Showing results: 4486 - 4500 of 5965 items found.
-
Avionics Interface Technologies
Support for up to 30 Network Interfaces (Fibre Channel & Ethernet)Time Synchronization with IRIG-B & IEEE 1588 Master ClocksFull Data Capture with time stampingData simulation with precise timing & synchronizationNetwork data replay from previously captured trafficPerform Network analysis using AIT's intuitive, easy to use, Ethernet & Fibre Channel simulation tools
-
D&V Electronics LTD
D&V’s diode and rectifier test systems provide a quick, accurate and easy to use interface to check and measure all main parameters of regular and avalanche rectifiers. Real life conditions are simulated to maximize diagnostic capabilities. Additionally, analysis of the rectifier’s thermal resistance can be performed to detect poor internal diode connections and related defects.
-
SMC Sentry IT -
MSA
The SMC Sentry IT Controller is a powerful network-enabled hazardous gas detection system that operates up to 32 detectors and interfaces with devices over Modbus RTU, 4-20 mA, Sentry PSG Bus, and conventional dry contact. The embedded web application enables users to view important data remotely and provides connectivity into the Industrial Internet of Things (IIoT).
-
Sherlock-300I -
Manncorp
Add PCB inspection to your automated production line, pre- or post-reflow, and speed up your process. Inline Sherlock 300I AOI system inspects components and solder joints on SMT, through-hole and mixed-technology boards and communicates with downstream equipment for automatic good/bad board sorting. The user interface is 100% touch control—as easy to use as a tablet.
-
MCH-2817 -
MCH Instruments Co.,Ltd.
Is a high accuracy, wide measuring range impedance tester. With test frequency upto 100kHz, three test signal levels and capacity of measuring parameters such as Resistance(R), Capacitance(C), Inductance(L) and etc. It's equipped with a 240 × 128 dot , back-lighted LCD display which provides user friendly interface for measurement and operation.
-
YAVHF3X4C50 -
6TL Engineering
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
YAVHF3X4C -
6TL Engineering
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
YAVHF3X4 -
6TL Engineering
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
9200 Series -
NH Research, Inc.
12 to 144kW with either 120 or 600 V Power Modules Fast voltage, current and mode transition times Digital measurement system with hi-res waveform capture and digital chart recorder Custom waveform/profile generation Multiple safety features to protect battery Touch-panel manual interface Customer's own or NHR Enerchron™ Test Executives
-
JT 5705 -
JTAG Technologies Inc.
The JT 5705 series offer a unique combination of JTAG TAP controller (tester) interfaces plus digital and analog I/O in compact desktop package.Use the ‘mixed-signal’ features to measure power supplies, clock frequencies or test DACs and ADCs. Add your own capability through use of CoreCommander FPGA our generic bridge/translator system.
-
CPCI-6713-4 IP -
ALPHI Technology Corporation
The board consists of private SDRAM and Flash memory attached to the 300 MHz TMS320C6713B DSP. An FPGA provides the timing and control. Peripherals include a serial port and connectors for IP mezzanine boards. Flash memory is availablefor downloading programs into a non-volatile memory. A PCIbus connector provides the interface to the host computer. A serial port is available for debugging.
-
GT98901 -
Terotest Systems Ltd.
The GXT98901 Demo board is a USB controlled, cost-effective, multi-function PCB assembly. The module is completely self-contained and includes an LCD display, measurement and stimulus resources, digital I/O, relays, and switches – all which can be accessed and monitored via the USB port using a SCPI command set via a USBTMC interface which supports the USB488 protocol.
-
Signal Processing - DX -
APEX Turbine Testing Technologies
DX is an easy to use, graphical, signal processing environment that simplifies analysis and reporting of dynamic data. DX includes everything needed to process data for a variety of applications and industries in a very intuitive, drag-and-drop user interface. Generate fully-interactive engineering plots from one or more tests and create reports in just a few mouse clicks.
-
cPCIS-2642 Series -
ADLINK Technology Inc.
*Dual 3U CompactPCI® Systems, each with five peripheral card slots and one system slot*1/1 250 W CompactPCI® Power supplies*Temperature, voltage, and fan monitoring LEDs*Supports current sharing on +5 V, +3.3 V, and +12 V*PICMG® 2.11 47-pin power interface
-
SDI-1 -
FM SYSTEMS, INC.
The SDI MASTER is a digital, hand-held, battery operated meter that measures six characteristics of High Definition and Standard Definition digital television signals. Use it for fast and accurate set-up and verification of levels, slope-loss and return loss on any SDI (Serial Digital Interface) Digital Television Signal. This meter is a must have for anybody working with digital TV.