Showing results: 466 - 477 of 477 items found.
-
EMC Technologies Pty Ltd
Having been assessed by Ford Detroit’s EMC expert, we are Australia’s only Ford (and NATA) accredited automotive EMC test laboratory. Others have tried, but none have succeeded. Ford does not accept reports from EMC labs that are not on the Ford list of accredited labs. The scope ranges from component to complete vehicle level EMC testing for Australian and overseas manufacturers. We also have a fully dedicated CISPR 25 Electronic Sub Assembly (ESA) chamber, another large CISPR 25 anechoic chamber for vehicle testing or susceptibility levels in excess of 500V/m. We possess a vast array of specific automotive EMC test equipment such as BCI’s, tri-plate’s, and striplines for susceptibility and emissions testing to meet the most stringent automotive EMC requirements. Our Australian and overseas customers use our labs because they know that our reports will be accepted and will not be questioned.
-
VUVAS-10X -
McPherson, Inc.
A new ultraviolet spectrophotometer system for optical metrology just arrived at NASA Goddard! The VUVAS-10X spectrophotometer works best in the 90 to 160 nanometer wavelength range, also known as deep or vacuum ultraviolet (VUV) region. It uses a windowless hydrogen plasma light source and differential pump section to reach many wavelengths beyond those of conventional deuterium lamps. The source also works with other gases, or gas mixtures, for atomic spectral line emission from about 30 nanometers (double ionized Helium gas) up to the Visible light range. The new spectrophotometer system, McPherson VUVAS-10X, uses a one-meter focal length high-resolution monochromator with the special light source, scintillated detector and Model 121 goniometric sample chamber. The system is ideal for optical transmission, absorbance and specular reflectance at incident angles up to 60 degrees. This McPherson spectrophotometer system will help develop, inspect and qualify optical materials and coatings used for very high altitude and extraterrestrial space flight missions.
-
Inframet
Solar blind UV cameras are imaging devices optimized to detect ultraviolet light of wavelengths below about 280nm. Such cameras are insensitive against sunlight due to negligible sensitivity to visible and long wavelength UV light. Solar blind UV cameras are used in a series of applications like corona detection, fire detection, combustion analysis, plasma research, testing UV lamps, etc. However, highly sensitive corona detection is the main mass application and these devices are of crucial importance in electric power industry. These imaging devices enable easy detection of degraded insulators of high voltage transmission lines, distributions and substations. They can see the emission of UV light when discharges occur at defect insulators. From design point of view solar blind UV cameras are actually bispectral imaging systems built by combining true UV camera with typical visible camera. These bispectral imaging system generate output image as overlay of typical visible image with UV image of analyzed UV source.
-
IT8300 Series -
I-TECH Electronic Co., Ltd
ITECH newly launched IT8300 Regenerative DC Electronic Load, it not only can simulate various load characteristics, but also can feed power back to grid without pollution. IT8300 series unique regenerative function can convert the absorbed DC power into AC power and feed it back to local grid. This eliminates the usual heat dissipation to a minimum and saves energy costs, adapts requirements of global energy-saving and emission reduction at the same time. IT8300 adopts shigh power density design, e.g. for 3 U size, it can absorb power up to 10.5kW. IT8300 supports master-slave paralleling and current equalized distribution, which can expand the power up to 105kW or more. Moreover IT8300 has multiple functions such as the automatic grid-state detection, on-grid electricity accumulation, anti-islanding protection, battery-test function, dynamic mode, LIST function, etc. The built-in interfaces include LAN/USB/RS232/RS485/CAN interfaces. The various functions make IT8300 series suitable for high-power power supply, storage battery, photovoltaic battery,electric vehicle, energy storage system, etc.
-
Talon RTX 2684 -
Pentek, Inc.
