Showing results: 451 - 465 of 477 items found.
-
VF-145 LA AND VF-145 LMA -
National RF, Inc
The VF-145 LA and LMA models are functionally the same as the VF-145 L and LM on both electrical performance and mechanical specifications. However, the LA and LMA models include an internal PIN diode attenuator that provides up to 12 dB of attenuation (measured at 150 MHz, attenuation decrease slightly as operating frequency increases) to the incoming radio signal. This attenuation occurs after the signal is received by the unit and phase shifted for processing, but before it is placed on the coax feedline to the receiver. In addition, the PIN diode utilized will absorb short burst of RF should transceivers be keyed accidentally by the user. This feature aids in very strong signal DF operations but will not totally guarantee against system overload under very strong RF emissions.
-
Analog Devices Inc.
LVDS (Low Voltage Differential Signaling) Drivers and Receivers from Analog Devices offers designers robust, high speed signaling for single-ended to differential solutions for point-to-point applications. Our selection of products conform to the TIA/EIA-644 LVDS standard and contain the first LVDS transceivers to meet 8 kV IEC ESD performance standards - important for robust, interboard applications where the connectors can be exposed to more harsh electrostatic environments. Companion differential line receivers and differential line drivers support up to 600Mbps. LVDS greatly improves noise immunity and minimizes emissions for high speed point-to-point data transmission and is a low power alternative to emitter-coupled logic (ECL) or positive emitter-coupled logic (PECL) signaling.
-
Talon RTX 2586 -
Pentek, Inc.
- Rugged 1/2 ATR MIL-spec chassis for harsh mechanical and thermal environments- Environmentally sealed- Internally conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight design - 18 lb (8 kg)- QuickPac® drive packs allow quick removal of all data storage up to 61 TB via the front panel- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- RF/IF recording with phase coherent 200 MHz 16-bit A/Ds and DDCs- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow GUI, API and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
AL-130R -
Com-Power Corporation
Also known as Magnetic Loop Antenna, the AL-130R is compliant with CISPR 16-1-4. It is ideal for emissions measurements as required by various EMC standards such as FCC 18, CISPR 11, CISPR 13, CISPR 14, CISPR 32 and many more. The built-in, low-noise preamplifier, increases overall measurement sensitivity as well as the overall signal to noise ratio. As per ANSI C63.4-2014, the use of active loop antenna for compliance testing is permitted in a non-sheilded environment ONLY if the saturation indicator is continuously monitored during the course of testing. Com-Power’s Remote Antenna Interface (RAI-100) comes in very handy for this application. It is a compact controller which can be used to enable/ disable RF measurement circuit and monitor saturation and battery low conditions remotely via a fiber optic cable up to 30 mtrs in length.
-
ECU1/ECU2 Series -
Shimadzu Corp.
Up to 50 % energy savings. Contributes to reduced CO2 emissions and lower running costs. The conventional hydraulic power supply unit for fatigue and endurance tests is always driven at full power to achieve the maximum test force and maximum velocity and the hydraulic power supply unit is selected in order to satisfy the maximum test performance. Therefore, depending on the test conditions, energy is excessively consumed. With the ECU Series the motor rotational speed and the supply pressure of the hydraulic power supply unit can be set in multiple stages, so energy savings of up to about 50% can be achieved depending on the test conditions and test circumstances. It is used in combination with the Servo Controller 4830. (The Servo Controller 4830 is provided separately.) * Appearance and specifications are subject to change without notice.
-
PDetector -
Power Monitoring and Diagnostic Technology Ltd.
The PDetector is an ideal device for On-Line Partial Discharge (OLPD) testing of MV and HV equipment which employs all 5 types of OLPD sensor technology: Ultra-High Frequency (UHF), Acoustic Emissions (AE), Ultrasonic, High Frequency Current Transformer (HFCT), and Transient Earth Voltage (TEV). The information from multiple sensors gives the PDetector the versatility to detect all types of PD in all types of substation apparatus. The exact type of PD activity can be determined effectively using multiple on-screen data spectrum analysis. The PDetector greatly simplifies and standardizes the routine OLPD testing procedure by using the Intelligent Patrol function, the PDetector App, and the PMDTCloud. It is a very powerful and helpful tool for substation operators to conduct routine testing in a substation quickly, to determine what the issue is, and where it is located.
-
Talon RTX 2589 -
Pentek, Inc.
- Rugged 1/2 ATR MIL-spec chassis- Designed for harsh mechanical and thermal environments- Environmentally sealed- Internally conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight design - 22 lb (10kg)- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- Capable of recording RF/IF frequencies to 2.8 GHz- Ultra Wideband recording with 3.6 GHz 12-bit A/D- Selectable 1.8 GHz dual channel mode- Up to 61 TB of solid state storage in removable QuickPac- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow API, GUI and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
ENDA-5000 series -
HORIBA, Ltd.
