Showing results: 196 - 210 of 240 items found.
-
9940 -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai Optical node is the earliest manufacturing that adopts AUGAT aluminum die-casting to make 4 ports optical communication platform. The platform is gradable and has become the main device that widen HFC subscribers access network. It is widely used in FTTB, FTTC. Its RF output is driven by one power-doubling module. It can be installed with 2 receivers, 4 transmitters and 2 power supplies (main and back-up ), which can improve the system redundancy.
-
Optoplex Corporation
These high speed photodiode, PD-200, is hermetically sealed, high reliability, low harmonic distortion photodiode modules designed for high optical power applications with minimum bandwidths of 20 GHz. The device is well suited for receiver applications with optical pre-amplification, and is available either with or without an internal 50Ω termination. The photodiode module is available in either a V-connector package or a miniature surface mount package with CPW (coplanar waveguide) RF output.
-
Optical Zonu Corp.
Optical Zonu’s RF over Fiber product line contains multiple stand-alone modules which are designed to integrate easily with your application. Each of our stand-alone modules is a Transceiver (TRx), but it may also be configured as individual Transmitter (Tx) or Receiver (Rx) units. A pair of these transceivers creates two-way bidirectional RF to Optical and Optical to RF link. Standard operational frequency ranges between 47 MHz and 3 GHz but can be extended to from 10 KHz to 3.3 GHz. OZ816 and OZ1606 modules have ultra-broadband capability that ranges from 47MHz to 7 GHz.
-
Optoplex Corporation
Targeting for the next-generation 40Gb/s system based on advanced optical differential phase shift keying (DPSK) demodulation, Optoplex’s 40Gb/s Integrated DPSK Receiver (DPSK Rx) demodulates an incoming DPSK optical signal into a pair of differentially (amplitude) modulated RF outputs at data rate up to 43Gb/s in a compact package. Phase modulated optical signals offer much better dispersion performance compared with traditional amplitude modulated counterparts because the carrier light stays on all the time so that the intensity-dependent nonlinear effects in the transmission link are avoided, resulting in longer transmission distances.
-
Appointech, Inc.
The fiber-optic coaxial PIN-TIA receiver module is designed for SONET/SDH fiber-optical communicationnetworks, using reliable InGaAs PIN photodiode (PD) highly integrated with low noise transimpedence amplifier(TIA) to convert a long wavelength input optical signal into a differential (or single) output. It is a highly reliablemodule with excellent performance.
-
L-Band -
QuestTel
QuestTel''s Satellite L-Band optical fiber Transmitter/Receiver set offers high pefromance and cost effective alternative to conventional coaxial systems. The L-Band Transmitter and Receiver pair is used for transporting L-Band RF over fiber from the antenna to the satellite receiver. Additionally transmitter provides optional 13/18V LNB power as well as Automatic Gain Control (AGC) to manage RF input level. By transporting the L-Band RF over fiber this range can be extended from several hundred feet to over 80 miles. Since optical signal is not affected by electromagnetic field, the quality of your signal will always stay at the high level. Also this fiber solution is more cost effective than coaxial system, as well as more reliable and flexible.
-
M8290A -
Keysight Technologies
The M8290A is a flexible solution platform for 400G coherent component and transmitter test. It incorporates a 92 GSa/s modular optical modulation analyzer and a 92 GSa/s 4-channel electrical digitizer. Besides these modules an additional arbitrary waveform generator module up to 92 GSa/s, such as the M8196A, can be added to the same AXIe chassis. This setup results in a compact and flexible coherent test solution that can be used together with additional specialized solution software for Integrated Coherent Receiver (ICR) and Analog Coherent Optical (ACO) module characterization.
-
Optoplex Corporation
To be used for optical coherent detection such as DP-QPSK receivers, Optoplex’s ten-port 2x8 Coherent Mixer (aka QPSK mixer) combines the incoming signal with a local oscillator to generate eight light states in the complex-field space. The eight light output signals can then be coupled into four pairs of balanced detectors. The block diagram below shows the application of a 2x8 coherent mixer in a DP-QPSK receiver. Since the mixing process is data rate independent, the devices can be used for any data rate in applications such as 40Gb/s or 100Gb/s transmission systems.
-
E1708A -
Keysight Technologies
The Keysight E1708A uses an optical fiber to transport the laser beam from a remote sensor assembly to the electronics. This improves measurement accuracy and repeatability by enabling you to mount heat-producing electronics away from the measurement area. The fiber optic cable also provides increased mounting design flexibility and easier access to the receiver attenuation and squelch adjustments.
-
MR30 (30KHz~100GHz) -
Hangzhou Huatai Optic Tech. Co., Ltd.
MR30 series microwave wideband optical receiver, adopts waveguide intergrated PIN photodetector. Within 40KHz~100GHz bandwidth, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. MR30 series PIN photodetector products have unsurpassed high-power handing capability. In system application, they can pre-amplify the received optical power by EDFA, favorable responsibility, with high voltage out, avoiding the need for electrical amplification. They are suitable for testing and application in microwave opto-electronics and high speed lightwave area as well as 40Gb/s (OC-768, STM-256) high-speed communication system.
-
1177A -
Audio Authority Corp.
The 1177A is a unique four input, one output digital audio switcher, incorporating technologies such as AutoSelect automatic input switching and digital audio automatic cross-conversion. This sturdy product is perfect for adding digital audio inputs to a Bose Lifestyle system, or a legacy A/V receiver that has very few digital inputs. Supports both digital optical and digital coaxial audio types.
-
L-1SDI-FE-3G-TX/RX -
QuestTel
The L-1SDI-FE-3G-TX/RX is a SD/HD/3G-SDI over fiber transmitter and receiver extender kit. This unit provides optical transmission of one SD/HD/3G-SDI signal with embedded audio signal and has reversed RS485 data channel for camera control. L-1SDI-FE-3G-TX/RX kit can be used in HD video conference, as well as HD video monitoring, intelligent transportation system and public security system.
-
Cohu, Inc.
For optical sensor test Cohu offers a variety of solutions being driven by requirements for tri-temp, parallelism and stimulus spacing. Customized optical stimulus units are integrated into Cohu’s test handling systems. For light detector test, we implement different types of light sources, such as infrared, ambient- and colored light. We offer different solutions for 3D image sensors combining emitter and receiver tests of LiDAR, Time of Flight and Structured Light devices.
-
LTX-5525 -
Scitec Instruments Ltd
The LTX-5525 conveys sixteen independent channels of digital information over a fibre optic link ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled 100 million times per second, multiplexed and transmitted serially over an optical fiber at two gigabits per second. The receiver acquires this digital data and de-multiplexes it to 16 separate output ports.
-
DP-VME-5838 -
Data Patterns Pvt. Ltd.
The DP- VME-5838 is a VME64x slave, high performance 335M, six channel Digital receiver card. It samples and down converts the analog IF signals into the digital base band data. The processed I/Q data are pulse compressed and decimated to the base band rate. In the Central Unit system, this pulse compressed I/Q data has to be sent to the signal processing unit through a 2.5G speed Optical SFPDP link.
