Showing results: 1111 - 1125 of 2240 items found.
-
PCI-7256 -
ADLINK Technology Inc.
*Supports a 32-bit 3.3 V or 5 V PCI bus*16-CH latching SPDT relay outputs*Power saving on relay actuation*Output status unchanged when power-off*On-board LED indicators for relay status
-
PCI-COM-1S -
Acces I/O Products, Inc.
The PCI-COM-1S is a single port asynchronous serial communications card that can be installed in any 3.3V or 5V PCI slot computer. The card meets the MD1 PCI Low Profile Specification and is just 4.7 inches long. For low profile systems please use P/N LPCI-COM-1S for the card to be shipped with a low profile bracket.
-
TE5100-PCI -
TEAM SOLUTIONS, INC.
The TE5100 is a 100MHz Direct Digital Synthesized Signal Generator available in a 3U, CompactPCI or straight PCI format. The TE5100 generates Sine and ACMOS/TTL output signals simultaneously up to 100MHz in 1 µHz steps. Sweep, FSK, Chirp and Single Tone are generated on board. The virtual panel allows control up to 100MHz of all parameters. The TE5100 is equipped with a ±1ppm on-board TCXO clock and can accept an external clock source.
-
PCI-COM232 -
TEAM SOLUTIONS, INC.
Serial ports: 1Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with cable to DB-9 (DB-25 optional)Power: +5V only
-
PCI-6308 Series -
ADLINK Technology Inc.
*Supports a 32-bit 5 V PCI bus*Isolated 8-CH 12-bit voltage output*2500 VRMS optical isolation*Jumper selectable bipolar and unipolar output ranges*4-CH isolated DI and 4-CH isolated DO*Current output version available on PCI-6308A
-
PCI-P104-ADAP -
Acces I/O Products, Inc.
Model PCI-P104-ADAP simply allows for the installation of a PC/104-Plus or PCI-104 board into any Universal PCI, 3.3V or 5V slot. It is a standard PCI bus card that supports 32-bit wide data transfers to and from a PC/104-Plus board. This allows any user the convenience of hardware testing, software development, and debugging of a PC/104-Plus board in a PC environment.
-
PCI-ICM-1S -
Acces I/O Products, Inc.
The PCI-ICM-1S is a single port asynchronous optically isolated serial communication card that can be installed in any 3.3V or 5V PCI slot computer. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
PCI-1553 PLX -
ALPHI Technology Corporation
The PCI-1553-X uses a single UTMC’s Sµmmit or BCRTM communication device as its 1553 bus controller, or remote terminal, or monitor terminal. The single controller has two redundant channels. This controller accesses 64Kx16 word of external memory and has external for both channel A and B. The 3U PCI board has on-board transformersfor both channels.
-
PCI-COM2S And PCI-422/485-2 -
Acces I/O Products, Inc.
The PCI-COM2S and PCI-422/485-2 are dual-port, asynchronous serial communications cards designed for use in PCI-Bus computers. They are 6.5 inches (165 mm) long and may be installed in any 5V PCI slot in IBM and compatible computers. Each independent port supports RS-422 and RS-485 balanced-mode transmission/reception, and on the PCI-COM2S, RS-232 single-ended transmission/reception as well.
-
PCI-DIO-120 -
Acces I/O Products, Inc.
The PCI-DIO-120, PCI-DIO-96 and PCI-DIO-72 are parallel digital input/output cards designed for use in PCI-Bus computers. The same printed circuit board is used for all three models and is populated for 120 bits, 96 bits and 72 bits respectively. The card is 12.2 inches (310 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
PCI-4pack -
ALPHI Technology Corporation
The PCI-4pack module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the PCI-4pack is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc.Custom application software can be downloaded to the DSP via the PCI bus. Windows 95 and WinNT drivers are standard.
-
PCI-COM232/4 -
TEAM SOLUTIONS, INC.
Serial ports: 4Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with fanout cable to 4 DB-9 or DB-25 male connectorsPower: +5V only
-
PCIe, PCI, PC/104, CAN -
BMC Messsysteme GmbH
PC data acquisition cards are particularly suitable for stationary measurement applications. Outstanding in this category are the PCI(e) multi-function cards PCI-BASEII and PCIe-BASE on which you can plug different measurement and control modules to optimize the price-performance ratio.
-
PCI-8134A -
ADLINK Technology Inc.
The PCI-8134A is a 4-axis entry-level motion controller. A PCI interface provides plug-and-play capability for easy maintenance, and supports up to 12 cards in one system, to control 48 motors. The PCI-8134A provides pulse train command output up to 2.4MHz and encoder input up to 2.4MHz in 4xAB phase mode. Programmable acceleration and deceleration allows flexible programming of in-house applications, and dedicated motion I/Os shorten system installation. The PCI-8134A also supports 2~4 axis linear interpolation for simplified synchronous motion. The PCI-8134A is a cost-effective motion controller enabling implementation and control of most of point-to-point, conveyer, and load-and-unloader applications.
-
PCI-1553DDC-2 -
ALPHI Technology Corporation
The PCI-1553-DDC-1/2 implements a complete single channel dual-redundant MIL-STD-1553 bus terminal on a half size PCI Card. Full BC/MT/RT modes are supported. 0°C to 70°C operating temperature is standard. Included is an DDC Enhanced ACE intelligent communications protocol engine, dual transceivers and encoder / decoders, shared memory, and management logic.