Showing results: 2281 - 2295 of 3398 items found.
-
VECTOR Electronics and Technology, Inc.
Boards with hole diameter of 0.042" (1.067mm) on 0.100"(2.54mm) square grid pattern. P-Pattern is available in FR4 epoxy glass, FR2 phenolic, CEM-1 epoxy glass composite and FR4 HiTg 170°C materials. P-Pattern listed below is unplated copper clad on one side, both sides or unclad with no copper on either side.
-
Arduino MKR Therm Shield -
Arduino llc
The MKR THERM Shield allows a board of the MKR family to acquire temperatures from a thermocouple of type K and a DS18Bxx digital one wire sensor. The Thermocouple is a kind of temperature sensor that offers high accuracy and a wide range of measured temperatures. Its analog nature requires specific interfacing and this shield relies on the MAX31855 thermocouple digital interface.
-
Series 115 -
Pickering Electronics
SoftCenter construction Highest quality instrumentation grade switches Plastic package with internal mu-metal magnetic screen They take up the minimum of board area, conservingboard space Insulation resistance greater than 1E12 Ohms 100% tested for dynamic contact resistance for guaranteed performance 5 or 12 Volt coils with optional internal diode
-
NEO-M8U (Qwiic) -
SparkFun Electronics
The SparkFun NEO-M8U GPS Breakout is a high quality GPS board with equally impressive configuration options. The NEO-M8U takes advantage of u-blox's Untethered Dead Reckoning (UDR) technology. The module provides continuous navigation without needing to make any electrical connection to a vehicle, thus reducing cost of installation for after-market dead reckoning applications.
-
RF9 Miniature Rosette -
HBM, Inc
Thanks to its three stacked measuring grids, the miniature SG rosette RF9 is only 5 mm in size. Its small diameter enables it to determine a biaxial stress state with unknown principal stress direction in the most confined space. The SG rosette is therefore particularly suitable for measurements on electric circuit boards or especially small components.
-
XJTAG Ltd.
The small, lightweight design means the XJLink2 can easily be moved to the Unit Under Test (UUT). Advanced features, like their programmable JTAG signal pin position, switchable power supply and auto signal skew, make it easy to connect to a wide range of circuit boards. Simple to install and use due to the USB plug-and-play ability.
-
DSX -
ARC Technology Solutions
We have developed this technology, not only for our customers, but for our own unique needs in the areas of prototyping and test. We found that many of the standard digital prototyping boards (FPGAs, PLDs, etc…) that are available on the market, did not have the flexibility or the base architecture to provide the prototyping capabilities we need in developing our own solutions.
-
3006 -
Technobox, Inc.
The Ethernet 100-FX Adapter provides a single port Ethernet connection using Fiber Optic media. An AMD 79C973 Ethernet controller provides a integrated link and physical layer for operating at 100 Mb/s. The Fiber Optic connector used on the board can be either the ?SC Duplex? style, or the ?ST RX/TX? style and is identified by the Technobox Part Number.
-
PMC230A -
Acromag, Inc.
PMC230A modules have eight 16-bit D/A converter (DACs) to provide highly-accurate analog voltage outputs. A unique two-piece board design brings the proven reliability of Acromag’s IndustryPack® (IP) A/D modules to a PMC format. An IP230A module is embedded on a PMC interface card that maintains maximum performance and transparent communication to the host.
-
2901 -
Technobox, Inc.
The 2-port Async Communications Adapter is a costeffective solution for providing additional RS232/RS422/ RS485 based serial ports for a host processor. Using configuration switches on the PMC board, each port is independently set-up at either RS232 or RS422 levels. In the RS422 case, an additional option is provided to transmit data on the receive data line in an RS485 fashion.
-
YAV90Q04 -
6TL Engineering
The interface YAV90Q04 permits to connect two YAV90096 boards to one 192-Signal contacts Quadrapaddle module. As the Mini-D 50 connectors let 2 free pins (1 and 26), these pins are interconnected to a test point, with the possibility of be grounded. Cable P/N J6200540: Mini-D-50 to Mini-D-50 IDC connectors with 400 mm flat cable.
-
ART103 -
Vadatech Inc
The ART103 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC103 carrier board. The ART103 is a passive RTM that allows for the additional connectivity of two GbE ports, Management 10/100Mbit Ethernet, Management RS-232 serial interface and three PCIe x4 lanes for expansion. One of the PMC J4s (user defined I/O) is routed to the back.
-
NC2000/4000 Series -
Noisecom
The NC2000 Series amplified noise modules are an excellent choice for high-level noise modules mounted on a circuit board. The NC2000 Series modules are housed in 24, or14-pin dual-inline packages. The NC4000 series modules are housed in a 40-pin module that cover similar noise bands to the NC2000, but have higher crest factor, and 60 dB of TTL controlled attenuation.
-
FAB116 -
Axiomtek Co., Ltd.
The FAB116 features a PICMG 1.3 CPU card slot, one PCIe x16 slot, three PCIe x4 slots, three PCI, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Two high speed USB 2.0 ports are featured. The FAB116 is compatible with Axiomtek's AX60551 and AX60552 chassis.
-
750/752 Series -
Robson Technologies, Inc.
RTI's manual test presses are compact, portable, all-inclusive, and easy to use. Single lever operation and 100% vertical compression makes the manual test press an ideal solution for PCB, hybrid module, and high pin count device-level testing when complex test requirements cannot be met with a test socket and breakout board alone.