Filter Results By:
Products
Applications
Manufacturers
Test Heads
1) interchangeable assembly connecting test signals between DUT and ATE. 2) representation of a human head. 3) provide network test access.
See Also: Heads, Test Probes
-
product
Battery Management (BMS) Environmental Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
product
Functional Test
cUTS
Get the essentials of measurement automation to power tests of simpler PCBAs and subassemblies. compactUTS (cUTS) is a cost-effective platform for automating manual tests of devices with fewer than fifty cable-accessible test points in manufacturing environments with moderate production volume. DUT-specific electrically keyed cables make changeover quick and easy.
-
product
Functional Test
UTS
The UTS functional test system is perfect for electronics manufacturing operations that have a mix of products where operators load and unload devices under test (DUT) and routinely change out fixtures for each type of DUT.
-
product
Benchtop Automated Functional Test
midUTS
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
product
PXI Digital Test Instrument
PXIe-6943
Conduct pattern-based digital tests incorporating the latest parallel, digital, serial, and bus protocols with the PXIe-6943 digital test instrument.This instrument is TPS-compatible with the legacy VXI digital test instrument from Astronics as well as other instrument vendors.
-
product
PXI Integration Platform
ATS-3100
The new ATS-3100 enables you to rise above the module level and shift your focus to the sophisticated test solution you’re actually building. Simply add your instruments, software, and customization to create a complete solution. Or, if you're short on time or resources, ask Astronics Test Systems to do the finishing work for you.
-
product
2-Module ICT System, I317x Series 6
E9902G
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
product
Combustion Leak Tester
AC560000
Fast, economical and accurate method to test for combustion gas leaks in head gaskets, cylinder heads and engine blocks. Dual chamber design provides more accurate test results. Test fluid can be used for both gasoline and diesel engines.
-
product
Hydrostatic Head Tester
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester is used for measures the resistance of a fabric to the penetration of water under hydrostatic pressure. Hydrostatic Head Tester complies with AATCC 127, EN 20811, ISO 1420A, etc. Please contact us for Hydrostatic head test procedure.
-
product
Taber® Rotary Abrasers
5135 & 5155
The Taber® Rotary Abraser is an industry standard used in wear and durability testing and is available with either a single test head or dual testing heads, which allows the user to test two different or identical materials simultaneously.
-
product
Shore Hardness Tester
SKZ128
The Shore hardness tester is applied to test the hardness of vulcanized rubber and plastic. The hardness head is installed on the stand. You can also take the head from the stand to carry spot testing.
-
product
Manual Flying Probe Test Systems
They provide flexible measurement technologies like Kelvin and high voltage tests in combination with low tooling costs. atg Luther & Maelzer offers a wide range of different systems starting from standard systems with 8 heads up to oversized systems with 24 test heads.
-
product
RF/Wireless Test Fixtures
Test‐Head Engineering develops and manufactures RF Test Fixtures which allow the testing of RF and Wireless modules and components.
-
product
Signal Integrity Test Products
S1
*Fixtureless Test Solution*Automated Optical Inspection*DC Electrical test*Tests any backplane – Small, large, simple, complex*Now available with 4 heads
-
product
Manual Test Adapter
linear pin compressionhinged carrier for probe cardfacilitated probe tower positioningmounted onto test head stiffener
-
product
Portable Analyzers
The key to the operation of Alpha Moisture Systems' Portable Analysers is the unique Desiccant Dry-Down Chamber. By keeping the sensor dry between tests, the special assembly of the head ensures that the instrument is always ready for immediate use. The head assembly consists of two chambers which have a telescopic action. When the head assembly is in the 'closed' or 'Dry-Down' position, the sensor is completely surrounded by desiccant, which absorbs the remaining water moisture from the sensor and hence it is dry and ready for use. The small space at the bottom of the test chamber enables the sample pipe to be purged before the test commences without wetting the sensor. By placing a finger over the outlet of the head, the sample pressure is able to open the test chamber automatically, exposing the sensor to the gas being tested and enabling accurate reading of moisture content in the sample gas. After each test the head assembly is closed by depressing the inner section so that the sensor will again be dried by the desiccant, leaving the sensor ready for use time and time again. The desiccant is kept in the inner chamber and is not exposed to ambient room air or the sample gas, therefore there is no need for frequent regeneration or replacement of the desiccant.
