Showing results: 541 - 555 of 577 items found.
-
id150 SERIES -
ID Quantique SA
Intended for large-volume OEM applications, the id150-1x8 is the only multichannel solid-state single photon detector on the market. It consists of a CMOS silicon chip packaged in a standard TO8-16pin header with a transparent window cap. The chip combines 8 in-line single photon avalanche diodes that can be accessed simultaneously for parallel processing. square in center-to-center A fast active quenching circuit is integrated within each pixel in order to operate each diode in photon counting regime. The chip is mounted on a printed circuit board on top of a single-stage thermoelectric cooler (TEC). A thermistor can be used to measure the temperature of the chip. Only two low power supplies of +5V and -25V are needed for operation in photon counting mode. The fast active quenching circuit leads to a dead time of less than 50ns per channel. An outstanding timing resolution of less than 60ps allows high accuracy measurements.
-
PCIe-9814 -
ADLINK Technology Inc.
The ADLINK PCIe-9814 is a PCI Express digitizer providing speedy, high quality data acquisition. Each of the four input channels supports up to 80MS/s sampling, with 12-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no inter channel phase delay. The extremely large on-board memory enables long recording times even at the highest sampling rates.Unlike parallel PCI buses, PCI Express slots utilize serial point-to-point connection. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9814, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card. The ADLINK PCIe-9814 x4 digitizer can be used in any standard PCI Express slot, x4, x8, or x16.
-
FV1000 -
Becker & Hickl GmbH
*Two Fully Parallel TCSPC FLIM Channels*Compact bh Simple-Tau or Power-Tau System*Two HPM-100-40 GaAsP Hybrid Detectors*Optional: HPM-100-06 Hybrid Detectors, IRF Width < 20 ps FWHM*Optional: HPM-100-50 Hybrid Detectors for NIR FLIM*Optional: Multi-Wavelength FLIM*Excitation by bh ps Diode Lasers*Excellent Time Resolution: Electrical IRF Width 6.5 ps FWHM*Time Channel Width Down to 813 fs*Megapixel FLIM, Up to 2048 x 2048 Pixels at 256 Time Channels*Simultaneous FLIM/PLIM*Detection Wavelength Range from 360 nm to 900 nm*Excitation by Ti:Sa Laser, OPO, or by bh ps Diode Lasers*Systems for Multiphoton FLIM and Confocal FLIM*Systems are Modular: More FLIM Channels can be Added
-
End-of-line Tester UTP 9010 RF -
NOFFZ Computer Technik GmbH
The UTP Series 9010 is a scalable test series available in a variety of feature-rich variants and many designs. The UTP 9010 RF function tester shown here as an example is suitable for tests with a medium number of channels and complexity. It is designed for parallel testing of two or more test items. The measuring instruments used are used alternately for several test items. Due to its compact design and construction as a modular system, this powerful tester can easily be expanded to larger numbers of channels.The integrated HF test chamber UTP 5070 developed by NOFFZ allows an independent shielded test. It can be operated manually or fully automatically by a robot .The basic version of the UTP 9010 series is an ideal system for functional and end-of-line tests and is already preconfigured for this purpose. The RF tester presented in the example is used in particular to test infotainment and eCall modules in the vehicle as well as IoT products with wireless technologies.
-
PCI-7296/7248/7224 -
ADLINK Technology Inc.
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
PCIe-7248/7296 -
ADLINK Technology Inc.
ADLINK"s PCIe-7248/7296 are high-density parallel digital I/O boards with 96/48 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCIe-7248/7296 can utilize the Opto-22 external devices. The PCIe-7248/7296 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCIe-7248/7296 provides 4/2 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCIe-7248/7296 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCIe-7248/7296 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
KT RFCT 2400 -
Konrad Technologies GmbH
The low price point creates a cost effective means for testing wireless communication units, while generating a favorable cost to performance ratio.The calibrated RF test system has a small footprint, integrating seamlessly into test system infrastructures via a single Ethernet connection. GPIOs control the DUT and peripherals. The test system enables communication interfaces like SPI, I2C, UART and CAN. Simple Go/No-Go tests can be performed in parallel. The KT-RFCT 2400A features a 70 MHz to 6 GHz frequency range and includes non-signaling and signaling connections. Bluetooth signaling standards are supported up to 4.1 as well as BT-LE. WIFI signaling standards supported are a, b, g, n and ac.The KT-RFCT 2400A is the perfect test system for a wide range of applications, such as Bluetooth, Infotainment, Keyless Entry, Tire Pressure Measurement, GPS and WIFI.
-
Scienscope
Our SSZ-II Series is one of our most sought after trinocular microscopes. This stereo zoom microscope is true trinocular, durable, cost effective, and low maintenance, as well as an optical zoom range of 2x – 180x with options and a video zoom range of 7x – 628x with options. The NZ Series is also true trinocular, precision optics, medical device standard, and a sealed body, along with an optical zoom range of 4x – 200x with options and video zoom range of 11x – 279x with options.Our parallel zoom trinocular systems, or our E-Series, are also a true trinocular, as well as being ergonomic, low maintenance, having the most accessories available, and being completely customizable. In addition, this trinocular microscope has high performance optics, with an optical zoom range of 4x – 480x with options and a video zoom range from 14x – 558x with options.
