Showing results: 2686 - 2700 of 6572 items found.
-
A009DM5-T-HA200 -
Pickering Interfaces Ltd.
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
064-474 -
ELMA Electronic, Inc.
Hold-Up power module for voltage inputs from 16 to 36VDC provides up to 330W of hold-up power for 50ms. Designed in compliance with MIL-STD-704 / DO160. The board can be ordered as a fixed mount or plug-in version.
-
JYV-40 -
Kingrun Instrument Co., Ltd.
JYV-40 segment voltage test equipment is made up of constant current source, voltage-checking circuit and control circuit. The output current is adjustable and stable. Measured voltage value can be shown by three and half digital voltmeter, it can test the DC interturn and segment voltage and also is the effective way of checking turn coil resistance equilibrium.
-
BTD-34 -
Hutz Auto & Air Nanjing Ltd.
Battery Load Tester LED Digital , Capacity of battery:36Ah~160Ah, Rated test voltage:12 v, Voltage accuracy:+/- 0.1 v, Test cycle:10 seconds
-
BTD-26 -
Hutz Auto & Air Nanjing Ltd.
Battery Load Tester LED Digital , Capacity of battery:160 AH, Rated test voltage:12 v, Voltage accuracy:+/- 0.2 v, Test cycle:10 seconds
-
BTD-21 -
Hutz Auto & Air Nanjing Ltd.
Battery Load Tester LED Digital , Capacity of battery:160 AH, Rated test voltage:12 v, Voltage accuracy:+/- 0.2 v, Test cycle:10 seconds
-
BTD-31 -
Hutz Auto & Air Nanjing Ltd.
Battery Load Tester LED Digital , Capacity of battery:36Ah~160Ah, Rated test voltage:12 v, Voltage accuracy:+/- 0.1 v, Test cycle:10 seconds
-
Texas Instruments
voltage-output, current-sensing amplifier family that integrates an internal shunt resistor to enable high-accuracy current measurements at common-mode voltages that can vary from 0 V to 36 V, independent of the supply voltage. The device is a bidirectional, low- or high-side current-shunt monitor that allows an external reference to be used to measure current flowing in both directions through the internal current-sensing resistor sensor. The integration of the precision current-sensing resistor provides calibration equivalent measurement accuracy with ultra-low temperature drift performance and ensures an optimized Kelvin layout for the sensing resistor is always obtained.
-
Osborne Transformer Corp.
Osborne DC filter inductors (aka filter chokes) are commonly used in AC to DC conversion circuits to present an inductive voltage drop to the AC component of rectified current. This inductive voltage drop acts as a filter. Osborne designs filter inductors to components to function effectively (without saturation) in the presence of the DC current. Osborne will work with you to mitigate the impact of ripple frequency in conversion circuits. Every Osborne DC filter choke is designed for high performance with special consideration given to your circuit´s power supply frequency and conversion configuration.
-
LS2010 -
Lisun Electronics Inc.
• Measure Vrms, lrms, W, PF, Hz; • Harmonic distortion analysis for voltage & current, display total harmonic and 0-50 times; • Component harmonic, selectable for absolutely or relatively harmonic display; • Voltage range: 10.0-600.0V, Current range: 0.010-20.00A, Auto range; • Accuracy: ± (0.4%reading + 0.1%range + 1digit); • Simultaneously display Vrms, lrms, W, PF value on 4 windows, suitable for production line; • Can test every kinds of curve; Print both data & curve; • Communication port for PC, run under WinXP or Win7.
-
Datexel
The DAT4530 can convert any process signal (Thermocouples, RTD, mV, Voltage, mA Resistance and Potentiometer) to a voltage or current output (4-20mA, 0-20mA or 0-10V). Each output can be different and it also has a built in limit alarm which is an SPST relay. The DAT4530 is PC programmable with the aid of the Prodat programmer and the Datasoft software which is available from the Datexel down load page. The DAT4530 is also programmable with the aid of 3 DIP switches which can be found on the side of the DAT4530. There is full isolation between the input, power supply, limit alarm output and two outputs.
-
Junction Measurement and Analysis -
Materials Development Corporation
A comprehensive set of analyses for junction diode or Schottky barriers begins with C-V data gathering that adjusts the voltage step to the slope of the C-V characteristics. This assures an optimum set of C-Vdata whether the voltage range is small or large. Doping profile and resistivity profile are both available at the touch of a key. Plots of 1/C2 - V or Log(C) - Log (V+ phi) show doping uniformity and doping slope factor. Exclusive recalculation options allow adjustment of stray capacitance and area to facilitate calibration using a standard reference wafer of known doping or resistivity.
-
PE42512 -
pSemi Corp.
The PE42512 is a HaRP™ technology-enhanced absorptive SP12T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42512 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
PE42562 -
pSemi Corp.
The PE42562 is a HaRP™ technology-enhanced absorptive SP6T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42562 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
PE42582 -
pSemi Corp.
The PE42582 is a HaRP™ technology-enhanced absorptive SP8T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42582 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.