Showing results: 271 - 285 of 445 items found.
-
DER EE Electrical Instrument
The hall effect sensor products are manufactured according to international standards. Being an ISO 9001:2008, ISO 14001 and OHSAS 18001 certified company, DER EE is capable of designing and producing superior products to the highest standards of customers' requirements. Hall effect sensors we provided are a device containing both the sensor which produces a very low signal level and contains the vacuum tube amplifier and a high gain integrated circuit (IC) amplifier in a single package. hall effect sensor offer many applications to sense position and motion, to control electric motor control, to sense wheel rotation and so on.
-
Schwarzbeck Mess Elektronik
Active Receiving Loop Antennais an active shielded handheld loop antenna with nearly constant antenna factor over the entire frequency range. It can be used for testing acording to CISPR, MIL, FCC, EN, ISO, ANSI, ETSI and many other standards.
-
NovoTest
Concrete Cover Meter NOVOTEST Rebar Detector (rebar locator) is designed in accordance to EN 12504-4, ASTM C597-02, ISO 1920-7:2004, IS13311, CECS 21 standards and is intended for operational monitoring of reinforced (searching rebars inside building structures) concrete products and structures for process control in the factories and building sites, surveys buildings and structures. The device measures the protective layer of concrete by magnetic method.
-
EKT-100H -
Ektron Tek Co., Ltd.
Designed and manufactured in accordance with ASTM D2048& ISO 6502 standards. Output, displayed and memorized graphics including Elastic torque, Cure rate, and Upper/Lower dies temperatures. More than 30 items of data, such as ML, MH, TS, TC, CRI etc., couble be taken from each test. Cure curve provides the processing, vulcanizing, and vulcanized physical properties of rubber cross-linking reaction.
-
Gamma Scientific Inc.
Gamma Scientific is ISO/IEC 17025 accredited by NVLAP (NVLAP lab code 200823-0). In addition to assurance of measurement accuracy, accreditation ensures traceability to known standards, provides international acceptance of measured values, and is important for compliance purposes for your own ISO/IEC certifications. Our state-of-the-art, ISO 17025 accredited calibration laboratories in San Diego, California offer a range of test and calibration services including:
-
JYUE LII INTERNATIONAL CO., LTD.
A&V power transformer supplies and manufactures certified switching power charger with industrial UL / cULus / CB / CE / TUV & ISO 9001:14001 certified electrical products and manufacturing facilities based in Taiwan. Switching Power Charger Includes C02 Series, C05 Series, C06 Series, OP Series, C07 Series, C08 Series, MDA Series, LN Series Switching Power Charger
-
Circuit Assembly Corp.
High quality connectors are just the beginning. Circuit Assembly (CA) also has over three decades of experience in producing a wide variety of cable assemblies for various applications. CA has the technical and manufacturing capabilities to provide customers with high-quality and cost-effective cable assemblies tailored to meet their needs. Circuit Assembly utilizes a quality process recognized by ISO 9001, and CA's cable assemblies are UL/CSA certified.
-
FIME SAS
FIME laboratory equipment qualified for RF testingValidate the analogue behaviour of RF devices with a single set of laboratory tools and services before seeking contactless Level 1 type approval or launching mass production. FIME RF test benches are built for RF testing of: EMV contactless cards and readers; ICAO e-passports and readers; ISO devices (PICC and PCD), HF and UHF RFID tags and readers.
-
SR15-A1 -
Hukseflux Thermal Sensors B.V.
SR15-A1 is a high-accuracy solar radiation sensor. It is” First Class” according to the ISO 9060:1990 standard and “Spectrally Flat Class B” in the 2018 revision. With its on-board heater, it is compliant in its standard configuration with the requirements for “Class B” PV monitoring systems of the new IEC 61724-1:2017 standard. SR15-A1 measures the solar radiation received by a plane surface from a 180 o field of view angle.
-
UI-TX06 -
Unuo Instruments
ICI Pilling Tester – ICI pilling and snagging tester – ICI pilling box is applied to test pilling, snagging and fuzzing of fabric surface by tumbling randomly. ICI pilling test method includes ISO 12945.1, BS 5811, GB/T 4802.3, JIS L1076 and etc. UI-TX06 pilling and snagging tester is made with different standard box and can save your cost if different test standards are required.
-
RapiTime -
Rapita Systems Ltd.
*Timing analysis (inc. WCET) for Ada, C & C++ on-target & host**Identify code to optimize for worst-case behavior*Debug rare timing events*Simplify verification through integration with your CI tool*Produce evidence for DO-178 and ISO 26262 certification
-
NCT-500 -
ShinewayTech
ShinewayTech NCT-500 Network Cable Tester,Functions ranging from ISO / OSI reference model physical layer, link layer, network layer multiple detection. One machine in hand, which can quickly locate network faults and determine the link quality.
-
Mountz Inc.
High-value products manufactured to clean room standards need quality tools. Located in Silicon Valley, Mountz makes clean room screwdrivers that exceed Class 100 (ISO 5) clean room standards. Our built-in cam-over mechanism ensures industry-leading accuracy in even the most sensitive of environments. Mountz clean room screwdrivers offer companies the security of knowing the products they've invested in turn out exactly as designed.
-
TLS -
Mountz Inc.
TLS is a preset torque limiting screwdriver (internally adjustable). Built with a cam-over design, the accurate torque screwdriver prevents a fastener or bolt from being over-torqued. When the torque screwdriver reaches the pre-set torque value the internal mechanism disengages from the drive thus limiting the torque applied. Using a quality torque screwdriver ensures that proper torque is being applied and maintains requirements associated with ISO quality standards.
-
Ci3000+ -
Atlas Material Testing Technology
The Ci3000+ Weather-Ometer and Fade-Ometer with their advanced digital control systems, represent monumental achievements in applying digital and optical technologies in easy-to-use laboratory weathering instruments. The 3000 Series is approved by many OEMs in the textiles, paints & coatings and plastics industries as the exclusive platform to deliver accurate, reproducible and repeatable results for predicting service life. The 3000 Series has been certified CE, UL, CSA, ISO and EN compliant.