Showing results: 181 - 195 of 414 items found.
-
T3DSO2502A -
Teledyne LeCroy
Optional Serial Bus Trigger and Decode options – I2C, SPI, UART, RS232, CAN, LIN which enables users to debug serial buses directly to their Oscilloscope on the T3DSO2000 series. While on the T3DSO2000A series I2C, SPI, UART, CAN, LIN Serial Bus Trigger and Decode options come as standard with optional CAN FD, FlexRay, I2S and MIL-STD-1553B also available on the T3DSO2000A series.
-
T3DSO2204A -
Teledyne LeCroy
Optional Serial Bus Trigger and Decode options – I2C, SPI, UART, RS232, CAN, LIN which enables users to debug serial buses directly to their Oscilloscope on the T3DSO2000 series. While on the T3DSO2000A series I2C, SPI, UART, CAN, LIN Serial Bus Trigger and Decode options come as standard with optional CAN FD, FlexRay, I2S and MIL-STD-1553B also available on the T3DSO2000A series.
-
mPCIe-UCAN2 & mPCIe-UCAN2-ISO -
Acces I/O Products, Inc.
The mPCIe-UCAN2 card features two CAN ports that instantly install in most any operating system as standard COM/ttyS devices. Each port supports CAN2.0 A/B and FD operations including data rates up to 10Mbps and timestamps with 1μs (or 1ms) resolution. These CAN ports can be controlled using a simple ASCII command/response interface using a superset of the popular CAN232 standard (extendedto support CAN FD requirements)
-
YAV90CIN -
6TL Engineering
12 Independent SPST relays Switching up to 8A 250Vac 12 current measurement channels 8x Sense connections General inhibit input CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Thermotron Industries
Each 5-channel CAN and 5-channel LIN can be independently controlled for simultaneous operation. It is an intelligent instrument which uses its own on-board processor to send/receive/compare Controller Area Network (CAN) and Local Interconnect Network (LIN) messages.
-
AIM GmbH
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
CSM Products, Inc.
With up to 12 CAN bus interfaces, freely configurable digital inputs and outputs, Wake-on-CAN, LAN, WLAN - When developing the UniCAN 3 data logger, numerous requirements from state-of-the-art vehicle development were taken into account.
-
YAV90069 -
6TL Engineering
Software configurable for: 1(64×2), 2(32×2), 1(16×2) + 3(16×2). Switching 2A 250Vac. Max switching up to 62.5V CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Module Analyser -
Influx Technology LTD
Module Analyser is a 5 in 1 easy to use CAN bus analyser with the following advantages:■ CAN and LIN monitoring via DBC/LDF/Fibex files ■ Automotive OBD ISO15765 Scan tool and UDS ISO14229■ J1939■ Integrated ODX/MDX editor■ Data acquisition and logging
-
YAV90HVT -
6TL Engineering
32 relays High Voltage (Up to 1500V) Multimeter/Amperimeter 14 bits resolution. 1x Analog Output and 2x Digital Outputs Internal automatic calibration CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available Automatic module identifier
-
Advantech Co. Ltd.
Advantech serial communication cards include RS232, CAN bus, and COM cards.
-
Alto Inspection Corp.
THANKS TO OUR ADVANCED DATA ANALYSIS FUNCTION AND EASY-TO-VIEW USER INTERFACE, YOU CAN IMPLEMENT SPC WITH VERY LITTLE EXTRA WORK. OUR MONITORING SOLUTION IS DESIGNED TO IMPROVE THE TRACKING THE DEFECT AND CAN BE EASILY CORRELATED WITH YOUR MANUFACTURING PARAMETERS FOR ROOT-CAUSE ANALYSIS.
-
Beacon -
DG Technologies
6 High Speed CAN/CAN FD Channels 1 Single Wire CAN Channel 1 Fault Tolerant CAN Channel 2 Local Interconnect Network (LIN) Channel 1 GB Ethernet Connectivity Wi-Fi Enabled USB Connectivity On-board Media Storage Can be powered by USB, the vehicle, or 12V Power Adapter (included)
-
ZET 7160 -
ZETLAB Company
*Logical analyzer*Digital input/output, 4 bits, 0/5 V*CAN 2.0 Interface
-
ZET 7192 -
ZETLAB Company
*Analogue two-channels generator*Random profile signal formation*CAN 2.0 data interface