Showing results: 601 - 615 of 685 items found.
-
EX1629 -
AMETEK VTI Instruments
48-Channel High Performance Strain Gauge Measurement InstrumentSupports quarter-bridge (120, 350Ω or user defined), half-bridge or full-bridge24-bit ADCs, sampling rates up to 25 kSa/sBuilt in programmable differential excitation -8V to 8VBuilt in selectable bridge completionConfigure signal conditioning excitation and bridge completion on a per channel basisSimple, low-cost wiring using RJ-45 telecom connectorsSupports TEDS for easy transducer detection and setupRJ-45 input connector reduces setup cost and timeBuilt in self-calibration and shunt calibrationSupports voltage, ratiometric and linear measurements other than strain measurements.
-
MODEL PSMR -
Transducer Techniques, Inc
The PSM-R is a self contained AC power bridge excitation supply. This device consists of a low interwinding capacitance AC transformer and a high stability adjustable linear regulator designed specifically for driving transducer bridges. DC excitation is adjustable from 4 to 15 volts output and is capable of supplying 0 to 150 mA in output current. It features remote sensing to eliminate line drop errors and very low noise. It can also be used as a high quality voltage source or reference in many applications. AC input requirements are 105 to 125 VAC at 60 Hz.
-
ESI Technology Ltd
ESI Technology manufacture a wide range of pressure sensors using a variety of different technologies. Pressure transducers (voltage output), pressure transmitters (milliamp output), panel meters, accessories. Silicon-on-Sapphire technology and a titanium diaphragm combine to make the new Gold Standard in pressure sensing. Custom pressure measurement solutions have been integral to ESI’s success. All aspects of design and manufacture are done in-house at our UK facility. Impressive quality at an affordable price. So if you don’t see what you are looking for, just ask.
-
9330 -
Interface Inc.
The Model 9330 displays 24-bit resolution and has an impressive 3750Hz update rate. Incorporating peak and valley capture, it can store up to 6 sensor calibrations and measurements from load cells or torque transducers can be logged at 1000Hz to a standard SD card. This data can then be downloaded to a PC via the built-in USB port and Windows compatible software for off-site analysis. Adding further versatility, the rechargeable battery can power up to 4 x 350 ohm sensors, but also offers up to 300 hours stand by time and up to 20 hours continue use.
-
MCA -
Bacharach, Inc.
The Neutronics MCA Multi-Channel Controllers are designed to accept up to 8 inputs. Primarily used with gas detector heads, the MCA controllers will also accept individual inputs from various types of monitoring instruments or transducers. A backlit LED display is provided to show the status of each channel, display graphs, and enable configuration of the unit (set alarm levels, program the output relay voting, etc.). The MCA can be programmed on-site by the user using the password protected configuration program. Each monitoring channel provides relay contact outputs along with 4-20mA and voltage outputs.
-
PVX -
Dakota Ultrasonics
PVX is equipped with an alpha-numeric data logger to provide increased versatility for those custom reporting needs. The high speed scan feature speeds up the inspection process by making 32 measurements per second. Remove transducer from the test material and display the minimum measurement scanned.Visual and audible alarm with hi and lo limit settings for specific application tolerances. Auto find features locates the detection point(s) and adjusts the display settings to bring the waveform into view. PVX comes complete with our Windows PC software for transferring data to and from a PC.
-
M1-25M/XXE -
Elmika
The M1-25M/XXE series instruments are high precision broadband Calorimetric Sensors operating in millimeter and sub-millimeter wave range on a principle of substitution of microwave power by direct current power, using an autocompensating transistor transducer. Calorimetric Sensor is supplied with Calorimetric Power Meter M1-25M (measurement and indicator block), which provides PC connection via USB interface.Calorimetric Power Meter with Calorimetric Sensor provides accurate absolute power measurements in single mode and multimode waveguides (Metal Dielectric Waveguide) which could be a priority for terahertz physics and technology.
