Time
is an illusion of duration.
See Also: Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Timing, Counter / Timers, Atomic Clocks, Phase
-
product
Solar Power Meter
SOLAR POWER METER* 3 functions : Solar power, Power integration, Transmission* Select either W/m^2 or Btu / (ft^2xh) power units. Real time SD memory card Datalogger, it Built-in Clock and Calendar, real time data recorder.sampling time set from 1 second to 3600 seconds.Spectral 400 to 1100 nm2000 W/m^2, 634 Btu/( ft^2 x h )
-
product
4-CH 16-Bit 80 MS/s PCI Express Digitizer
PCIe-9834
ADLINK's new PCIe-9834 high-speed PCI Express digitizer, featuring four simultaneously sampled 80 MS/s input channels with 16-bit resolution, 40 MHz bandwidth, and up to 1 GB DDR3 onboard memory. Each of the four input channels supports up to 80MS/s sampling, with 16-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no interchannel phase delay. The extremely large onboard memory enables long recording times even at the highest sampling rates. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9834, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card.
-
product
Data-based Modeling and Calibration
ASCMO
ETAS ASCMO is the easy-to-use-solution for advanced model-based calibration and data-based modeling in significantly less time. ETAS ASCMO enables the fast and efficient development of accurate data-based models. Once created, these high-accuracy models can be used to optimize parameters of real systems such as engine ECUs or plant models in different simulation environments (e.g. Simulink or HiL-Systems). Both, steady state and dynamic/transient system behaviors can be captured.
-
product
Advanced In-Kiln Moisture Measurement System
MC4000
The MC4000 Advanced In-Kiln Moisture Measurement System enables the kiln operator to monitor the moisture content of each charge and develop consistent drying time schedules for improved kiln performance and reduced operating costs. The MC4000 will cut costs due to degrade and overdrying and improve grade recovery to help increase the bottom line.
-
product
mmWave Transceiver System
The mmWave Transceiver System is a modular hardware solution for prototyping real-time communications systems for mmWave frequencies. With 2 GHz of bandwidth, the system can be used to evaluate the ultrawide bandwidth signals being proposed for next-generation wireless communications standards in real time. You can analyze these ultrawide bandwidth signals in real time using a multi-FPGA architecture for computationally intensive digital signal processing. With this processing capability, you can build a real-time two-way communications link with up to 2 GHz of bandwidth.
-
product
CAN Interface Board
- Auto Learning for slow detection and easy commissioning.- Encoder signal for floor detection.- Detail diagnostic of individual components ensures safety and reliable operation- Attached ARD for each panel for rescue in case of power fail.- Intelligent algorithm to attend any calls within 10 seconds for standard configuration.- VIP option, Fireman switch, overload protection $ protection of all other standard interfaces integrated.- Announciator is integrated with Gong bell.- Preferable selection of floor by user, software functional options, Delay times and important configurations.- Error diagnosis by PC interfaces, eleavator error history and services details make your maintenance job very effective and efficient in time period
-
product
High Dynamic Range IR Camera
HDR-IR
These cameras maximize camera sensitivity automatically for any static or dynamic scenes. They find the best exposure time according to the scene and allow to resolve targets up to 2500C.
-
product
Vibration Analysis Software
VibroDesigner
VibroDesigner software is used for data acquisition, storing and analyzing. Using this software with portable STD-500/510/3300 or stationary CTD3168/2160/2060 units helps to schedule machinery maintenance at a convenient time.
-
product
Diffusion Sensors
BASIC EVO
Diffusion sensors for room air monitoring are available from smartGAS as the BASIC EVO series. Like all smartGAS sensors, they are characterized by low detection limits, low drift, a wide temperature range as well as a fast response time and low maintenance. The BASIC EVO series is the optimal solution for all applications in which a room air sensor should be reliable and easy to handle at the same time.
-
product
Class 2 Sound Level Meter
SP79
The SP79 is a Class 2 sound level meter for on-site measurements in accordance with Noise at Work legislation in industrial and office environments. Featuring A and C frequency weighting and fast and slow time weighting, the compact design can be handheld, or mounted on a tripod for longer term monitoring of Min / Max values. Detailed recording and analysis can be made using the AC and DC outputs. The SP79 complies with BS EN 61672-1:2003 and is supplied with a detachable windshield and hard carry case. The large high contrast display includes both digital reading and analogue bar graph. An optional Class 2 sound level calibrator is available to verify accuracy before and after readings in accordance with international standards. The SPC70 is simple to use and provides a 1kHz reference at 94dB and 114dB.