-
EN 60601 -
LXinstruments GmbH
Test system for electrical safety compliance testing of medical products in accordance with EN 60601-1, 3rd edition.The system is equipped with three test fixtures which are connected in parallel order to reduce the number of setup tasks for different variants in the course of day-to-day manufacturing processes. Its purpose is to test medical products, e. g. patient monitors, which are employed at hospitals to monitor heartbeat and oxygen saturation.Based on the integrated electrical safety tester by Associated Research, in combination with an AC power source and a switching matrix, it is possible to fully automate tests like for instance AC/DC high-voltage tests, insulation resistance measurements, earth connection tests and leakage current measurements.The required occupational safety is provided by a high-voltage safety hood in accordance with EN 501191. The entire safety technology, as well as the control PC, is mounted in an aluminum-profile cart.
-
PCR-LE Series -
Kikusui Electronics Corp.
The PCR-LE Series is a new line of advanced multifunctional AC power supply that has been developed from our PCR-L/LA Series (linear amplifier type). The PCR-LE Series provides high reliability and can be applied to various applications, by taking advantage of the features that can control broadband waveform freely. Moreover, the PCR-LE Series can be configured as a core device of a test system combined with E-loads and Power Analyzers for “Grid Connection Testing” in regard to dispersed power generation, such as Solar Power, Wind Power, Fuel Cell, and Gas Engine referred to as “New Energy Field”. With various options, the low frequency immunity test and various power enviroment tests are supported. The options for parallel operation and three-phase operation enable you to expand a single-phase system up-to 27kVA, single-phase three wires up-to 54kVA, and a three-phase system up to 81kVA. The system can be applied to a large-scale EMC site for testing of industrial high-capacity air conditioners.
-
ATE-1 -
Lisun Electronics Inc.
Test series connection, parallel connection and series/parallel connections of the electronic ballast (about 15 kinds of connections), available for various electronic ballast. • With a precise resistance box, tube is substituted for the resistance, can act as many as 6 tubes. Resistance value: 1-4095Ω adjustable. • Measure input parameters (vrms, irms, w, pf, harmonics, etc), output parameters (on-circuit voltage, lamp voltage, filament voltage, lamp current, lamp power, oscillatory frequency), can also test the ballast efficiency, abnormity protection, and power symmetry of partial rectifier effect and etc. • Program controlled AC power source to guarantee the smart choice of input voltage and the frequency. • Equipped with 17 inch LCD controlled machine, specially designed A/D combined with special CPU, has the two left and right testing interfaces to achieve stability of data and high- speed testing. • We can make the special-designed product for you and promise to upgrade the software for free.
-
PI-1600 -
ETI Precision
The PI-1600 Circuit Breaker Tester incorporates modular design and flexibility to provide unequaled capability in a portable package. The PI-1600 test set is two testers in one, incorporating the PI-800 and PI-AUX. The PI-800 section can be used alone, on 120 or 240 VAC supplies, generating continuous current of 400, 800, amps at 4.2 kVA, with peak output to over 10x. When configured for the PI-1600, the PI-AUX output unit is connected in series or parallel to the PI-800. The PI-AUX boosts total power to 9.8KVA, and allows testing of draw-out breakers and MCB’s to 1600 Amps. The units are housed in rugged interlocking suitcase-size enclosures. Each piece weighs no more than 125 pounds, allowing one-person hand truck mobility. Basic operation is very simple, and the proven MAC-21 control instrumentation provides optimal output control and measurement. The MAC-21 instrumentation is supplied in a separate rugged portable case, interlocks on top of the PI-800, and connects to a cable in the rear of the test set.
-
Sinowon Innovation Metrology Manufacture Ltd.
◆ The lifting system adopts linear guide rail and precision screw drive, which makes the lift drive more comfortable and stable;◆ With precision toothless rod and fast movement locking device, ensure return error is within 2um;◆ High accuracy A optical scale and precision working stage, ensure machine accuracy is within 3+L/200 um;◆ HD zoom lens and HD color digital camera, ensure clear image without distortion;◆ With programmable surface 4-ring 8-division LED cold light and contour LED parallel illumination, it can control the brightness of the 4-ring 8-division independently;◆ With powerful iMeasuring2.1 software system , to enhance the control quality;◆ Optional imported contact probes and 3D measuring software, it can help upgrade the machine to be coordinate measuring machine;◆ Optional FexQMS measurement data analysis and real-time monitor software, enhance process control, reduce material consumption;
-
JT 2147 QuadPOD -
JTAG Technologies Inc.
The JT 2147 QuadPOD high speed device programmer and flash programmer comprises JT 2148 transceiver and four independent, programmable JT 2149 TAP PODs and provides signal conditioning for the DataBlaster series of boundary-scan controllers. Used for gang, parallel, fast testing / Programming of devices.TAP pods can be housed integrally within the transceiver or they can be detached and reconnected via the (optional) one meter extension cable. The JT 2148 transceiver is available in standard (/10) or industrial (/13) variants. The /13 variant includes a SCSI cable splitter to allow system integrators to use flat ribbon cables into the transceiver itself which often simplifies fixture building.A fixture-embedded variant of the JT 2147 is available as part reference JT 2147/FXT. This unit integrates the function of the transceiver and four pod onto a single assembly. This variant can also support 64 DIOS channels and SCIL functions (see more images below for a picture of the JT 2147/FXT).
-
N1231B -
Keysight Technologies
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
