Showing results: 76 - 90 of 266 items found.
-
MS 1721 -
Meltronics Systemtech
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- Spartan-3AN FPGA with ARINC 717 IP Core- One Channel ARINC 717 Transmitter and Receiver- Generates all PCM telemetry signals like NRZ, Bi-Phase, - Differential Bi-phase, DM signals- Used to test all types of PCM based telemetry equipments- Configurable output signals format (parity, word length, Minor, Major frame, Bit position)- User can configure the words and word positions in the frame- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
Model 7190 -
Pentek, Inc.
- Simultaneous synthesis of up to 5 different clocks- 8 SMC clock outputs- Ideal for A/D and D/A converter clock sources- Typical phase noise: -125 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 or 10 MHz- Four quad VCXOs allow selection from 16 different base frequencies- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 500 MHz- Control and status via PCI bus interface
-
PMC650 -
Silicon Control Inc.
The PMC650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
-
PMC-1553 -
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
TPCI270 -
TEWS Technologies GmbH
The TPCI270 is a standard 33 MHz, 32 bit PCI carrier for a single PMC Card. Itprovides PMC front I/O and PMC P14 rear I/O. This PMC to PCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in standard PCI systems.
-
TCP262 -
TEWS Technologies GmbH
The TCP262 supports standard PMC front I/O and CompactPCI rear I/O fully compatible to the TCP260. The PMC slot 2 (upper PMC) I/O lines are connected directly to the CompactPCI connector J5. The PMC slot 1 (lower PMC) I/O lines are connected directly to the CompactPCI connector J3.
-
cPCIBPMC3U32 -
Dynamic Engineering
cPCIBPMC3U32 is a 3U 4HP PMC adapter for cPCI. One PMC position is provided with a 32 bit interface for both the PMC and the cPCI backplane. User programmable VIO on the PMC side of the bridge. High capacity mini-planes with filtering for 3.3 and 5V.
-
-
-
Cambridge Pixel Ltd.
The HPx-250 card provides a similar set of capabilities to the HPx-200 but on the compact PMC form-factor. The PMC board may be fitted to a compact PCI (cPCI), VME or VPX host processor card for a rugged embedded solution.
-
TPCE261 -
TEWS Technologies GmbH
The TPCE261 is a standard height PCI Express Revision 2.0 compatible module that provides one slot for a single-width PMC module used to build modular, flexible and cost effective I/O solutions for all kinds of applications like process control, medical systems, telecommunication and traffic control. The TPCE261 is a versatile solution to upgrade well known PMC I/O solutions to the PCI Express signaling standard.
-
8091 -
ELMA Electronic, Inc.
The PMC-to-PCI Adapter for Test is an active extender that accommodates live insertion of one PCI Mezzanine Card (PMC) for performance analysis and testing in a PCI bus environment.
-
cPCIBPMC3U64ET -
Dynamic Engineering
By customer request Dynamic Engineering has developed two extended temperature versions of the popular cPCIBPMC design. The design effort included switching to a new bridge to meet the temperature and timing requirements. The new bridge brings new features including the ability to operate the PMC side at a higher clock rate than the cPCI side. The new bridge also has built in features for local address spaces, using the PMC clock in monarch mode for the secondary side, and operating in transparent or non-transparent modes
-
PMC-429 -
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx ChannelsProgrammable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application Interface supporting C++, C#, and .net DevelopmentDevice Driver Support: Windows, Linux, VxWorks, and other operating system - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software