Filter Results By:
Products
Applications
Manufacturers
-
product
Data Logger
MS6D
Data loggers are designed for measuring, recording, evaluation and subsequent processing of input electrical signals, which are subject to relatively slow changes (> 1s). In conjunction with the appropriate sensors and transducers are suitable for monitoring physical quantities.
-
product
Digital Display for the Transducers and Transmitters
PS57
The PS57 is a combination power supply and 4 1/2 digit LED display for the P55/P855 family of pressure transducers and transmitters. The PS57 accepts 110 VAC power and provides the required 24 Vdc excitation for the transducer. The transducer signal is received and displayed directly in engineering units with bright 0.56 high red LEDs. The user can re-scale the display and set the decimal point by configuring internal jumpers. The analog output of the transducer, 5 Vdc or 4-20 mA, is available on rear-panel terminals.
-
product
AC and DC Current or Voltage Transducers
VT7 AND VT8 Series
The Model VT7 Series dc voltage transducer produces an output which is directly proportional to the input from dc to 10kHz. It functions as a millivolt dc shunt or a high voltage isolator to 1000V
-
product
Digital Variable Impedance Transducer
digiVIT
Kaman Fuzing & Precision Products
The Most Advanced Digital Variable Impedance Transducer for NoncontactLinear Position / Displacement / Proximity Sensing* Self tuning bridge, will perform with nearly any sensor, any conductive target * Pushbutton calibration * Pushbutton temperature compensation * Pushbutton zeroing * Embedded intelligence, all functions accessible without a PC * Large easy to read digital display * Scrolling menus for set up and calibration * Ethernet communication * No sensor, shorted sensor detection
-
product
Phase Angle and Power Factor Transducer of Single-phase AC Electric Power
NMTFi
The NMTFi device is a phase angle and power factor transducer operated in single-phase power network and featuring two independent analogous outputs. The A output measures the phase angle between voltage and current, the B output measures the power factor. In such a was one single NMFTi transducer is able to replace two customary transducers thus making it possible to achieve significant savings in installation space.
-
product
Transducer Calibration
m+p SensCal
Regular transducer calibration is an essential requirement for maintaining the accuracy, reliability and repeatability of the results obtained from a measurement system. m+p international’s m+p SensCal program provides a quick and simple process for calibrating accelerometers (piezo-electric with charge output or IEPE, piezo-resistive, capacitive) in your laboratory, as well as velocity or displacement transducers.
-
product
Combined Pressure and Temperature Transducers
We offer some different styles of combined pressure and temperature transducers which are well suited to Motorsport applications. These include the EPTT5100 combined pressure and temperature transducer, which, has an internal temperature sensor, and the miniature EPTTE1400 combined pressure and temperature transducer which has an external temperature probe.
-
product
Strain Gauge Measuring Instruments
It is a Strain Gage Indicator and also function as a Strain Gage Transducer Indicator.As a Strain Gage Indicator, it can support 10 types of bridges and dummies. While if used as a Strain Gage Transducer Indicator, there are 24 bits A/D converts to make the measurement.
-
product
Charge Amplifier
ZET 440
Charge amplifier ZET 440 for piezoelectric detectors is intended for:*amplification and conversion of output signals of primary piezoelectric transducers with charge output;*amplification and conversion of output signals of primary transducers with the IEPE type in-built electronics to voltage;*gain ratios: 1, 10, 100;*LPF: 0.1, 1, 10 Hz
-
product
Transducers and Probes
Olympus NDT probes and transducers are high-quality inspection equipment available in a range of frequencies, configurations, connection styles, and cable types. All our probes and transducers are lightweight but solidly constructed.
-
product
Signal Conditioners & Measuring Transducers
Signal conditioners and measuring transducers ensure interference-free signal transmission in measurement and control technology. From highly compact 6 mm signal conditioners and measuring transducers through signal conditioners with functional safety to signal isolators for intrinsically safe circuits in the Ex area: our signal conditioners and measuring transducers ensure interference-free signal transmission in MCR technology.
