Showing results: 166 - 180 of 324 items found.
-
MI-8100 -
Ono Sokki
MI-8100 is a shotgun type directional microphone which sharply catches the intended sound. This directional microphone is helpful for the removal of background noise in the simple sound source exploration and in abnormal sound detection. Flat frequency characteristic from 50 Hz to 20 kHz and sharp detection with high S/N ratio provide high sensitive detection of various sound coming from the specific direction. By combining the acoustic vibration monitor BL-1100, only the intended frequency or sound is focused and caught clearer.
-
EQUINOX -
M Squared Lasers
Equinox is a single frequency, 532 nm continuous wave laser designed for a range of scientific applications including pumping any Ti:Sapphire laser systems. It is engineered to meet the needs of experimentalists requiring high-performance systems with an emphasis on reliability, stability and ease of use. The laser incorporates pump diodes within the central unit and is fully automated with hands-free operation and control via ethernet, webpage and TCP/IP remote interface. This completely sealed system is inherently stable with low noise levels <0.05 % RMS and ultra-stable output powers with ±0.5 % stability. Equinox has options of high output power up to 18 W. Other major applications include mixing source, pump source for dye lasers and frequency doublers, optical tweezers, and biomedical imaging.
-
CG118 -
EMC Instruments Corporation
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
De Vries Scientific
The Portable Telemetry Signal Simulator is a hand held, battery powered, synthesized signal source for testing of telemetry receiving systems. Frequency can be set to any value between 2200 and 2300 MHz in 500 KHz steps. Output power level can be set from +10 dBm to –20 dBm in 1 dB increments.
-
RSA 3000 Series -
Rigol Technologies Inc.
The RSA3000 real-time spectrum analyzer with real-time analysis and sweep analysis capabilities, optional EMI measurement application software (EMI), with excellent performance and specifications. Its frequency range is 9kHz to 3.2GHz, and it is available with the tracking source "-TG" model, which can be widely used in enterprise R&D, factory production, education and teaching.
-
RSA 3000E Series -
Rigol Technologies Inc.
The RSA3000E is a 5-in-1 spectrum analyzer with sweep spectrum, real-time spectrum, scalar network analyzer (-TG model), EMI receiver and digital demodulation. Its frequency range is 9kHz to 1.5/3GHz, and it is available with the tracking source "-TG" model, which can be widely used in enterprise R&D, factory production, education and teaching.
-
TH1775 -
Shenzhen Chuangxin Instruments Co., Ltd.
TH1775 is a DC Bias Current Source (or DC Magnetization Current Source) used for inductance measurement of inductors and transformer windings with DC bias current. Except for constant current output, low additional error and wide frequency response range are important for bias current inductance measurement. High frequency LCR meter could be used, when the frequency response range is wide enough. MPU controlled auto current balance technology is adopted to realize AC+DC current overlap and constant current output from 0 to ±20A. Two TH1775 can be paralleled to supply a maximum current up to 40A.TH1775 permits high frequency measurement up to 1 MHz and can be directly controlled by TH2816A, TH2817A, TH2818 and TH2819. TH1773/TH1775 with its low additional error, wide frequency response range and sweep output function is widely used in DC biased inductance measurement. TH1775 also provides a perfect solution for magnetic material analysis.
-
AMETEK Sensors, Test & Calibration
Our multifunction process calibrators read and source RTD, thermocouple, current, voltage, frequency, and resistance to calibrate or verify your process sensors. They can also be combined with APM CPF pressure modules to calibrate pressure, or a dry-block to calibrate temperature. The ASC-400 features a large full color display with an advanced simplicity, easy-to-use interface.
-
A10200 -
Tabor Electronics Ltd.
Model A10200 is an ultra-small footprint, ultra wideband, high power amplifier designed for high frequency, high power, signal amplification. With an ultra high bandwidth of almost 20GHz and up to +28dBm power into 50 ohms, the A10200 is the ideal complimentary amplifier to any signal source that needs an extended power boost for demanding applications.
-
Panda Microwave Limited
Panda Microwave customized up to 40GHz low phase noise (DRO or PDRO) , Phase Locked Dielectric Resonator Oscillators (PDRO) take advantage of the small size, low phase-noise and high efficiency, including PDRO and DRO. Phase Locked Dielectric Resonator Oscillators (PDRO) are used widely in today’s electronic warfare, radar and communication systems. They find use both Commercial and Military communication systems where demanding performance, high reliability and cost are critical. The phase locked oscillators utilize ceramic coaxial resonator and ceramic dielectric resonator fundamental frequency sources with low phase noise performance. The design of the Phase Locked Oscillators is based on sampling phase detector technology, which provides the comparison frequency at the same frequency as the fundamental frequency output.
-
DMC-1400 -
Martel Calibrators
The DMC-1400 Calibrator fully documents any calibration easily while performing the normal job. No special software is required! It features the ability to test for pass/fail criteria, measure and simulate thermocouples, RTDs, current, voltage, and frequency, and source pulse trains. PLCs, full fuseless protection, and a serial communications port for full control with ASCII commands.
-
Model: DS-7240 -
De Vries Scientific
The Telemetry Signal Simulator is intended for laboratory use in the testing of telemetry receiving systems. The unit features a fully synthesized signal source that can be set to any telemetry frequency in the 2200-2300 MHz band in 500 KHz steps. The simulator has an internal attenuator that can set the signal level from +10 dBm to 20 dBm in 1 dB steps.
-
N7711A -
Keysight Technologies
The Keysight N7711A and N7714A tunable lasers are single-port and four-port sources, available with C-band or L-band wavelength coverage. The narrow linewidth and offset grid fine-tuning capability make them ideal sources for realistic loading of the latest transmission systems. All models can reach any wavelength point within their specified wavelength range just like all other Keysight tunable lasers. In this mode, code compatibility with existing test setups based on Keysight's range of full-size and compact tunable lasers is a great asset. In system loading applications, it may be preferable to grid-tune the lasers like system transmitters, simply by changing the channel index. The channel grid is adjustable to standard ITU-T grid spacing like 50 GHz, and to arbitrary grids. Likewise, the zero frequency (base channel) of the chosen grid is adjustable. A 12 GHz fine-tuning range allows de-tuning the frequency.
-
N7714A -
Keysight Technologies
The Keysight N7711A and N7714A tunable lasers are single-port and four-port sources, available with C-band or L-band wavelength coverage. The narrow linewidth and offset grid fine-tuning capability make them ideal sources for realistic loading of the latest transmission systems. All models can reach any wavelength point within their specified wavelength range just like all other Keysight tunable lasers. In this mode, code compatibility with existing test setups based on Keysight's range of full-size and compact tunable lasers is a great asset. In system loading applications, it may be preferable to grid-tune the lasers like system transmitters, simply by changing the channel index. The channel grid is adjustable to standard ITU-T grid spacing like 50 GHz, and to arbitrary grids. Likewise, the zero frequency (base channel) of the chosen grid is adjustable. A 12 GHz fine-tuning range allows de-tuning the frequency.
-
EMIC Corporation
The compact vibration generator is used for calibration of a vibrometer, measurement of mechanical impedance, excitation source for modal analysis and reliability test of a small light specimen. In particular, EMIC uses the world's first ceramic armature for the 512-D and 513-D vibration generator,making it possible to excite up to high frequency of 30 kHz (513-D can excite up to 24 kHz).