-
Sataton Instruments Technology CO., Ltd
Medical face mask differential pressure tester also called mask breathility tester is to determine the breathability of medical face mask materials. The tester can measure the differential pressure (Delta P) required to draw air through a measured surface area at a constant air flow rate is used to measure the air exchange pressure of the medical face mask materials. By providing the suction air through the holding sample, the tester can measure the Delta P by differential pressure transducer. It is to determine the air permeability and using comfort of the materials for medical mask.
-
HIGHVOLT Prüftechnik Dresden GmbH
The TE measurement complements the high voltage test and is part of the routine and type testing of numerous electrical devices. It is one of the most important non-destructive methods for detecting faults in electrical installations. The breakdown of an insulating material usually occurs at an internal weak point, which usually already shows a partial discharge activity in advance. For this reason, measuring partial discharges can help prevent costly damage. The TE measurement is thus used for quality testing and diagnosis in the factory as well as during on-site testing of cables, GIS, power transformers and transducers or rotating machinery and their components
-
779522-01 -
NI
24 V to 60 V, 8 Channel (Sinking/Sourcing Input), 250 µs C Series Digital Module - The NI‑9422 works with industrial logic levels and signals to directly connect to a wide array of industrial switches, transducers, and devices. Each channel accommodates 24 V to 60 V digital input signals. The NI‑9422 features channel‑to‑channel and channel‑to‑earth ground isolation for the highest level of safety for automotive and industrial environments The NI‑9422 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization.
-
779307-01 -
NI
The PCI‑4461 is a high-accuracy data acquisition module specifically designed for sound and vibration applications. It provides simultaneous two-channel dynamic signal generation and simultaneous two-channel dynamic signal acquisition with six gain settings to configure the input range. The PCI‑4461 also includes software-configurable AC/DC coupling and integrated electronic piezoelectric (IEPE) conditioning to ensure precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. Common applications include audio test; automotive test; noise, vibration, and harshness (NVH) analysis; and machine condition monitoring.
-
Unitech Scales And Measurements Pvt. Ltd
Dead Weight Pressure Gauge Tester is ideal for testing and calibration of pressure gauges,pressure transducers,recorders,digital calibrators etc. The system used in the dead weight is vertically mounted precision lapped piston and cylinder assembly with accurately calibrated mass for loading the piston. Pressure is built easily by single cylinder pump at very high rate. The whole system is housed inside a stainless steel case with elegant look. Pressure ports are provided to fix the gauges to be tested. Acrylic see-through oil tank is designed to use it as oil reservoir.
-
HydroSweep DS -
Teledyne Marine RESON B.V.
The HydroSweep DS is a deep water multiebeam echosounder ideally suited for seabed mapping in deep water up to full ocean depth based on a sonar frequency between 14 kHz to 16 kHz. Beside bathymetric depth information from 10 m to more than 11,000 m, sidescan data and backscatter data for seabed classification are acquired. The HydroSweep DS does not only gather sea floor information, but also uses adaptive bottom tracking windows to identify sonar targets in the water column and can be optionally operated as a parametric sub-bottom profiler without additional transducers and electronics.
-
Extech SD900 -
Extech Instruments Corporation
Extech's SD900 allows technicians to easily monitor and record DC mA values from 3 external sensors, transducers, and other sources using one meter. It also stores the time and date of when readings are taken. The logger features a large triple LCD display and records data on an SD card in an Excel®-ready format for easy transfer to a PC for analysis, trending, and archiving. Complete with six AAA batteries, SD memory card, Univeral AC Adaptor with multi-plugs (US, EU, UK, AUS), 3 input connect sockets, and mounting bracket.
-
MMX-6 -
Dakota Ultrasonics
The MMX-6 is a simple to use hand-held Ultrasonic Thickness Gauge with the ability to measure through paint and coatings and eliminate the thickness of the paint or coating. The MMX-6 uses a dual element style transducer. With the single press of a button, the MMX-6 can be switched between pit or flaw mode ( pulse-echo), and through paint/coatings mode (echo-echo) for maximum inspection efficiency. The MMX-6 is equipped with a bundle of features to make your job easier: Alarm mode, high speed scanning, and data send are the main features of the MMX-6. The MMX-6 comes as a complete kit, ready to use, and is backed by Dakota Ultrasonics 5 year limited warranty.
