Showing results: 841 - 855 of 905 items found.
-
781964-03 -
NI
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
CBG830 -
MicroImage Video Systems
The CBG830 color bar and test signal generators will produce a quality, high definition full field color bar signal compatible with the digital HDMI and DVI-D interfaces. The CBG830 is designed to provide an accurate and affordable signal source for easy testing of displays, cables and systems.The CBG830 will generate a full field color bar signal with eight vertical bars, white through black. This signal is available in a variety of resolutions and refresh rates. TheCBG830 will usually fit in a toolbox with ease and even fit into a pocket. There is also a rack mount kit available as well. Power is provided by a regulated 5VDC source and a small wall plug power module is included with the packaged CBG830 but not with board level products. The CBG830 will have a switch array to select the video standard.
-
Thorlabs, Inc.
Thorlabs' Mode-Conditioned Light Sources are fiber-coupled LED sources that have an output with a flat-top profile in the far field. Common applications include the testing of multimode fused fiber components as well as verification of modal behavior in fiber-based setups. Standard fiber-coupled LED sources can have a range of output profiles that are usually not uniform and vary from source to source. This can be dependent on emitter orientation, alignment with fiber tip, and connector assembly. These mode-conditioned sources have been engineered to distribute light evenly into all transverse modes, resulting in an equilibrium modal distribution at the output. The front panel includes an adjustment knob to control the power and an output port that accepts 2.2 mm wide-key FC/PC connectors. A DS15 15 V power supply with a location-specific plug is included with each device.
-
MX Series -
AMETEK Programmable Power, Inc.
The California Instruments MX Series consists of multiple high power AC and DC power systems that provide controlled AC and DC output for ATE and product test applications. This high power AC and DC test system covers a wide spectrum of AC and DC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the California Instruments MX series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the MX15, MX22.5, MX30, or MX45 unit to its designated location (using included casters), plug it in, and the MX series is ready to work for you.
-
Shoghi Communications Ltd.
Unified Satellite Phone Monitoring System is designed to intercept Voice, SMS and Text traffic from Satellite Phones operating on Thuraya, Iridium and IsatPhone Pro Satellite networks. The system is pre-integrated & pre-configured in a compact ruggedized transportable casing for plug and play operations. It intercepts the signals from L-band uplink (from Satellite Phones to Satellites) and downlink (from Satellite to Satellite Phones) to provide the duplex calls up to 15 Kms with LOS and beyond that simplex calls. System is equipped state-of-the-art high performance Thuraya and IsatPhone Pro decryption module , Iridium proprietary protocol module to provide processed intelligible output in the form of Voice, SMS and Text along with session related information such as Called Phone Number (for session initiated by Satellite Phone),Caller ID, TMSI/IMSI/IMEI and geo-location
-
Pasternack Enterprises, Inc.
Pasternack SMC connector category has dozens part numbers, most of which are RoHS and REACH compliant. SMC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These SMC connectors are built to precise RF and microwave industry specifications. Pasternack connectors with SMC series are built in jack or plug gender with 50 Ohm impedance. SMC connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SMC connector designs include clamp/solder, crimp/solder or solder attachment methods. as with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMC connector series is in-stock. In addition to being in stock, these connectors will ship the same-day as purchased.
-
Pasternack Enterprises, Inc.
BNC Twinax connector category has several part numbers, the majority are RoHS and REACH compliant. BNC Twinax connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our BNC Twinax connectors are built to precise industry specifications. Pasternack BNC twinax connector items are available in jack or plug gender with 78 Ohm impedance. Connectors in twinaxial BNC are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These BNC Twinaxial connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this twinax BNC connector series is in-stock. In addition to being in stock, these twinaxial BNC connectors will ship the same day as they are purchased.
-
Pasternack Enterprises, Inc.
Pasternack SMB connector category has dozens of part numbers, most are RoHS and REACH compliant. SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our SMB connectors are built to precise microwave and RF industry specifications. Connectors in the SMB series are manufactured in jack or plug gender with 50 Ohm impedance. SMB connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SMB connector designs include clamp/solder, crimp/solder or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this SMB connector series is in-stock. Not only in stock, but these connectors will ship the same day as they are purchased.
-
DAS-429PCMCIA/RT10 -
Excalibur Systems, Inc.
