Showing results: 181 - 195 of 233 items found.
-
ABex REC21-84TE-EXT -
Konrad Technologies GmbH
Robust and flexible interconnect solution for test fixtures. Designed for the use with ABex PXIe Rack 18 it provides support to equip all 21 slots with VPC interconnect modules. In addition, it offers 6 more slots on the bottom, below the ABex rack to feed through signals from external measurement devices.The interface uses the well-known Virginia Panel connectors with more than 20.000 guaranteed mating cycles. To build DUT specific test fixture, we also provide the corresponding ITA mounting frame (ITA = Interchangable Test Adapter).
-
N6782A -
Keysight Technologies
The Keysight N6782A is a source/measure unit (SMU) designed specifically for advanced functional testing of a device. The ability to modulate the output up to 100 kHz along with capability to source and sink current (2-quadrant operation) makes the N6782A a perfect fit for advanced functional test of a variety of devices such as DC/DC converters, power management units, power amplifiers, and power management ICs. The input stage of the DUT can be stimulated by the fast sourcing and waveform capabilities. While the output stage can be loaded down and measured with the electronic load capabilities, providing a total test solution.
-
R&S®SMW200A -
Rohde & Schwarz GmbH & Co. KG
Performance and functionality requirements vary depending on test setup and application. The R&S®SMW200A is unrivaled in mastering this challenge and sets new standards for signal generators. When developing and verifying any type of DUT, including component, module and complete base stations – the R&S®SMW200A always easily generates the appropriate test signals with top performance. The flexible modular design of the R&S®SMW200A can be equipped with the exact options required for specific applications. Any configuration is possible, from a classic single-path vector signal generator to a multichannel MIMO receiver tester.
-
ABex Switching -
Konrad Technologies GmbH
The ABex Switching features a text-based way to connect and disconnect relays on ABex modules. Alias names for channels could be defined in a DUT specific topology file and then be used for text-based switching. These alias names are also shown in the Konrad System Manager allowing easy debugging of test sequences. The ABex Switching functionality could be either used out of NI Teststand with the provided test steps or via API from other programming languages.- Text-based switch routes- XML based topology for Alias mapping- Switch routes with support for Alias names- Seamless integration into Konrad System Manager
-
EIIT, S.A.
New polymers are constantly being developed and component manufacturing techniques appear, allowing the gradual replacement of metallic materials by plastics or composites, in various fields of application, in different industries. In particular, in the air conditioning, heating and water supply sector, plastic components are subject to the aging process due to the temperature to which they are subjected or due to the amount of oxygen in the fluids. The Test System for Longevity and Accelerated Aging Tests developed by Controlar allows to foresee, in accelerated test, the wear throughout the life of the plastic components of the hydraulic systems, in order to prevent eventual failures during the useful life cycle of the DUT.
-
N2796A -
Keysight Technologies
The N2796A is a new generation of low-cost, single-ended active probe with the AutoProbe interface. The probe integrates many of the characteristics needed for today’s general-purpose, high-speed probing - especially in digital system design, component design/characterization, and educational research applications. Its 1MΩ input resistance and extremely low input capacitance (1 pF) provide ultra low loading of the DUT. This, accompanied with superior signal fidelity, makes this probe useful for most of today’s digital logic voltages. And with its wide dynamic range (±8 V) and offset range (±12 V), the probe can be used in a wide variety of applications.
-
N2795A -
Keysight Technologies
The N2795A is a new generation of low-cost, single-ended active probe with the AutoProbe interface. The probe integrates many of the characteristics needed for today’s general-purpose, high-speed probing - especially in digital system design, component design/characterization, and educational research applications. Its 1MΩ input resistance and extremely low input capacitance (1 pF) provide ultra low loading of the DUT. This, accompanied with superior signal fidelity, makes this probe useful for most of today’s digital logic voltages. And with its wide dynamic range (±8 V) and offset range (±8 V), the probe can be used in a wide variety of applications.
-
N1055A -
Keysight Technologies
Bandwidth options: 35 or 50 GHz (upgradable)Edge speed (10-90%, typical): 18 ps (35 GHz) or 7 ps (50 GHz)Channel options: 2 or 4 per module (upgradable) with independent skew control and up to 16 channels per 86100D mainframe Ultra-thin remote head: 1.6 m phase-stable cable, 2.92 mm (35 GHz) or 1.85 mm (50 GHz) connectors, and integrated 67 GHz diode limiters for ESD/EOS protection TDR fixture de-embedding removes effects of fixtures, cables or probes connected between remote heads and DUT
-
N6781A -
Keysight Technologies
The Keysight N6781A is a source / measure unit (SMU) designed specifically for the task of battery drain analysis. Whether the device under test (DUT) is an eBook reader, MP3 player, mobile phone, or pacemaker, the N6781A’s seamless measurement ranging, programmable output resistance, and auxiliary DVM combine the best set of advanced features on the market for battery drain analysis. When used with the 14585A Control and Analysis software, the N6781A becomes an even more powerful battery drain analysis solution, offering additional insights into your measurements. Learn more about the 14585A Control and Analysis software.
-
LXinstruments GmbH
The in-vehicle test set was developed to successively measure several active RF amplifiers installed in the vehicle as well as different antenna structures. It offers the possibility to connect 12 DUTs. The DUTs can be connected to an external spectrum analyser via a 1 to 12 RF multiplexer. Each DUT can be individually switched and supplied with an adjustable voltage via a bias-tee integrated in the system. The individual bias voltages and currents are recorded by the IVTS and can be called up on an interactive control panel or via Ethernet and SCPI commands. The complete system can be powered by rechargeable battery and can be operated either via Ethernet, fibre optics or WLAN.
-
6565 SERIES -
Wayne Kerr Electronics, Ltd.
The 6565 HF DC Bias Unit is intended to be used with a Wayne Kerr 6500 analyzer, either the 6500B Precision Impedance Analyzer or the 6500P HF LCR Meter. Its function is to provide a source of DC bias current through the Device Under Test (DUT) while the analyzer is making AC measurements. Each 6565 unit can provide up to 10 A of DC current, and up to six 6565 units can be connected in parallel to supply a maximum 60 A. A digital ammeter on the front panel allows the user to see the dc bias current value and an indicator LED shows when the bias current is enabled.
-
GX5295 -
Marvin Test Solutions, Inc.
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
GX5295 -
Terotest Systems Ltd.
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
MPI Probe Card Technology
The FCB Probe Card is the most mature technology of buckling beam probe card. It is aimed to achieve the semiconductor ship manufacture time-to-market (TTM) and cost of test (COT) demand. FCB is a proven solution for a variety of semiconductor production tests from early engineering pilot-runs to high volume manufacturing (HVM). FCB is ready for device requiring high signal integrity probing (SI) and/or power integrity probing (PI). Applications include cutting-edge SiPs/SoCs, WLP, graphic processors, micro processor, industrial microcontrollers, and more. FCB guarantees the world’s best overall cost-of-ownership (COO) for various DUT applications.
-
UTP 6010 RF -
NOFFZ Computer Technik GmbH
The UTP 6010 is one of our smallest test systems and therefore a cost-effective entry into our UTP tester series.The fast system is used to implement scalable functional test applications for a test item (single device under test) with multiple RF channels and mixed-signal test options. Depending on the adapter, the DUT can be tested at circuit board level (FKT) or when installed at the end of the line (EOL).Depending on the test item requirements, we configure the appropriate number of channels and integrate the necessary interfaces directly in the adapter or tester. The test speed, production volume and overall complexity of the UTP 6010 interfaces can be varied according to your requirements.