-
product
Dual Channel Digital Receiver
MS 1740
Dual Channel Digital Receiver is a complete high−frequency dual−channel A/D converter capable of sampling rates up to 210 MHz. It accepts two front panel analog inputs and delivers digital output samples over four FPDP (Front Panel Data Port) connectors utilizing FPDP standards. The Dual Channel Digital Receiver features two 12−bit Analog Devices AD9430 A/D Converters, and two user−configurable Xilinx® Virtex−IV Series FPGAs. It also features a VME A64/D64 slave interface for setting up operating modes and selectable A/D range, and optionally provides 32−bit access from the VMEbus to the FPGAs. It is an ideal system as a high−speed data acquisition front end for real time recording and digital signal processing systems.
-
product
Multi-Sensor Systems
Multi- sensor surveillance systems represent a fast growing group of electro-optical systems of critical importance in both defense and civilian applications. At the same time they are the most expensive groups of electro-optical systems. Most advanced but rarely met multi-sensor surveillance systems are built from a long series of sensors like thermal imager (or two thermal imagers, color VIS camera, low light VIS-NIR camera, SWIR camera, laser range finder, laser designator, laser pointer, illuminator located on a stabilized platform and such systems. Simpler systems built from two-three sensors located on smaller stabilized or non-stabilized platforms are more common.
-
product
Companion Tool to VS for Test Time & Pin reduction
UltraScan
UltraScan is SynTest's solution to combat increase in test time. In 130 nm or smaller ? nanometer geometries, many defects become delay defects and it becomes necessary to use delay tests to detect the transition faults and path delay faults. Often bridging tests are also required.
-
product
Standard High Speed D/A Converters
Analog Devices digital-to-analog converter (DAC) portfolio provides solutions for your high speed and precision DAC applications. Thanks to complete data sheets and evaluation boards, as well as broad support among our clock and timing, RF, power management, and op amp portfolios, our DACs can help you reduce time to market and system design costs. A high speed range from 30 MSPS to multi-GSPS, 8- to 16-bit resolution, and a tiny package are just some of the features that make our industry-leading d/a converters stand out.
-
product
Schildknecht Flexing Tester
TF117A
TESTEX Testing Equipment Systems Ltd.
Schildknecht Flexing Tester is designed to determine the resistance of coated fabrics to damage by Flexing due to oscillation at 500 times per minute. Accommodates 10 specimens, safety shield is offered to protect operator. Test speed, the counting, the timing is set and displayed on the LCD and controller.
-
product
HEV & EV Power Tester
EVd-40
The EVd-40 Power Tester is a pre- and post-reconditioning tool for quality control of aftermarket HEV & EV battery production. The equipment integrates a “smart” charger (Sorensen XG 1700 or Kepco KLN 1500W) with NuVant Systems high power discharge electronics. The "power test" discharges battery packs at high power (10,000 watts), while tracking module voltages. The software monitors up to 40 module voltages at a time, identifying any weak modules. The "smart" charger performs charging constant current (CC), constant voltage (CV) and complex mixed mode constant current – constant voltage (CCCV) charging protocols at voltages up to 600 V. This enables recharge of any type of rechargeable battery.
-
product
Electric Submeters
Measurlogic carries an extensive line of AC and DC electric submeters that are easy to implement. Whether starting out with submetering for the first time, or just looking to upgrade your system, our goal is to make your life easier. We carry an array of mounting options for a sophisticated, seamless integration with your property.
-
product
High Power DC Electronic Load（1250V）
34300E Series（5KW~40KW）
34300E Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
product
PXI/PXIe Solid State Attenuator, Triple, 6GHz, 50Ω, SMA
41-182B-003
The 41-182B-003 (PXI) and 43-182B-003 (PXIe) are programmable RF attenuator modules with 3 channels in one slot capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuators use solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
product
*Structural Analysis
Guangzhou Amittari Instruments Co.Ltd
With proven accuracy every time, Altair offers industry-leading engineering analysis and optimization tools from simulation-driven design concepts to detailed virtual product validation and simplified modeling workflows to advanced high-fidelity model building. Whether big or small, our customers trust their decision making to Altair, the pioneer of simulation-driven design.
-
product
MPO IL/RL Testers
Wuhan Sunma Technology Co., Ltd.
