Showing results: 556 - 568 of 568 items found.
-
781421-11 -
NI
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
42-411A-001 -
Pickering Interfaces Ltd.
The 40-411A-001 (PXI) and 42-411A-001 (PXIe) are 64-channel relay drivers and are part of a range of modules with 16, 32, 48 or 64 channels of low side current drive. To use the module, simply connect a positive voltage source to one side of the relay coil and the other side to an output channel. Each output is capable of sinking up to 1 A of continuous current.
-
40-411A-001 -
Pickering Interfaces Ltd.
The 40-411A-001 (PXI) and 42-411A-001 (PXIe) are 64-channel relay drivers and are part of a range of modules with 16, 32, 48 or 64 channels of low side current drive. To use the module, simply connect a positive voltage source to one side of the relay coil and the other side to an output channel. Each output is capable of sinking up to 1 A of continuous current.
-
VME-2232A -
Abaco Systems Inc
VME-2232A is a 32-Channel Relay Output Board with Built-in-Test (BIT). Software compatible with the VMIVME-2232 and the VMIVME-2533.
-
Megger Group Ltd.
Megger’s single phase relay test sets are essential items in the relay engineer’s toolbox. Lightweight, rugged with high compliance voltage and test current. Ideal for testing distribution networks, industrial relays, distance relays in rail power networks and many other applications.
-
PACB108 -
Ponovo Power Co., Ltd.
PACB08 is the accessory device to perform the energy meter test, which can work together with PONOVO’s relay test sets to test energy meter by using Energy Meter Module in Powertest software.
-
RXB1 -
OMICRON electronics
RXB1 extends CMC test sets with 4 additional binary relay outputs. Each binary output channel consists of a normally open ("make") and a normally closed ("break") contact.
-
Ponovo Power Co., Ltd.
As the first protection relay test set manufacturer in China, PONOVO has been always offering reliable protection relay testing equipment for customer for more than 20 years. More than 20,000 relay test kits has been supplied to users in China and other countries, including 6-phase, 3-phase, single phase relay test sets, capable of testing all kinds of protection relays, from electromagnetic relays, solid state, numerical, microcomputer relays and digital relays based on IEC61850 as well as other testings, such as, energy meter, transducer, etc. With various models with different specifications, users can definitely choose the model suitable for their testings.
-
T&R Test Equipment Ltd.
Our primary current injection test sets cover from 750A through to 6000A. Available in single phase, testing applications include testing and timing of under and over current relays, circuit breakers and CT ratio testing.
-
SUBNET SEL -
SUBNET Solutions Inc.
SUBNET SEL Relay Data Emulator Software can automatically learn a SEL relay’s communication capabilities. SUBNET SELRDE Software can then be directly substituted for the physical SEL relay to safely and reliably commission relay communications. Effortlessly change target and meter data through SUBNET SELRDE Software without the inconvenience or risk of physically jumpering contacts or using expensive and often unavailable test sets to directly inject voltage/current.
-
R.R.Transformers & Equipments
Protective devices such as relays, overload Coils, Circuit breakers and CTS etc. must be checked regularly to ensure that they are always ready to operate correctly, Routine current injection testing will quickly detect faulty or incorrectly adjusted protection circuits / devices & will be possible to prevent serious damage to the system. Primary injection kit is designed to operate on single phase 230/240 volts AC 50 HZ to develop smooth & continuous test current as for loading, calibrating, and testing of CTS, Bimetal Relays, Protection Relays etc. The test set gives high current output at low cost and with inherent safety. The primary current injection testing checks all parts of the protection system by injecting current down the cable / bus bars. The application of the primary current injection sets is to ascertain the current carrying capacity of any Conductor, insulator, connector or calibration of CTS / Bi-metallic relays etc.
-
Extech 380363 -
Extech Instruments Corporation
This Extech insulation tester measures up to 10GΩ with 250V, 500V and 1000V Test Voltages. Features include: Lo-Ohms for testing connections, analog bargraph for viewing trends, AC/DC Voltage measurement to 999V, manual data record/recall function (9 sets), and live circuit display warning and beeper. Can be used to test motor, transformer windings, instruments, and appliances, check for moisture in wire and cable assemblies, safely evaluate a new wiring installation, and check for carbon tracking in breakers, relays, and switches. Extech Insulation Testers offer high sensitivity to assure reliable monitoring of low resistance motor windings. Complete with carrying case, test leads, and 6 x AA batteries.
-
LEDRACK-100W192P -
Lisun Electronics Inc.
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)