- Search and capture system using Pentek's Sentinel™ Intelligent Signal Scanner- Captures RF signals from 1 GHz to 26 GHz- Capture and scan bandwidths up to 500 MHz- Selectable threshold triggered or manual record modes- 12-bit A/Ds with 57.5 dB SNR & 72 dB SFDR- Built-in DDC with selectable decimations of 4, 8 and 16- Rugged 1/2 ATR MIL-spec chassis for harsh mechanical and thermal environments- Environmentally sealed- Internally conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight: about 23 lb (10.4 kg)- QuickPac® drive packs allow quick removal of all data storage up to 61 TB via the front panel- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow® GUI, SystemFlow API, and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
EL Imaging Tester -
OAI
EL Testing for Si Solar Cells using High Performance CCD. The determination of luminescence (photo emissions) in solar cells is an important characterization tool. Typical solar cells often have defects which limit the efficiency or lifetime of a cell. Many of these defects are visualized with Luminescence Imaging. By using this technique, the manufacturing process can be optimized to produce better cells. Luminescence Imaging takes advantage of the radiative inter-band recombination of excited charge carriers in solar cells. The emitted photons can be captured with a sensitive CCD camera to obtain an image of the distribution of the radiative recombination in the cell. This distribution is determined by the local excitation level, allowing the detection of electrical losses, thus mapping the diffusion length of minority carriers as the emitted light is low intensity and in the near infra-red range, the CCD camera has a high sensitivity wavelength from 900 to 1100 nm with little thermal noise. This CCD camera provides excellent resolution of 1024 x 1024 pixels with a large 1μm pixel size, multi-megahertz readout speed, and robust USB 2.0 connectivity. The EL CCD Camera is the ultimate high-performance CCD camera for electroluminescence and photoluminescence imaging for Photovoltaic (PV) Cells and Modules. This camera combines low noise electronics and optimal sensitivity in NIR.
-
TDEMI eXtreme series -
Gauss Instruments
Highest measurement speed. Highest accuracy. Incredible dynamic. New operation modes. The novel product line TDEMI eXtreme (TDEMI X) is the latest and most advanced level of full digital measurement equipment for emission testing on the fast lane. It is based on the unrivaled and patented TDEMI® real-time technology of GAUSS INSTRUMENTS. It is easy and efficient in upgrading its frequency range by a various number of extensions which can be integrated into the instrument step by step. The frequency ranges are 1 GHz, 3 GHz, 6 GHz, 18 GHz, 26.5 GHz or 40 GHz respectively. A large variety of configuration possibilities makes the TDEMI X to the customized solution perfect fitting into your lab and to your application according to civil standards (e. g. CISPR, EN, FCC Part 15, ANSI C63.2, ANSI C63.4), military standards (e. g. MIL-461G, but also its previous versions and revisions) as well as avionic standards (e. g. DO-160). The frequency range of the TDEMI X instruments starts at 9 kHz in its standard configuration and can be extended down to 10 Hz by the option MIL/DO-UG or even down to DC by the available option OSC-UG as well. Like all other TDEMI measurement systems, the TDEMI X measurement systems can be remotely controlled and fully automated via Ethernet (TCP/IP) very easily.
-
PCE Instruments
A geiger counter detects nuclear radiation by measuring the emission of ionizing radiation of alpha particles, beta particles and gamma rays. Also referred to as a radiation detector, a geiger counter consists of two main elements: the processing electronics and the geiger tube. The geiger tube is filled with low-pressure inert gas like helium, argon or neon. If radioactive radiation occurs, the inert gas is ionized. An anode within the geiger tube registers the quantity of ionized particles numerically correlating with the strength of the radioactive radiation. The radioactivity measurement is then displayed on the LCD screen of the geiger counter or radiation detector.It is very important to measure radioactivity as well as to classify radioactivity values. For example, terrestrial gamma radiation is measured according to general values from 0.03 - 0.3 µSv/h (microsievert / hour). This "normal" oscillation range is conditioned by natural radioactive elements in the ground such as uranium and potassium. To calculate this factor, one must take into consideration cosmic radiation. For example, when considering cosmic radiation, the maximum radioactivity content at Schneefernerhaus, the highest-located German environmental research station, is approximately equal to 110 µSv/h.At PCE Instruments, you will find three types of geiger counter or raditation detection devices to help you measure radioactivity: 1) alpha radioactivity meters, 2) meters for detecting alpha, beta and gamma radioactivity and 3) radioactivity meters for human beings.
-
EPS Series -
ADLINK Technology Inc.
The ADLINK complete EtherCAT solution, from hardware to middleware to software, with every element tailored for dedicated EtherCAT functionality, includes PCIe-833X Series master controllers, EPS slave systems, and remote monitoring and control providers. As well, ADLINK’s Softmotion one-stop control kernel delivers flexible and easy-to-use intelligent platforms for driving next-generation modern Smart Factories. ADLINK's EPS slave system brings the power the flexibility to EtherCAT environments. State-of-the-art modular construction allows the EtherCAT slave to be configured to fulfill the needs of both small local applications and expansive distributed platforms. The EPS system with comprehensive and high-density I/O modules that include DI/O, pulse-chain motion modules. Leveraging ARM and FPGA technologies, the EPS slave is able to monitor and report system integrity via EtherCAT communication, while relay module lifecycle and signal integrity of analog output are monitored cyclically, and hot swappability reduces downtime significantly. Uniquely designed for full operability in conditions from -20°C to 60°C,the EPS slave system is also fully compliant with the EN 60068-2 standard for shock and vibration and EN 61000-6 for heavy industrial EMC protection, as well as emission certification. Corresponding ESI files for each EPS system can be generated thru ADLINK's Windows-based EtherCAT slave utility, LinkMasterPro™.