Both cards contain 68 Kbytes of true dual-port RAM, for data blocks, control registers and Look-up table, mapped within the Common Memory space. The card also contains a FLASH-based Card Information Structure (CIS) within the Attribute Memory space.The cards comply with the Personal Computer Memory Card International Association (PCMCIA Release 2.1) standard, including Plug and Play. The card's small size and suitability for PCMCIA compatible notebook computers with Type II and Type III slots make it a complete solution for developing and testing ARINC-429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The cards are supplied with C drivers, including source code, Mystic Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
TP800110 -
Total Phase Inc.
The Total Phase Advanced Cable Tester v2 is the quickest and most convenient way to comprehensively test USB, Lightning, and video cables. It provides:*Short testing - Dynamic visualization of test results*Open testing - Dynamic visualization of test results*Continuity testing - Dynamic visualization of test results*DC resistance measurement for most wires, with milliohm precision on ground and power wires, ohm resolution on most other wires, continuity check only on high-speed data lines*Signal integrity testing of data lines to 12.8 Gbps per channel*E-Marker verification*Lightning plug bring up/function (Apple Lightning Cables)**Over-voltage protection (Apple Lightning Cables)**Voltage recovery testing (Apple Lightning Cables)**Quiescent current consumption (Apple Lightning Cables)*
-
781425-01 -
NI
1‑Slot, USB CompactDAQ Chassis - The cDAQ‑9171 is a bus‑powered, CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9171 also has four 32‑bit general-purpose counters/timers that you can access through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
SPA-2-4X22-WDM EYDFA -
Hangzhou Softel Optic Co., Ltd.
*Single/dual input for choice, built in optical switch for dual input, the switching power can be set by the button in the front panel or by web SNMP.*Output adjustable by buttons in the front panel or web SNMP, the range is down 4dBm*Maintenance function of one-time downward attenuation of 6dBm by buttons in the front panel or web SNMP, to facilitate the optical fiber hot-plug operation without turn off the device*Multi- ports output, can built in 1310/1490/1550WDM.*Standard RJ 45 port for remote control, we can provide output contract and web manager for choice, and also plug-in SNMP hardware can be reserved for update.*With laser key to turn on/off the laser.*With RF test function.*Adopts JDSU or Oclaro Pump laser*Led displays the working condition of the machine*Dual power hot plug power supply for choice, 90V~250V AC or -48V DC
-
SOA1550-32(64) -
Hangzhou Softel Optic Co., Ltd.
*Single/dual input for choice, built in optical switch for dual input, the switching power can be set by the button in the front panel or by web SNMP.*Output adjustable by buttons in the front panel or web SNMP, the range is down 4dBm*Maintenance function of one-time downward attenuation of 6dBm by buttons in the front panel or web SNMP, to facilitate the optical fiber hot-plug operation without turn off the device*Multi- ports output, can built in 1310/1490/1550WDM.*Standard RJ 45 port for remote control, we can provide output contract and web manager for choice, and also plug-in SNMP hardware can be reserved for update.*With laser key to turn on/off the laser.*With RF test function.*Adopts JDSU or Oclaro Pump laser*Led displays the working condition of the machine*Dual power hot plug power supply for choice, 90V~250V AC or -48V DC
-
Extech CO230 -
Extech Instruments Corporation
The CO230 measures Carbon Dioxide (CO2), Air Temperature and Humidity, plus calculates Dew Point and Wet Bulb. Features Automatic Baseline Calibration (ABC) with disable for use in areas with continuously elevated CO2 levels. Its alarm function with user settable high/low CO2 level is perfect for monitoring air quality and ensuring proper air ventilation in conference rooms, schools, greenhouses, factories, hotels, hospitals and anywhere that high levels of carbon dioxide are generated. The CO230 also calculates Dew Point and Wet Bulb values, Min/Max CO2 value recall function, statistical weighted averages of TWA (8 hour Time Weighted Average) and STEL (15 minute Short Term Exposure Limit), Alarm relay output for ventilation control and wall mount. Complete with Universal AC adaptor and multiple plug types (US, EU, UK, AUS).
-
Pasternack Enterprises, Inc.
Pasternack 75 Ohm MCX connector category includes several part numbers, the majority are RoHS and REACH compliant. 75 Ohm MCX connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These 75 Ohm MCX connectors are built to precise RF and microwave industry specifications. MCX 75 Ohm connectors are available in jack or plug gender with 75 Ohm impedance. 75 Ohm MCX connector products are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm MCX connector designs include crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this MCX connector series for 75 Ohm is in-stock. Not only are they in stock, these MCX 75 Ohm connectors will ship the same day as purchased.