-
product
Universal Wear Tester
TF213
TESTEX Testing Equipment Systems Ltd.
Universal Wear Tester, to determine the wear and abrasion resistance of fabric used in clothing, footwear and industrials. Universal wear tester Supplies with surface abrasion head (inflated diaphragm method) and Flex abrasion head as well as necessary weights and initial supply of abrasives. Accessories are available for conducting frosting, pilling and edge abrasion tests.
-
product
High-Frequency Head & Torso Acoustic Simulator
HATS
Brüel & Kjær Sound & Vibration A/S
Designed for realistic in situ electroacoustics tests on, for example, smartphones, headsets, audio conference devices, microphones, headphones, hearing aids and hearing protectors. High-frequency Head and Torso Simulator (HATS) Types 5128-C and -D are manikins with built-in realistic ear and mouth simulators that provide a realistic reproduction of the acoustic properties of an average adult human head and torso. High-frequency HATS is designed for in situ electroacoustics tests and can cover the full audible frequency range (up to 20 kHz).
-
product
Magnetic Particle Liquid Checker
S-2A / S-2B
Magnetic particle liquid checker S-2 series is a test bar which can directly check the quality of magnetic particle liquid immediately. Magnetic particle liquid checker S-2A type has a sensor at the head of straight test bar.
-
product
In‐Circuit Test Fixtures
Test Head Engineering designs and builds high‐quality In‐Circuit Test (ICT) Fixtures for HP / Agilent / KeySight Technologies 3070 board testers. We partner with In Circuit Test Engineering, Inc. to provide turn-key 3070 ICT solutions - both fixture and programming.
-
product
HEAD acoustics Radio Analyzer Tool
TUNE
The HEAD acoustics Radio Analyzer Tool TUNE allows a reproducible analytical evaluation of the impact of analog radio broadcast disturbances on perceived audio quality based on auditory test results.
-
product
Pod/Nest Fixtures
Nest and Pod Fixtures are used to test components and sub-assemblies. They typically are built in an array and the devices under test are subjected to tests that simulate operating conditions or life-cycle testing. Test Head Engineering is experienced in providing nest and pod testers that meet the connectivity, ergonomic and mechanical requirements of component testing.
-
product
Head Expanders
By increasing the mounting area of the shaker, multiple items can be tested at the same time, decreasing total test cycle time. In addition, with Guided Head Expanders, payloads with large foot prints can be safely mounted and tested on the shaker, minimizing the risk of damage to the shaker suspension system. Although many head expanders are resonant below 1000 Hz, average or extremal control allows operation to 2000 Hz.
-
product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
product
Functional Test Fixtures
Test Head Engineering's Custom Functional Test Fixtures range from simple to extremely complex. Typically, our customers do their own wiring and programming, but we will complete the job right up to the customer's requirements, including offering turn-key control and test programming through our partners.
-
product
Hydrostatic Head Tester
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester, used for determining the resistance of fabrics (canvas, coated fabrics, cover cloth, rainproof clothing fabrics and geotextile materials) and films to water penetration under pressure while firmly clamped in the test rig of standard area, by means of dynamic test method and static test method.
-
product
Emulation & Test Interface
Solder down modules to suit any package type provides a cost effective solution for replacement test heads, male or female. The mating top modules can incorporate either a ZIF or standard IC socket and the addition of optional test pins if required from RS Components.
-
product
Optical Power Meter with Optical Head
GM8012 + 2 X GM8300X
The UC8820 + 2 X UC8820X optical power meter with optical head offer superior performance for the test of DWDM components, AWG & PLC components, optical amplifiers, and other general purpose of fiber optical test and measurement applications. It is special design for volume production line application.
-
product
VACUUM PRESSURE GAUGE KIT
VG100K
*Accurately tests vacuum and low pressure fuel systems*Heavy-duty 3-1/2" dual purpose gauge reads vacuum and pressure*Quickly diagnose internal engine problems such as bad rings, valves or leaky head gaskets
-
product
HD Tester with VGA, Audio, Video, HD-TVI
M-HD-360A
Fuzhou Metricu Technology Co Ltd
Analog camera testHD-TVI camera test, HD-CVI camera test, AHD camera testDC12V 1A power outputVGA input, support 1920 x 1200P 60FPSAuto HD, auto recognize HD coax camera type and resolutionUTP cable test, detect the near-end, mid-end and far-end fault point of the network cable crystal head