Showing results: 496 - 510 of 980 items found.
-
DP-VME-3636 -
Data Patterns Pvt. Ltd.
DP-VME-3636 is a 64-Channel Isolated Digital Input/Interupt/Output Module. This module provides 32 channel digital input and 32 channel digital output with isolation. Channels are divided in 2 groups of 16 channels each and are routed to rear I/O. 16 non-isolated TTL channels are available.The module is used for digital interface, status setting, status monitoring, automatic test equipment, and high density industrial automation.
-
V250 -
Highland Technology, Inc.
The V250 is a single-wide, 6U VME module that provides 64 non-isolated channels of digital input/output. Each 16-channel bank shares programmable pull-ups and input thresholds with a range of 0 to +10 volts.
-
DP-VME-5826 -
Data Patterns Pvt. Ltd.
DP-VME-5826 is a VME64x Six Channel Digital IF Receiver module. It samples and down converts analog IF signals into the digital base band data.The digital base band I/O samples generated from these IF samples are pulse compressed. Down converted I/Q data is sent to the signal processor through 2 channels of 2.5 Gbps speed SFPDP link.The digital waveform generator block of digital receiver unit generates programmable polyphase coded digital pulse coded expander output.
-
2979 -
Technobox, Inc.
The 80-channel Reconfigurable Digital I/O PMC provides a vehicle for implementing complex user-specific digital designs requiring high speed single-ended operation. 64 of the 80 signals are available out the PN4 connector, while all 80 signals are wired to the front panel connector.
-
PAS 9795/DIO -
Precision Analog Systems Co.
The PAS 9795/DIO is a VME based, 80 Channel, TTL level, Digital Input / Output card. Sixty-four of the channels are arranged as eight byte wide bi-directional data ports. Each port consists of an eight-bit output data register with output enable, and an eight bit input buffer. The input buffers always monitor the state of the I/O lines, and the output data registers can either drive the I/O lines, or disconnect from the I/O by assuming a high impedance state.
-
AIO8 -
Acces I/O Products, Inc.
AIO8 is an economical multifunction, moderate-speed, multiplexed analog-to-digital converter card with digital I/O and with counter/timers. It can be used with ISA-bus computers. The card is 7" long and requires one slot in the computer. All external connections are made through a standard 37-pin D-type connector at the rear of the computer.
-
APCIE-2200-8-8 -
TEAM SOLUTIONS, INC.
- 8 electromechanical relays with change-over contacts The PCI-Express 8 relay board APCIe-2200-8-8 has 8 relay output channels and 8 isolated digital inputs, 24 V. 7 inputs are interruptible. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
-
FMC216 -
Vadatech Inc
The FMC216 is an FPGA Mezzanine Card (FMC) per VITA 57 specification. The FMC216 utilizes AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a DAC AD9129 providing 14-bit conversion rates of up to 5.6 GSPS. The analog input/output, digital output, clock and trigger interfaces of the FMC216 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
Curtiss-Wright Defense Solutions
Many mission-critical applications require small form factor solutions, but cannot compromise ruggedization requirements or I/O and processing performance. Our VPX, XMC, PMC and FMC module-based sensor I/O solutions are designed to handle the toughest operating environments while packing maximum functionality in a minimal physical footprint. Our selection of analog I/O, digital transceivers, and receivers includes I/O for frequency and time-domain applications, as well as digital I/O. Interoperable with our range of SBC, FPGA, and GPGPU modules, these highly engineered cards are designed to simplify integration and let you focus on your application, not low-level connectivity.
-
DS-MPE-DAQ0804 -
Diamond Systems Corp
The DS-MPE-DAQ0804 is a rugged, low cost data acquisition PCIe MiniCard module with both analog and configurable digital I/O. It is ideal for adding analog I/O and digital I/O features to embedded and OEM applications requiring low cost, small size, and/or light weight.
-
IO105 -
Speedgoat GmbH
Fast 16-bit analog module with 64/32 multiplexed analog input channels. This I/O module offers sampling/conversion times similar to the IO102 and IO103 but comes with a higher analog input channel count of 64/32. Analog outputs and digital I/O are not available on this module.
-
PCIe-DA16-6 -
Acces I/O Products, Inc.
The PCIe-DA16-6 series are x1 10.5” cards that can be installed in long PCIe slots. They contain six, four, or two digital-to-analog converters (DACs) and 16 bits of digital I/O.
-
AD8-16 (ADA-8) -
Acces I/O Products, Inc.
Model AD8-16 (alternate part number ADA-8) is an economical, multiplexed, eight-bit Analog-to-Digital Converter (A/D) and Counter-Timer card for ISA-bus computers. It accepts up to eight differential or 16 single-ended analog inputs (jumper configured). AD8-16 requires a full-size expansion slot. All connections are made through a standard 50-pin connector. Base I/O address selection is via dip switch.Analog inputs are multiplexed, amplified, held by a sample and hold amplifier, and then digitized by an eight-bit A/D converter. Amplifier gain is selected by software and can differ from channel to channel.
-
ROB-00001 -
Playing With Fusion Inc
The ArgoBot Full Kit is a fully assembled robot and controls development platform. It is based on the Digilent chipKIT WF32(TM), a WiFi enabled development platform, and configured for LabVIEW targeting. Most importantly ArgoBot was designed with FIRST Robotics Competition teams in the front of our minds! Named after the FRC Team 1756 mascot, Argos, the ArgoBot development platform includes a fully-assembled, ready to drive mini WiFi enabled robot (about 8" x 5" x 4"), as well as tons of FRC controls tutorials and example code (LabVIEW VIs). Features included on the ArgoBot will look very familiar to anyone who has worked with National Instruments products (Compact RIO and RoboRIO) in the past. This includes three 5V Digital I/O modules (with jumpered pull-ups), three 5V analog inputs, and an I2C header. Example VIs have been streamlined to enable a 1-click configuration style to accelerate your development process. We also added a 2-channel motor driver that is used to supply the ArgoBot drive motors. Our ultimate goal is that everything you can build, control or implement on ArgoBot can be easily leveraged on your FRC bot! Complimenting its many electrical features, ArgoBot is easy to work with and easy to maintain. The chassis is a polycarbonate (the extremely tough stuff that is easy to drill and modify but easily takes bumps and bruises without cracking) case that is fully intact - meaning that ArgoBot doesn't just come with a case... it is a case! Clean-up and organization is simple - just close the case and turn off the power switch.