-
Cincinnati Sub-Zero Products
We supply a variety of test chambers for testing small battery cells to large lithium ion battery packs. Battery test chambers are supplied to a variety of industries including telecommunications, computer and automotive. With the goal of reducing automobile emissions and the development of electric vehicles, the need for lithium ion battery testing is even more critical. Our proven experience provides the most cost-effective solutions. Each test chamber is built according to specific test requirements and may be interfaced with battery cyclers, control & monitoring data acquisitions systems and other test equipment for a complete integrated test solution. All environmental chambers are designed with safety in mind. A variety of safety features are provided for reliability and abuse testing of batteries. These features may be incorporated into CSZ test chambers and tailored to the various hazard levels of EUCAR (European Council for Automotive R&D), a consortium of European car manufacturers. To better assess the hazard potential of tests, EUCAR has investigated hazardous situations and divided them into eight risk classes. The development of the safety equipment of our battery test systems is also based on this classification. For each hazard level, we recommend specific safety options that can be included with your chamber to meet your specifications to safety test your product. Together with our customers, we assess which safety devices are necessary for the respective test chambers.
-
TDEMI Mobile+ series -
Gauss Instruments
The new benchmark for your fastest product pre-certifications on the planet. The new TDEMI Mobile+ (TDEMI M+) receiver series of GAUSS INSTRUMENTS is a very compact and robust designed instrument for optimum mobility and outdoor use as well as on developers workbench in your lab. It provides a vast variety of functionalities. The TDEMI M+ receiver series is equipped with a +12V supply - so it can be easily used for on-board testing, e. g. in vehicles or aircrafts and so on. By its integrated touch-sensitive and high resolution screen and the embedded PC the TDEMI M+ is a fully stand-alone instrument independent from any control or host or display unit e. g. as a PC or laptop. Thus it provides even more flexibility for your emission measurements. Furthermore the instrument can be powered by a battery pack (Option BAT-UG) making it even more flexible and easy to carry it around without any need of an external power supply. Especially designed for your todays challenging pre-certification tasks the TDEMI M+ provides the absolutely unrivaled advantages in speed and performance of the well known and market approved GAUSS INSTRUMENTS time-domain and RF technology. Thus, your pre-certification measurements and investigations can be performed up to 16000 times faster than by conventional receivers. The instruments of the TDEMI M+ receiver series are available for the frequency ranges up to 1 GHz, 3 GHz, 6 GHz or 7 GHz starting from 9 kHz each. Additionally these blazing fast measurements can be carried out even starting from 10 Hz optionally (Option MIL/DO-UG).
-
MD-250-HD -
Mustang Dynamometer
The MD-250-HD series dyno (SE/DE) was designed to be a performance dynamometer first with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles in addition to the standard car or light duty pick-up. The 250-HD is certified in the states of Colorado, Nevada and Utah for use in loaded-mode diesel smog testing programs because of its accuracy and reliability. No other dyno in its class offers more value or better in-house motor vehicle testing capabilities than the Mustang MD-250-HD. For starters, the MD-250-HD boasts a 1,500 horsepower measurement capacity at a top speed of 175 mph and a powerful air-cooled eddy current brake provides the MD-250-HD-SE with 900-hp worth ofloading capacity for steady state testing. Loading capacity can be increased to 1,500-hp via the optional DE model. The 250-HD can be upgraded to the 250-HD-SE-M via the addition of a 100 or 200 hp AC motor for transient testing of electric buses to measure range and regeneration or for emissions testing of IC engines. Do not be fooled by its compact size – the MD-250-HD is a serious dynamometer with serious tuning capabilities. The MD-250-HD uses a powerful eddy current power absorber, a frictionless, air-cooled braking device, to enable it to apply variable and steady state loading. A complete control and data acquisition system lets you design a wide range of tests or select from a host of pre-configured tests included with the standard system. The 250-HD’s four roller design makes setting up vehicles a snap – simply drive onto the 250-HD and let the tires settle in between the rollers. The 250-HD can be installed above-ground or below-ground, it’s your choice. The above-ground system utilizes an optional premium platform and ramp system with an above-ground restraint kit. The addition of an axle pull-down kit help keep the tires from slipping or trying to “climb out” of the rollers.