Continuous simultaneous and high-precision measurement of NOx, SO2, CO, CO2 and O2.HORIBA has over 100,000 CEM systems installed and 30 years of quality and experience. That is the base on which HORIBA's new ENDA-5000 series of stack-gas analysis systems are built. These systems have a small footprint and use cross-flow modulated non-dispersive infrared (NDIR) and magneto-pneumatic detectors that are inherently drift-free. The ENDA-5000 series are superior continuous analysis systems that perform reliably for difficult exhaust gas measurements, when measurement errors cannot be tolerated. This CEM series features a new intuitive touch panel that makes every operation available with the touch of a single button. The ENDA-5000 series systems are also designed for ease of maintenance. They are ideal for a variety of uses, including emissions monitoring from steam boilers, refuse incinerators, and electric power generation plants to assure pollution standards are being met.
-
LF1 set -
Langer EMV-Technik GmbH
The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5 and LF-U 2.5 are used to more precisely detect any source of interference. The probe heads are designed for taking measurements at single pins and larger components. Near-field probes are small and handy. They have a current attenuating sheath and, therefore, are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. The H-field probes do not have an internal terminating resistance of 50 Ω.
-
Talon RTX 2596 -
Pentek, Inc.
- Rugged 1/2 ATR MIL-spec chassis for harsh mechanical and thermal environments- Environmentally sealed, conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight design - 18 lb (8 kg)- QuickPac® drive packs allow quick removal of all data storage up to 61 TB via the front panel- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- Four-channel Serial FPDP record/playback- Supports Flow Control, CRC, and Copy/Loop Mode as a receiver and transmitter- Supports 1.0625, 2.125, 2.5, 3.125 and 4.25 GBaud link rates- Single-mode and multi-mode fiber interfaces available- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow API, GUI and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
AFM-8A -
Chuan Sheng Electronics Co., Ltd.
AFM-8A has Developed for AFC*(Auto Frequency Control) high performance measurement and frequency update, its update up quickeer than 100mSec. multifunction power analyzer provides high-accuracy measurement and is designed for single phase and three phase application. It includes 4 Digital inputs, 4 Relay outputs, and a RS-485 Modbus RTU Communication port. The user can choose one more communication port, and 2 Analog outputs for output expansion.It provides measure voltage and current of the 2~63 harmonic, and it shows CO2 emissions, which is suitable for power monitoring, management and analyze power quality. It has TOU (time-of-use) function and 4MB Flash memory capacity, allowing users to record data for a long time. It also has a software line adjustment function to reduce the on-site line adjustment work.It has the functions of waveform capture and recording, power record, and event record, which can be used for multifunction power analyzer.
-
FIM-71 VHF -
Potomac Instruments, Inc.
The Model FIM-71 is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-71 is suitable for practically all types of RF emission measurements in the 45 MHz to 225 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and a meter dynamic range of either 20 dB or 60 dB. A dc analog output voltage, proportional to the meter indication, is provided for driving a chart recorder. A leveled output from the calibrating oscillator is available for measuring cable insertion loss, filter response, amplifier gain, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
-
FIM-72A UHF -
Potomac Instruments, Inc.
The Model FIM-72A is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-72A is suitable for practically all types of RF emission measurements in the 450 MHz to 960 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and meter dynamic range of either 20 dB or 60 dB. A dc analog voltage, proportional to meter indication, is provided for driving a chart recorder or similar device. A leveled output from the calibrating generator is available for measuring cable insertion loss, filter response, amplifier gain, VSWR, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
-
EU Series -
ADLINK Technology Inc.
The ADLINK complete EtherCAT solution, from hardware to middleware to software, with every element tailored for dedicated EtherCAT functionality, includes Talos master controllers, EU & EPS slave systems, and remote monitoring and control providers. As well, ADLINK’s Softmotion one-stop control kernel delivers flexible and easy-to-use intelligent platforms for driving next-generation modern Smart Factories. ADLINK's EU slave system brings the powerful flexibility to EtherCAT environments. State-of-the-art modular construction allows the EtherCAT slave to be configured to fulfill the needs of both small local applications and expansive distributed platforms. The EU system incorporates and controls nearly any type of I/O devices. Uniquely designed for full operability in conditions from 0°C to 55°C, the EU slave system is also fully compliant with the EN 61131-2 standard for shock and vibration and EN 61000-6 for heavy industrial EMC protection, as well as emission certificate.
-
RegPerfect -
Teledyne Monitor Labs
Data management is vital to your company's bottom line and mission critical environmental compliance goals. Today's environmental professionals must learn to do more with less when faced with budget constraints, rising operating costs, and staff reductions. TML helps environmental professionals around the world meet these challenges by offering RegPerfect Software.The Teledyne Monitor Labs RegPerfect® software system is a state of the art Data Acquisition Handling and Reporting Sytem. RegPerfect® is the culmination of more than 40 years of experience in the data acquisition system business. The software is designed to comply with the data collection, quality assurance, and reporting requirements of federal and local regulatory agencies. Operating in real time, this rugged platform provides the visibility, connectivity and securityfor all of your environmental and operational needs related to the performance of your Continuous Emission Monitoring (CEM) System. For the most recent updates to the software, please visit the Product Status page.