space-saving platform for a wide array of embedded computing applications.
