Showing results: 976 - 990 of 5965 items found.
-
Emutel Duo -
Arcatech Limited
Emutel Duo is a convenient and flexbile basic rate and primary rate ISDN network simulator. With 3 software selectable S/U interfaces and optional 2 E1/T1 interfaces you can test and develop a full range of ISDN equipment.
-
Avionics Interface Technologies
AIT's Shared Memory Network (SMN) interface modules provide host systems with an interface to a high speed (2.125 Gbps) optical data network which can be used to share data, in real-time, between multiple distributed systems.
-
MS 1712 -
Meltronics Systemtech
- 12 Channel RS422 Standard Communication interface- 4 Channel Configurable Manchester Bi-Phase Signal communications- 4MBPS configurable baud rate- VIRTEX4 FPGA based design- Hardware Frame formation- Hardware Data validation with START & END frame identification and Checksum calculation for RS422 communication- 1MB DPRAM for PCI interface- Separate set of FIFO's for Transmit and Receive channel- 16 Channels data recording through CF (Compact Flash Storage - Capacity up to 8Gbyte) up to 30min @ 2Mb/sec- Online download through USB interface- Driver interface for Windows2000/XP/VISTA and LINUX OS- 6U size cPCI Board- Hot Swap facility is provided for the live Insertion and removing of the board- 12 RS422 channels in front panel interface using two 25-pin D-Type connector
-
782578-01 -
NI
9-Pin Female D-SUB With 2-Pin Female Power Screw Terminal to 9-Pin Female D-SUB CAN Cable - The DB9F-PT2F-DB9F CAN Cable, sometimes referred to as CAN Cable (with power terminals), connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotoco Interface Modules that have ports requiring external power with external CAN signals. The screw terminals on the cable allow for the direct wiring of power and ground to the port on the CAN interface. This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals and is available with or without termination.
-
782579-02 -
NI
9-Pin Female D-SUB With 2-Pin Female Power Screw Terminal to 9-Pin Female D-SUB CAN Cable - The DB9F-PT2F-DB9F CAN Cable, sometimes referred to as CAN Cable (with power terminals), connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules that have ports requiring external power with external CAN signals. The screw terminals on the cable allow for the direct wiring of power and ground to the port on the CAN interface. This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals and is available with or without termination.
-
782578-02 -
NI
9-Pin Female D-SUB With 2-Pin Female Power Screw Terminal to 9-Pin Female D-SUB CAN Cable - The DB9F-PT2F-DB9F CAN Cable, sometimes referred to as CAN Cable (with power terminals), connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules that have ports requiring external power with external CAN signals. The screw terminals on the cable allow for the direct wiring of power and ground to the port on the CAN interface. This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals and is available with or without termination.
-
MS 3633I -
Meltronics Systemtech
CPCI Rear IO Analog Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on all type of Analog input and output interface including signal conditioning from ACIO board to Rear IO interface. Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
PGY-I3C-EX-PD -
Prodigy Technovations Pvt. Ltd.
I3C Protocol Analyzer (PGY-I3C-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. I3C Serial bus interface is emerging as a chosen interface for all future sensor connectivity in mobile phone and automotive Industry. This could also be chosen for low cost, reliable interface for future embedded electronic applications to address the new data intensive applications.
-
UPM STM32F429 -
Holding Informtest
The universal processor module UPM STM32F429 is intended for use as part of devices developed by the user and for providing control of these devices via various control interfaces and for ensuring the interaction of these devices with a PC via the Ethernet or USB 2.0 HS interface.
-
H73000301 -
6TL Engineering
This module, named “6TL-MMI Lite version”, is designed to be the interface between an operator and a SYSTEM as well as being a metered power distribution unit (PDU) for it. The module is providing also safety controls, data bus interfaces, temperature control and timers.
-
Microchip Technology Inc.
Enhance your product’s user interface by replacing mechanical push buttons with a touch- or gesture-controlled interface. This is an excellent way to add value and advanced features to your application, increase customer appeal and improve your product’s performance and reliability.
-
Kualitatem Inc.
Usability Testing generally includes testing user interface (UI) and user experience (UX). One is about testing your Graphical User Interface and how it looks & behaves, while the other focuses on user experience and user behavior.
-
cPS-H325/AC -
ADLINK Technology Inc.
*PICMG® 2.11 CompactPCI® Power Interface compliant*3U CompactPCI® 8HP form factor*PICMG® 2.11 47-pin CompactPCI® in-rack power module interface*250 W DC output
-
cPS-H640/AC -
ADLINK Technology Inc.
*PICMG® 2.11 CompactPCI® Power Interface compliant*6U CompactPCI® 8HP form factor*PICMG® 2.11 47-pin CompactPCI® in-rack power module interface*400 W DC output
-
cPS-H325/24 -
ADLINK Technology Inc.
*PICMG® 2.11 CompactPCI® Power Interface compliant*3U CompactPCI® 8HP form factor*PICMG® 2.11 47-pin CompactPCI® in-rack power module interface*250 W DC output