Showing results: 166 - 180 of 577 items found.
-
esi SR1030 Series -
IET Labs
The esi SR1030 transfer standards consist of 12 equal steps. These steps are available in increments of 1 (SR1030-1), 10 (SR1030-10), 100 (SR1030-100), 1k (SR1030-1k), 10k (SR1030-10k) and 100k (SR1030-100k). The esi SR1030 provides four-terminal connections for each step or for series and parallel combinations of these resistance steps using the optional Series-Parallel (SPC102), Parallel Compensation Networks (PC101) and shorting bars (SB103). This improves power dissipation, stability and errors due to variance in temperature. The esi SR1010 and esi SR1030 are used for the same applications and are alike in configuration. The esi SR1030 differs from the esi SR1010 in that it is specially sealed, and values below 100 k are filled with oil to improve changes due to thermal variations.
-
WGQ-60 -
Shanghai Dean Electrical Co., Ltd
Executive standard: NEMA、JIS; Inspection standard: JB/T4279.15-2008Used to detect the scraping resistance of coating and cable insulation layer of flat wires of 0.800~5.600mm (narrow side) and the silk and enamel covered round wires with nominal conductor diameter of 0.100~5.000mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Sample support table allows for parallel rise and fall, maintaining close contact between the entire plane with sample;Scratching needle is vertical to the paint scraping direction and parallel with sample supporting table;When film is scratched and the action current is ≥5mA, painting scraper would automatically stop scraping;LED would automatically display the number of scraping.
-
Xeltek
SuperBOT is an automatic IC programmer with high performance and reasonable price for large-scale electronic product manufacturing. This programmer can automatically pick up, place, program, take out and pack up chips. SuperBOT 3 is capable of supporting most MCU, CPLD, serial and parallel NOR/NAND FLASH.
-
UTG-1500 -
Phase II Plus
The new PHASE II UTG-1500 is a hand held microprocessor controlled ultrasonic thickness gauge specifically designed for measuring the thickness of metallic and non-metallic materials such as aluminum, titanium, plastics, ceramics, glass and any other good ultrasonic wave-conductor as long as it has parallel top and bottom surfaces.
-
Keysight Technologies
Reduce your cost-of-test up to 20% with our ultra-fast CPU Overcome your process test challenges Boost measurement throughput and lower costs with our synchronous/asynchronous parallel test capability Better low-level measurement performance Create customized waveforms Reduce transition costs
-
N8761A -
Keysight Technologies
The Keysight N8761A is a 300V, 17A, 5100W, single output power supply in a small 2U package. It offers flexible AC input options, analog/resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage respectively.
-
N8754A -
Keysight Technologies
The Keysight N8754A is a 20V, 250A, 5000W, single output power supply in a small 2U package. It offers flexible AC input options, analog/resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage respectively.
-
PCI-DIO Series 24 and 48 -
Acces I/O Products, Inc.
The PCI-DIO-48/48S, PCI-DIO-48JP/JPS, PCI-DIO-48JPL/JPLS, PCI-DIO-48H/HS and PCI-DIO-24S are 24- and 48-bit parallel digital input/output cards designed for use in PCI-Bus computers. The card is 6.9 inches (175 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
QuantumLeap -
Imperas Software Ltd.
QuantumLeap is a parallel simulation performance accelerator that leverages a new synchronization algorithm to provide the fastest virtual platform software execution speed available. The execution performance of this new technology has been measured on average at 15 times faster than the nearest commercial solution using standard benchmarks.
-
MultiDimension Technology Co.,Ltd.
Linear sensor utilizes a unique push-pull half bridge composed of four unshielded TMR sensor elements. The unique bridge design provides a high sensitivity signal output that is linearly proportional to a magnetic field applied parallel to the surface of the sensor package, and it provides superior temperature compensation of the output.
-
PEC N.V.
This product range offers 45V, 100V and 150V systems, with a 60A per channel capability. All systems support parallel switching for achieving higher currents. Each channel has an onboard CAN-bus connection for BMS interfacing and can be extended with auxiliary IO’s for single cell voltage and temperature measurements.
-
Teledyne Paradise Datacom
The Outdoor PowerMAX system maintains complete parallel redundancy down to the embedded control level. Therefore the loss of an entire amplifier will not interrupt remote communications with the system. Remote communications can be either RS-485 or Ethernet.The system will automatically correct its gain level in the event of one or more amplifier failures.
-
HPERC-KBL-MC -
ADLINK Technology Inc.
Inside the tiny footprint of ADLINK’s HPERC lives the power of Intel® Xeon® processor and optional GPGPU parallel processing engine based on a NVIDIA Quadro MXM module. Dual removable secure erase RAID-0 SSDs provide 12Gb/s throughput and security for deployment in hostile environments.
-
D9010AGGC -
Keysight Technologies
The D9010AGGC compliance test software license provides the capability to offload the measurements from the compliance test software running on an oscilloscope to one or multiple virtual machines or measurement servers. This allows you to perform continuous data acquisition and computation of tests result in parallel, reducing the overall test time.
-
55283A -
Keysight Technologies
The Keysight 55283A Straightness Measurement Kit, used with the Keysight 5530 Laser Calibration System, makes straightness, squareness and parallelism measurements to identify geometry errors that seriously degrade machine tool performance. These measurements allow documentation, analysis and diagnosis of machine tool travel and parallel axes of motion.