Showing results: 466 - 480 of 701 items found.
-
Leak Testing -
TQC Ltd
TQC have supplied automatic leak test / pressure test equipment for over 25 years. The supply has included simple manually connected leak test fixtures to fully automatic, high speed production leak test facility. TQC supply leak testing equipment to meet the customers requirements.
-
Photo Emission Tech., Inc.
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
Instron
The Instron® Curved Needle Testing System is built on the 5900 system platform and is ideally suited for needles used in abdominal, fistula, vascular, intestinal, or other surgical procedures. This system provides two different needle testing solutions: one for curved needle puncture testing and one for bend testing. The curved needle puncture testing fixture is used to evaluate needle sharpness and insertion force, while the needle bend testing fixture is used to evaluate flexural properties of the needle during use. With its tabletop design, the Curved Needle Testing System has a small footprint and takes up minimal bench-top space. The testing system operates with Instron Bluehill® Universal software that provides test control, data acquisition, test results, and reports, as well as a large library of calculations.
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicators within this range are encased so that the operator can either use it on the move (if battery powered) or be a permanent fixture, e.g.: wall mounted.
-
Radiometrics Midwest Corporation
One of the more difficult tests to understand is shielding effectiveness or transfer impedance. The data from these tests may vary dramatically based on the test method selected, test fixture, test setup, measurement sensitivity, test personnel, etc. At Radiometrics all shielding effectiveness test are performed or supervised by NARTE Certified engineers.
-
Datest
Customer-supplied or developed in-house• Ruggedization of existing (lab-built) fixtures• Co-develop hardware/software• Deployment, implementation, and training• Engineering evaluation tools• Design verification• Medical device evaluation• Manufacturing test systems• Verification test systems• Go/No-go tests• Serialization, recordkeeping, and datalogging• Troubleshooting failed units with other test platforms
-
TA-55 -
Tech-Aid Products
Radar altimeter panel designed after the ALT-50A test fixture. (Ref. Fig. 5-1). Panel allows testing of the indicator or R/T independently or together. An internal power supply is provided to support stand alone testing of the indicator. This panel contains a 4 digit DVM and comes with enclosure. This panel will allow by the book testing.
-
Acculogic Sprint 4510 -
Terotest Systems Ltd.
The Sprint 4510 family of flying probers are well known for their speed, reliability, ease of use and large world-wide installed base.Flying probe testers have few restrictions on access, require no test fixtures, and can test boards with virtually unlimited number of nets, allowing test developers to turn a program around in a short time.
-
GR Series -
Test-X Fixture Products
The 3210 Series Receiver is designed for interfacing the GR 2270 style test fixture. Using patented CAM/TRAC design, the 3210 Receiver provides an accurate, positive locking system that ensures consistent contact throughout the entire interface. With a 5/8" stroke, the 3212 Receiver allows additional clearance for coax and custom block applications.
-
Optomistic Products
The Universal LightSources use a standard 5-volt DC power supply connected via a connecting cable with mating coaxial power plug and terminated with clearly polarized push-on connectors to access fixture 5-volt D.C. supply wire-wrap pins wherever available. Alternatively, the Universal LightSource can be connected to a serial-digital pulse-code-modulated signal source.
-
ORION™ HGO-4000 -
Research Electronics Intl.
The ORION HGO-4000 is REI’s original high gain Non-Linear Junction Detector for special applications. The ORION HGO-4000 can locate listening devices and semiconductors in walls floors, ceilings, fixtures, furniture or containers and provides a user the capability to detect hidden electronic devices, regardless of whether the device is radiating, hard wired, or even turned off.
-
Verisurf Build -
Verisurf Software, Inc.
Verisurf BUILD is the industry-leading tool for real-time model-based inspection, tool fabrication, and computer-aided assembly.Inspect position and profile, set details and fabricate tools, jigs, and fixtures faster and at lower cost than any other process or software.Evolved and perfected from a large installed base at today’s modern aerospace, automotive, and industrial tooling manufacturers.
-
Jackmark Engineering Ltd.
The Automotive assembly track lineside environment requires numerous amounts of tooling & equipment to ensure build phases are completed productively. Jackmark Engineering provides a wide variety of custom designed trackside jigs & fixtures, test leads and assembly aids including validation tooling to various assembly departments from HVAC to end of line.
-
nm-Wave AARTS System -
Accel-RF Corporation
AARTS fully integrated, automated, turnkey system provides flexibility and accuracy in determining RF and DC performance degradation with aging to predict life expectancy for compound semiconductor devices. Our millimeter-wave Automated Accelerated Reliability Test Systems (AARTS) and fixture solutions are available in standard frequency ranges from 26.5 to 67 GHz.
-
410104322 -
Virginia Panel Corporation
The G12 ITA can be used with all G12 Receivers. The ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC Enclosure or customize your own fixture to be attached to the ITA. These are front mounted for ease of installation. A wide range of ITA modules are available separately for user configuration.