SunmaFiber also supply MPO Tester from Yokogawa, Agilent(Keysight), Optical Talk Set, fiber splitter PDL Loss tester, MTP Tester, fiber Return Loss & Insert Loss tester and other MTP/MPO testing solutions, you can find the most effective products in a reasonable price. Welcome to SunmaFiber. Contact us at Sales@SunmaFiber.com or Live Chat with us. Buy other fiber optic products on SunmaFiber. Save your money & time right now!
-
product
Test Services
D-Coax offers RF/Microwave test services for your researchprojects, as well as, production quantities tests. We have available resources and expertise in the high frequency interconnects testing that will benefit your research and products. We will work with you to make your requested tests the most accurate and reliable and we'll complete them in a timely fashion. The following parameters can be characterized or tested to specifications with our test services: Time Domain: Impedance, Impedance profile, rise time, propagation delay, skew and more. Frequency Domain: S21 - Insertion loss, S11- Return loss, S12 - Reverse Insertion loss (port 2 insertion loss), S22 - Reverse Return loss (port 2 return loss) and more.
-
product
RF Ports Alignment Software
With the R&S®RF Ports Alignment software together with the option R&S®SMW-K545, Rohde & Schwarz provides a standard and tailored solution for calibrating amplitude, time and phase of multi-channel SMW setups. The RF Port Alignment automatically collects the gathered correction data for the multi-channel setup using a connected vector network analyzer such as the R&S®ZNA or R&S®ZNB. Thanks to an intuitive graphical user interface the test engineer is guided through the calibration procedure step-by-step in a convenient way. With a calibrated multi-channel setup, tests of advanced systems in wireless communication or of radar receivers can be performed straightforward.
-
product
Broadcast TV Multiviewer Monitoring System
IMS120
The Mividi IMS120 is a broadcast transport stream monitoring system for viewing video and audio services, analyzing transport streams, logging errors, generating alarms, and recording stream. The IMS120 was developed to automate monitoring and error diagnosis at digital head-ends for broadcasters, MSOs, Telcos and online streaming video providers. It is a single Windows based system that can complete tasks previously done by several different pieces of equipment. It will pay for itself in manpower savings over a short period of time.
-
product
System
SYS-36
Systems with 36" chambers tend to be a customer favorite for their flexibility. They are easily used for many different types of coatings. Often times they are best utilized in a prototype or multi part production facility where a specialized system such as a dual chamber box coater is not required. They are, however, still configurable for specialized processes.
-
product
Digital Leeb Hardness Tester
TIME®5350
Beijing TIME High Technology Ltd.
TIME Group manufactured the first Leeb hardness tester in China in 1989 and has been the leading manufacturer of hardness testing equipment since then. Among all the TIME hardness testers, TIME®5350 is the best one with all the features. It looks like a mobile phone, easy to carry and makes a perfect tool for on-site hardness testing. Maximum 32GB MicroSD card can be used to store measured values.
-
product
RTOS Scheduling Visualization
RapiTask
*Examine Ada, C or C++ applications via scheduling visualization*Locate rare timing events that need attention*Identify bottlenecks in your application by analyzing capacity issues*Compare scheduling algorithms from different RTOSs
-
product
400 MHz to 4.4 GHz, Reconfigurable USRP Software Defined Radio Device
783147-01
400 MHz to 4.4 GHz, Reconfigurable USRP Software Defined Radio Device - The USRP-2942 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and significantly shorten time to results. You can prototype a wide range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.
-
product
Wireless Hazard Monitoring
When it comes to hazard monitoring, we know it simply has to work. HazardPRO was designed from the ground up to provide turnkey, reliable, and consistent protection for your most valuable assets—products, facilities, and most importantly, people. Consistent operation is ensured with built-in tools such as self-diagnostics, transmission logging, and redundant radios providing you confidence that your critical processes are being monitored and logged at all times. Wireless nodes utilize temperature (bearing, ambient, and stud), RPM shaft speed, alignment, and vibration sensors. Ambient Sensors ensure bearing and alignment measurements are relative to the surrounding environment.
-
product
Fiber Inspection Probe
FIP-920
FIP-920 Fiber Optic Inspection Probe combines a 3.5” high definition TFT LCD display, provides a detailed image of fiber end-face, zoom in/out feature make it easy to identify the smallest particles, scratches. With the attached SD card memory, you can capture/record the live end-face image, the image file can be reviewed/transferred via SD card reader or USB cable. Up to 8hrs battery working make it possible to inspect the fiber end-face at any time and any place.
