Showing results: 106 - 120 of 587 items found.
-
-
TPP -
Mess- & Prüfsysteme GmbH
The Partial Discharge Test System type TPP is used for non-destructive insulation and quality testing of electrical components (for example according VDE 0110-1, EN 50178, IEC 60270 and IEC 60060).
-
Rigel 288 -
Seward Medical
The Rigel 288 is the FIRST universal truly hand-held medical electrical safety tester to combine the features of an automatic / manual tester with a data logging / asset management facility. In addition to IEC 60601-1 and AAMI / NFPA 99, the Rigel 288 tests to the new standard for in-service and after repair testing of medical electronic devices, currently drafted in as the IEC 62353.
-
CX-A3C -
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts by use of a tool through holes which give access to pre-set controls. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN 61010-1, U- 3101-1, UL 3111-1 and CSA 1010-1. The handle and stop face are made of Delrin®. The rod is stainless steel.
-
-
11A131-6 -
ELMA Electronic, Inc.
Shielded subracks for IEC applications. EMC subrack made of sheet steel for extremely fast mounting and EMC without seals.
-
11A132-6 -
ELMA Electronic, Inc.
Shielded subracks for IEC applications. EMC subrack made of sheet steel for extremely fast mounting and EMC without seals.
-
11A133-7 -
ELMA Electronic, Inc.
Shielded subracks for IEC applications. EMC subrack made of sheet steel for extremely fast mounting and EMC without seals.
-
11A133-6 -
ELMA Electronic, Inc.
Shielded subracks for IEC applications. EMC subrack made of sheet steel for extremely fast mounting and EMC without seals.
-
11A162-6 -
ELMA Electronic, Inc.
Shielded subracks for IEC applications. EMC subrack made of sheet steel for extremely fast mounting and EMC without seals.
-
IS-*MT -
Lisun Electronics Inc.
According to requirement of IEC standards, the standard test temperature is 25℃, but high power lamps such as HID lamps and LED outdoor luminaires will produce a lot of heat during the test, thus the temperature inside the integrating sphere can not meet the requirements of IEC standards. Lisun Group designed the Constant Temperatured Integrating Sphere which allows the lamp was tested in a constant air temperature.
-
PROFINET -
Anybus
PROFINET is the innovative open standard for Industrial Ethernet, development by Siemens and the Profibus User Organization (PNO). With PROFINET, solutions can be implemented for factory and process automation, for safety applications, and for the entire range of drive technology right up to clock-synchronized motion control. PROFINET is standardized in IEC 61158 and IEC 61784. Profinet products are certified by the PNO user organization, guaranteeing worldwide compatibility.
-
PAS-Products
PAS Multi Meter Bridge can be configured in a number of different ways, to accurately model the ballistics, responses and graphics of a wide range of standard peak programme meters. These meters currently include the following:*IEC 268-10 Type I (Nordic N9 meter)*IEC268-10 Type IIb (EBU PPM meter)*IEC 268-10 Type IIa (BBC PPM meter)*DIN 45406
-
Arden Photonics LTD
*Improve measurement accuracy*Ensure stable launch conditions for multimode fiber measurements*Meet EF requirements of IEC 61280-4-1.
-
Arden Photonics LTD
*Improve measurement accuracy*Ensure stable launch conditions for multimode fiber measurements*Meet EF requirements of IEC 61280-4-1.