-
product
Custom Industrial Torque Sensors
Datum Electronics are able to provide both modular and custom designed torque and rotary strain measurement solutions, which can be complete as one off or as fully integrated OEM solutions.In many cases, it is better to use an existing shaft or test rig and use custom industrial sensors instead. This process reduces the cost of fitting a conventional torque transducer and it improves the torque measurements, taken by maintaining the dynamics of the driveline.
-
product
High Performance Baratron® Absolute Pressure Transducers
These high performance Baratron® capacitance manometers operate at ambient temperature. They are referenced to vacuum for gas independent, direct measurement of absolute pressure.
-
product
Actuators, Adjusters, & Transducers
We offer a wide range of adjustment screws, micrometers, and kinematic positioners, as well as stepper motor, DC servo, high-precision piezo inertia actuators, and voice coil actuators. Additionally, our piezoelectric offerings include modular, screw, and replaceable-tip piezoelectric actuators, as well as Langevin transducers for ultrasonic welding applications. A wide variety of piezoelectric chips and stacks are also available.
-
product
Power Transducers
FUD-I
Beijing GFUVE Electronics Co.,Ltd.
Single phase current / voltage transducer AC current / voltage transducerAccuracy class can reach 0.2%AC input range can be customized DC output range can be customized
-
product
Signal Conditioners
Metra Mess- und Frequenztechnik in Radebeul e.K.
Metra has been manufacturing amplifiers for piezoelectric transducers for over 50 years. We offer economic charge amplifiers and signal conditioners for IEPE transducers including microphones.
-
product
Sensors
To measure machinery or structural vibration, a transducer is needed to convert the mechanical motion into an equivalent electrical signal. Each sensor has distinct advantages in certain situations and limitations in other, so it is important to select the most suited transducer or sensor for your job. Equally, important is selecting the appropriate parameter of vibration amplitude for measurement. IRD® has a wide range of transducers and accelerometers available to help you obtain accurate, reliable data, whether your concern is vibration monitoring, analysis, or dynamic balancing.
-
product
Power Frequency Transducer
PP1S
1. Measuring and conversion IEC 6882. Dielectrical strength IEC 688 4 KVac / 1 min.3. Impulse test ANSI C37.90 / 1989 IEC 255-3 5KV ( 1.2 x 50 us ) 3KA ( 8 x 20 us ) - current coil4. Surge test (ring wave) ANSI C37.90 / 1989 ( 3KV - 0.5us / 100KHz ) IEC 255-3 ( 2.5KV - 0.25ms / 1MHz )5. Adaptability for power system VDE 0110 6. Measuring reliability VDE 3540
-
product
Seismic Sensors & Transducers
Displacement Pickups are vibration transducers that incorporate a spring-mass system with eddy-current damping using a frictionless pivot. This pivot is a spring flexure that serves as the ‘spring’ and a moment arm attached to the pivot serves as the ‘mass’, which allows resolutions down to the micro inch range. At frequencies above 50Hz, the mass remains fixed in space and becomes an inertial reference. A transducer within the pickup senses the motion of the mounting base relative to the inertial reference and converts it into a proportional signal. Appropriate damping results in a frequency response flat down to 10 Hz. Note that the pickup senses in only one plane, which is perpendicular to the mounting base.
-
product
Rotational Rheometer
ARES-G2
The ARES-G2 is the most advanced rotational rheometer for research and material development. It remains the only commercially available rheometer with a dedicated actuator for deformation control, Torque Rebalance Transducer (TRT), and Force Rebalance Transducer (FRT) for independent shear stress and normal stress measurements. It is recognized by the rheological community as the industry standard to which all other rheometer measurements are compared for accuracy.
-
product
Humidity Transducers & Transmitters
TE Connectivity (TE) offers packaged humidity and temperature sensors with voltage (analog) output signals. Designed for 2% accuracy in ranges from 10-95% relative humidity (RH), these sensors can be used for HVAC and air quality applications in which compensation for humidity is required. A specialized version for low RH settings is available.
