Showing results: 196 - 210 of 464 items found.
-
M.2 Gen4 Socket2 -
SCHILLER AUTOMATION GmbH & Co. KG
The PCIe Gen4 M.2 Socket 2 test adapter or test fixture kit facilitates Device and Host compliance testing for PCIe Gen4 M.2 Socket 2 Source and Sink devices.
-
PeakTech Prüf- und Messtechnik GmbH
This innovative combination measuring device for testing electrical installations according to official laws convinces with its technical performance data in the high-end area. All important safety tests such as FI, voltage, loop, low-resistance, earth resistance and insulation tests for e-checks and new installations can be carried out safely by the electrician via the large 3.5“ TFT color display. Of course, the device comes with an extensive range of accessories, such as all necessary test leads, adapters, rods and the required software CD for the PC. The device can be charged with a power adapter or via a car adapter. During the daily use, this high-quality device is protected against dust and all-round water jets by its protection class IP 65.
-
VDE 0100 -
PeakTech Prüf- und Messtechnik GmbH
This innovative combination measuring device for testing electrical installations according to official laws convinces with its technical performance data in the high-end area. All important safety tests such as FI, voltage, loop, low-resistance, earth resistance and insulation tests for e-checks and new installations can be carried out safely by the electrician via the large 3.5“ TFT color display. Of course, the device comes with an extensive range of accessories, such as all necessary test leads, adapters, rods and the required software CD for the PC. The device can be charged with a power adapter or via a car adapter. During the daily use, this high-quality device is protected against dust and all-round water jets by its protection class IP 65.
-
DMX ADAPTER -
EMO Systems Canford Audio PLC
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
MCVK -
Matco Tools
*Tests compression on all domestic and import cars and trucks with gasoline engines*Compression tester kit includes: 2-1/2" gauge with dual inch/metric readings: 0-300 psi and 0 to 21 kg/cm2, 14mm/18mm solid short adapter, 14mm/18mm long flexible adapter and 14mm long reach adapter*Checks vacuum and fuel pump pressure and locates air leaks in fuel lines, vacuum operated chokes and emission control systems on all domestic and import cars and trucks with gasoline engines
-
34000 -
S & G Tool Aid Corp
Test compression on all domestic and foreign cars and most trucks. Adapters fit vehicles with 14mm and 18mm plugs including long reach and 5/8" hex plugs. Flex hose eliminates need to remove auxiliary equipment such as power brakes and steering, air conditioning and manifold. Screw in adapters guarantee accuracy over push-in type testers. Quick side release valve permits retest without removal of adapters. Gage ranges 0-300 PSI and 0-21 BAR. Supplied in storage pouch.
-
PCI EmbeddedComputer Systems
This adapter can be used to run, test or program a 3U VPX card in a standard PC PCIe slot. SSC switchable (ON/OFF) PCs available from PCI-Systems Inc.
-
TOPTEST GmbH
Development of additional hardware components in-houseCreation of the layout of the developed circuit boards and subsequent production outside the companyAssembly of the printed circuit boardsCreation of additional circuits for test adapters
-
34729 -
S & G Tool Aid Corp
Makes for easier diesel compression testing in areas with restricted clearance. Attaches between Cat. No. 34700, Diesel Compression Tester and Tool Aid brand diesel test adapters.
-
FIT13APB -
Matco Tools
This basic fuel injection tester includes large and small Schrader adapters, M6-1.00 O-ring adapter, and tee manifoldIncludes everything necessary to test the following systems: American Motors; Bosch AFC, MPC European and Japanese (except CIS- use our FIT447); Chrysler Corporation; Ford Motor Company; GM (except TBI- use our FIT446)
-
1110748 -
Aries
Surface Mount to DIP Adapter for SOT-25, SOT-23A-6. Allows for breadboarding or substitution of microgate SOT-23A-6 and SOT-25 IC and transistor packages into .100 [2.54] pitch proto boards or PC boards. Solder masked top-side pads allow user to hand solder devices directly to topside of adapter with fewer problems of solder bridging. Longer male bottom pins are available at special request for easy use of probe clips. Large topside pads allow for soldering test pins, jumpers, etc. to top of adapter.
-
196275-01 -
NI
The SHC68-C68-D4, 1m, Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
781293-01 -
NI
The SHC68-C68-D4, 2m, Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
69600 -
Lisle Corp.
Kit includes 14 flexible test probes, long straight probe, piercing back probe, crocodile clip, 4mm circuit tester adapter and Deutsch spooned probe. The probes are designed to be used on popular Weather-Pack, Metri-Pack and Micro-Pack style connectors. The test probes are 5" in length and are flexible to help eliminate damage to the connector terminals that can result from testing with a standard test probe. The 4mm adapter allows conversion of some circuit testers to a 4mm banana connector, which provides a better connection. Kit comes in a pouch for storage.
-
Hyperlabs, Inc.
HYPERLABS Controlled Impedance Analyzers can be used with various probes and adapters to quickly and reliably characterize impedance on PCB test coupons. These Test Systems are designed to comply with IPC-2141A standards for PCB coupon testing, and can be customized to meet specific customer needs.