Filter Results By:
Products
Applications
Manufacturers
Breakout Boxes
reroute signal paths to facilitate contact accessability.
See Also: Boxes, Breakouts, Decade Box, Anechoic Boxes, Black Box, Hot Box, White Box, Shielded Box, RF Box, Programmable Resistance Box
- Pickering Interfaces Inc.
product
Modular Breakout System Chassis Mounting Frame
95-901-001
The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications. This low-cost system combines a BoB (Breakout Box) feature set with the added flexibility of an FIU (Fault Insertion Unit). By mating the FIU chassis directly to the BoB, cabling is minimized, creating a more compact reliable design and improving signal integrity.
-
product
Breakout Box for Easy Access to PXI-501 Functions
PXI-501 ACS-001
The PXI-501 ACS-001 is an extension for the PXI-501. It provides 4mm sockets do directly connect a DUT to the PXI-501 source and measurement functionallity. It’s especially recommended for laboratory environments and debugging purpose.
-
product
Breakout Module
PXI-PDM
The PXI Preamplifier Power and Trigger Breakout Module (PXI PDM) is an accessory for the Pixie-4 system.
-
product
Custom Breakout Boxes
Silver Engineering, Inc. has also provided many different forms of custom breakout boxes and adaptor cables to our customers. If you need something special, contact us.
-
product
Fifo Serial Analyzer 2 TO 1 Breakout Boxes
FLL221/FLL221S
The FLL221 BreakOut Box is designed to be used with the FLL and FSA serial analyzers when they run on PC's with only one ComPort. The serial line passes through FLL221 using the 9-pin connectors. Data from both pin 2 and 3 of the serial line is available on the FLL221 output. The output cable from FLL221 is connected to the ComPort of the PC running the analyzer.
-
product
Fifo Serial Analyzer 2 TO 2 Breakout Box
FLL222
The FLL222 Break Out Box is designed to be used with the FLL and FSA serial analyzers to monitor full duplex bidirectional data. The serial line passes through FLL222 using the 9-pin connectors on the unit. Data from pin 2 of the serial line is available on pin 2 in the first output cable. Pin 3 data is available on pin 2 of the second cable. The output cables can be plugged into the COM ports of the PC running the serial analyzer.
-
product
Fifo Serial Analyzer Breakout Box
FLLBOB
FLL BreakOut Box FLLBOB is a breakout box specially designed to be used with the FLL and FSA serial analyzers. With FLLBOB it is easy to connect the PC to the serial line without having to make dedicated cables.
-
product
(ITA), Breakout Box & Fixtures
WinSoft provides a wide range of Interface Test Adapters (ITA) and test fixtures to meet the most challenging functional test and signal conditioning requirements. This includes high frequencies, voltages and current.
-
product
Serial Breakout Box Software
Turn any PC or Laptop with two serial ports into a serial breakout box (serial line analyzer). Snoop in on data that is sent or received through an RS232 serial cable between any two devices or computers. This is an excellent tool for diagnosing serial communications problems as well as for figuring out what is being sent and received between two devices.
-
product
OBD-II Breakout Box
PPECB
The Power Probe OBD-II Breakout Box is a CAN Bus circuit tester compatible with 12 and 24 Volt systems. The tool connects directly into the Vehicle’s Data Link Connector (DLC) testing for any abnormalities such as shorting and reverse polarity at the pins. If shorting or reverse polarity is present, connecting the PPECB first will prevent harm before connecting a Diagnostic Scan Tool. The Breakout Box provides a live display of present communicating signals without having to use a Digital Multimeter. Additionally, you can quickly test the voltages at all 16 pins.
-
product
Breakout Box
T1000-62HD
Our most expansive breakout box, using dual High Density 62 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 124 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity.
-
product
Breakout Box
FV-EXT
The handy FiberVision devices FV-EXT1 and FV-EXT2 are designed for the easy integration of FiberVision and Vision Component (VC) smart cameras into your production environment.Central interface for all supply- and communication-cables (switch board)Remote control for all VC based smart cameras such as Caminax or PictorTest of digital camera I/Os and the production environment
-
product
Breakout Boxes
D Series
The D Series Breakout Boxes incorporate a printed circuit board for all connectivity. D Series Breakout Boxes use a color coding scheme as an aid. The Red jacks connect to the Red TP Side connector with pin contacts and the Black jacks connect to the Black TP Side connector with socket contacts.
-
product
Camera Link Breakout Box
CLB-501B
The CLB-501B Camera Link Breakout Box provides convenient access to the data transferred between camera and frame grabber over a Camera Link connection. All video, control, and communication data can be monitored and/or sourced via a standard header connector located on the rear panel.
-
product
Breakout Box
T1000-9
T1000-9 breakout box is our most compact breakout box, using dual 9 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 18 test points plus a ground jack. All test points use standard size 4mm banana jacks. Ideal for continuity testing, isolation testing or signal capture and monitoring.
-
product
Breakout Box
T1000-37
T1000-37 breakout box is our most versatile model, using dual 37 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 74 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
product
Accessories: Test Hardware
Copernicus Technology supply test hardware accessories to support Intermittent Fault Detection testing using VIFD™ and IFDIS™ test equipment, such as Interface Test Adapters (ITA). We also supply and repair general purpose and customer-spec test hardware accessories: ITAs, Break-Out Boxes (shown below) and Mobile Vibration Systems. The Mobile Vibration System can be quickly set up in repair bays for applying environmental stimulus to components and wiring harnesses during testing.