-
product
Pressure Sensor Kit for Changing Ranges
DP15TL
The wide range of diaphragms furnished eliminates expensive stocking of several transducers and offers the versatility of the differential type bi-directional transducer at a very low cost. The broad line pressure capability of this unit makes it useful in almost every laboratory application from flow to level measurement, vacuum to 3000 PSIG. The high output, when used with a carrier system such as the Model CD15 Sine Wave Carrier Demodulator or the CD12 Transducer Indicator, provides resolution equal to many secondary standard units.
-
product
Analog Transducers
Scientific Columbus
Scientific Columbus brand Analog Transducers can cover any power application with the wide variety of products. Select from any circuit type, input and power range, frequency, analog output and accuracy range and you will have an exact fit for any application.
-
product
Single-Channel DC Powered Carrier Demodulator
CD16
The CD16 Miniature Carrier Demodulator is designed to deliver a 0 to 5 Vdc output from a variable reluctance transducer and operate from unregulated 9 to 55 Vdc power. A square wave excitation of 5 kHz is furnished to the transducer and the solid state integrated circuit amplifier and demodulator converts the transducer signal to an analog dc output. Zero and Span adjustments are made through access holes in the case.
-
product
Miniature Fiber Optic Pressure Transducers
*The diameter of the working length section can be as small as 0.5 French *The sensor tip size can be as small as 0.8 French The flexibility of the glass fiber offers excellent deliverability without being prone to kinking like electrical wires *The front looking configuration of the sensor tip prevent side-facing/wall bouncing artifacts in the measurement*The lack of metallic components provide full immunity to interference from RF, MW and MRI systems
-
product
6-Component Wheel Force Transducer
Whether vehicle dynamics tests, brake tests or determination of load spectra - the new 6-component Wheel Force Transducer WFT-Cx measures all forces and torques acting on the vehicle with high precision. The robust housing reliably protects against dirt, water and snow and allows applications in any weather.
-
product
Power Cell Power Transducers for Wide Ranging AC/DC Loads
PH-3A and PH-1000
You can know the load on an electric motor by measuring the electric current going to the motor (Amps). But, this is not the best way to do it since a lightly-loaded motor doesn't use the electricity very efficiently. (In technical terms, the power factor is low.)A better way to know the load is to measure the motor power. (Power is measured in Horsepower or Watts.) Motor power gives you a straight line so it works well even when the motor is lightly loaded.The Power Sensors that we make measure the motor load (Horsepower or Watts) and send a signal to meters or computers. The operator can see what the status is on the meter or, the computer can make decisions.
-
product
State, Event & Pulse Data Loggers
These data loggers can record rates from pulse output transducers, on/off or open close state changes or events.
-
product
Miniature Pressure Transducer
EPT1200
The EPT1200 series of Pressure transducers has a miniature design using a hermitically welded, thin filmmeasuring cell, coupled with high level output circuitry. This technology ensures this sensor is suitable for some of industries harshest environments, including automotive, industrial hydraulics, refrigeration, off-road, construction and agricultural applications. The EPT1200 and 1500 series offer measurements in gauge and absolute pressure, with ranges up to 400 Bar and are backed by a one-year warranty.Miniature design | Rugged construction | Wide operating temperature range | Long life High performance
-
product
General Purpose Basic Carrier Demodulator
CD15
The CD15 Sine Wave Carrier Demodulator operates with variable reluctance transducers to provide a DC output signal for dynamics as well as steady state measurements. A 5kHz sine wave excitation is applied to the two inductance ratio arms of the transducer and the resulting output is demodulated and amplified using the latest integrated circuit techniques. The DC output is obtained from an active filter circuit and gives a uniform response from steady state to 1000 Hz. The low impedance sine wave excitation allows operation with the transducer located over 1,000 feet from the CD15.
