Showing results: 3781 - 3795 of 6572 items found.
-
QA350 -
QuantAsylum
The QA350 relies on a built-in reference to calibrate the ratio between the hi and low ranges. If you have a preferred lab reference, you may use that it to improve the QA350 accuracy beyond the indicated +/- 400 PPM. For example, various vendors on eBay can provide calibrated +/-30 PPM 5 or 10V voltage references that can be used to set the ultimate accuracy of the QA350 to under 50 PPM at room temperature.
-
Texas Co.
Probes connect the input of the oscilloscope to test points on the device under test (DUT). There are many types, including: high impedance passive, low capacitance, single-ended active, differential active, high voltage, and current probes. This is the first in a series of three articles on probe selection and application, and will focus on passive probes. Part 2 and part 3 will address active probes and current probes, respectively.
-
PS401-HRP -
Axiomtek Co., Ltd.
*Input Range: 90 ~ 264Vac Full Range*Output Voltage:**+5V, 35A (5A min)**+3.3V, 28A (1A min)**+12V, 20A (2.5A min)**-12V, 1A**-5V, 0.8A**+5Vsb, 2A (0.1A min)*MTBF(hours): 100,000h*Safety: UL, TUV, CE, CSA*Dimensions: 183 x 167 x 187.8 mm*Compatible with Axiomtek products: AX61492
-
AC-DC Dual Tracking Outputs -
Acopian Technical Company
Although small in size, these mini-modules offer high performance at modest prices. They provide the voltages commonly required for driving op amps and other balanced loads and may be mounted in an area only 3.5" x 2.5". Terminal strip input/output connections eliminate all need for sockets or soldering. Short circuit protection, encapsulated construction, and conservative design assure long term reliability.
-
Edmund Optics Inc.
These avalanche photodiodes (APDs) are silicon photodiodes with an internal gain mechanism. As with a conventional photodiode, absorption of incident photons creates electron-hole pairs. A high reverse bias voltage creates a strong internal electric field, which accelerates the electrons through the silicon crystal lattice and produces secondary electrons by impact ionization. The resulting electron avalanche can produce gain factors up to several hundred.
-
Part No. LPBD100 -
Teledyne Defense Electronics Relays & Coax Switch
The LPBD100 is a dual-output 100 Vdc plastic relay. The relay output-switch contacts are normally closed and will conduct the load current until a voltage is applied to the relay input. With 4 volts or more at the relay input, the output-switch contacts open and the relay no longer conducts. The LPBD100 assembly contains two independent, completely isolated relays.MSL 6 Available options include:LPBD100 0.25Adc, 100Vdc Load; 4-7Vdc Control;
-
CryoTel® Generation II Controller -
Sunpower Inc.
The Generation II Controller is backward compatible with Generation I, so any setups which are communicating with Sunpower’s Generation I Controller will work with the new controller. Users switching from Generation I to Generation II may need to increase the DC voltage to the controller 1-2 volts to match the maximum power they attained with the Generation I Controller. The mass of the Generation II Controller is 490 grams.
-
MFG-8203 -
MCH Instruments Co.,Ltd.
Features:*Low distortion, high stability*Linear and logarithmic sweep function*Sweep time and width adjustable*External voltage control frequency (VCF)*Internal& external modulation AM/FM with modulation control*Output signal compatible with TTL/CMOS*Seven types of waveforms such as sine, square, triangle and ramp*DC power output attenuation can be applied to main output signal*Built-in frequency meter:0.1Hz-30Mhz
-
CPCI395 -
AcQ Inducom
The CPCI395 features 16 analog voltage outputs, integrated on the CompactPCI standard. Each output has a 12- or 16-bit resolution and a software programmable output range (0..+10V or -10..+10V). Control of the analog output is as easy as writing the binary equivalent to a dedicated register (per channel). Conversion takes place automatically. If desired, channels can be synchronized by presetting the channels and then give a simultaneous update command.
-
HSL-DO32-M-N/HSL-DO32-M-P -
ADLINK Technology Inc.
Slave ID consumption: 2 consecutive from odd"N" type for NPN sinking type outputSwitch capacity: Single channel 500 mA; all channels 60 mA at 24VDCPhoto couple isolation voltage: 2500 VrmsResponse time: ON→OFF: 180µs, OFF→ON :1.2µsLED indicator: Power, Link and Output statusPower supply: +10V to +30 VDCOperating temperature: 0 to 60°C
-
TMD Technologies Ltd
Fully integrated microwave tubeHigh voltage switched mode power supplyBuilt in test electronics (BITE)Designed for the harshest environments – strong, sturdy, robust, MIL SpecHigh reliability – all products fully ESS tested before shipmentHigh level of customer support worldwideHigh level of product innovation – TMD won a Queen’s Award for innovation in 2005 for a low noise radar power supply design
-
Analog Devices Inc.
Analog Devices provides a portfolio of quad resistor networks with excellent matching specifications over the entire temperature range. All of our resistors can be accessed and biased independently, making them a convenient and versatile choice for any application that can benefit from matched resistors. Our resistor networks provide the precise ratiometric stability required in highly accurate difference amplifiers, voltage references, and bridge circuits.
-
WFG-110 -
Wuntronic GmbH
The Model WFG-120 System is a complete 3 axis fluxgate magnetometer packaged in a rectangular/parallelpiped package of dimensions 0.75\" x 0.75\" x 2.75\". The package corners are rounded to enable the unit to fit inside a 1.0\" diameter cylinder. The system operates from one of two optional input voltages: regulated ±5 VDC or unregulated ±7 to ±12VDC and consumes a total power of 200 mW.
-
WFG-120 -
Wuntronic GmbH
The Model WFG-120 System is a complete 3 axis fluxgate magnetometer packaged in a rectangular/parallelpiped package of dimensions 0.75\" x 0.75\" x 2.75\". The package corners are rounded to enable the unit to fit inside a 1.0\" diameter cylinder. The system operates from one of two optional input voltages: regulated ±5 VDC or unregulated ±7 to ±12VDC and consumes a total power of 200 mW.
-
40-967-160-F -
Pickering Interfaces Ltd.
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination and provide a suitable method of restraining the cables. Pickering cable assemblies for this product are contained elsewhere in this data sheet. Interfacing PCB?s should be designed with suitable clearances for the voltage the application requires.