-
product
Breakout Box
T1000-15
T1000-15 breakout box with dual 15 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 30 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
product
OBD Protocol Diagnostics
Our innovative OBD Protocol Diagnostics comes with diagnostic break-out boxes and CAN network testers which can expedite maintenance, and streamline the troubleshooting process at the system, subsystem, and component-level by simplifying the access to test ECU signals.
-
product
Connector and Breakout Box
ES4640
The ES4640 Connector Box offers a standardized wiring and connectivity for HiL testing systems in the powertrain domain. Its front panel provides connectors for the ECU, CAN bus communication, on-board diagnostics, and LEDs for ignition and injectors. Its rear panel connects loads, failure simulation, and other components. Sample applications of the ES4640 are closed loop HiL systems for 8 cylinder gasoline and diesel engine ECUs.
-
product
Pitot Static Breakout Box (PSBB)
C-17
The C-17 Pitot Static Breakout Box is a derivative of TestVonics™ Line Switching Unit (LSU) Series. The assembly includes a multi-port distribution unit which provides 4 Pitot and 8 Static outputs from one channel of Pitot and Static controlled pressure. The LSU distributes pitot static supplies for the external services and connection of hose assemblies for testing of aircraft Pitot and Static ports for the C-17. The lightweight unit is housed in a highly durable and easy to maneuver case. Additionally, four (4) 30ft Pitot Hoses, eight (8) 30ft Static hoses, and two hose storage bags are included with the assembly.
-
product
OBD II Data Link Connector Breakout Box & Diagnostics Software
Mr. BOB DLC
Automotive Diagnostics and Publishing
Mr. BOB DLC OBD II Data Link Connector Breakout Box & Diagnostics Software for Network Waveform Viewing. This OBD2 breakout box with 8 Graphing Meter Scope like channels, is designed for the OBD2 DLC data link connector. Includes OBD II protocols such as PWM, ISO, KWP2000, 9151, J1850, VPW and CAN.
-
product
Breakout Tools
Quickly test and troubleshoot harnesses, engine control modules or sensors by connecting a Breakout Box onto your system.
-
product
Measurement System for ESD Protection
SampleProtect
The SampleProtect measurement system is ready to go, and comes complete with Oxford Instruments’ Cryofree bottom loading cryostat – the OptistatDry BLV, Zurich Instruments’ MFLI Lock-in Amplifier, a specially designed ESD break-out box and high quality measurement grade cables. The patent-pending puck style mounting from Oxford Instruments provides safe installation of your samples. The MFLI 500 kHz Lock-in Amplifier (capable of 500 kHz demodulation as standard) with MF-MD multi-demodulator capability brings the benefits of high performance signal processing at low and medium frequencies. The differential voltage and current inputs of the MFLI are optimised for low noise operation and the high oversampling rate ensures an even better signal to noise ratio. Zurich Instruments’ unique LabOne® control software provides a toolset including an integrated oscilloscope, a spectrum analyser, a plotter and a parameter sweeper.
-
product
Multiport Serial Adapter, PCIe X4
PCI325
The PCI325 is an RS-422 synchronous/asynchronous multiport serial adapter. The module can accept a clock input to synchronize the baud rate generators of each port to an external clock. All the protocol management overhead is taken care of in the hardware so that the host CPU is offloaded from managing the detailed serial protocol. An I/O breakout box may be connected to the high-density connectors of the PCI325 to provide multiple DB25, DB9, or other serial connectors for easy integration to your system or an octopus-style breakout cable may be used. The I/O breakout box may include many different status LEDs which can be tailored to your protocol/application. The PCI325 provides the breakout box with power so that it does not require any additional power cabling
-
-
product
Breakout Box and Data Logger
1U643-001
The 1U634 Breakout Box and Data Logger was developed for the Cessna Excel to serve as the main diagnostics tool for the aircraft?? electronic modules. It allows access to the module pins, and its internal microcomputer digitizes the signals and transmits them to a PC-compatible computer. Advanced software in the computer displays pin voltages either in numerical or graphical form. Data files can be recorded on disk, and played back at a later time for detailed analysis.
-
product
EMX-4XXX Product Family
The EMX-4xxx product family contains high-performance breakout boxes (EMX-4008 and EMX-4016), smart high density dynamic signal analyzers (EMX-4250 and EMX-4251), smart PXIe 625 KSA/s 4-channel digizers (EMX-4350), and charge and IEPE PXIe 625 KSA/s 4-channel digitizers (EMX-4380).
-
product
Breakout Box
A piece of electrical test equipment used to support integration testing, expedite maintenance, and streamline the troubleshooting process at the system, subsystem, and component-level by simplifying the access to test signals
-
product
"Smart" Dynamic Signal Analyzers
EMX-4xxx
The EMX-4xxx product family contains high-performance breakout boxes (EMX-4008 and EMX-4016), smart high density dynamic signal analyzers (EMX-4250 and EMX-4251), smart PXIe 625 KSA/s 4-channel digizers (EMX-4350), and charge and IEPE PXIe 625 KSA/s 4-channel digitizers (EMX-4380).
-
product
NI CAN Cable, No Term, High-Speed/FD/Low-Speed, D-Sub 9-Pin F, 1m
193128-01
9-Pin Female D-SUB to 9-Pin Female D-SUB CAN Cable - The DB9F-DB9F CAN Cable connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules to devices, breakout boxes, and accessories. It is sometimes referred to as CAN Cable (single termination or no termination). This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals, available with or without termination, and in different lengths.
