Showing results: 2461 - 2475 of 2926 items found.
-
MultiSafe-MX -
Teledyne Gas & Flame Detection
The MultiSafe-MX system is intended for the protection of high hazard, high risk plant and facilities.The MultiSafe-MX is certified, by European laboratories, to comply with the applicable regulations.The panel is composed of dedicated cards, installed in 19” racks which have their own “intelligence”, programmed for active/passive fire protection, gas detection, intruder alarm and logic functions. Moreover, the MultiSafe-MX can interact with supervisory and SCADA systems via Ethernet, TCP/IP or Modbus.The MultiSafe-MX interfaces with devices using either conventional and/or addressable module inputs and outputs. These modules are used to tailor the system to customer requirements.
-
Comtel Electronics
2U, 19″ Rackmount system with up to two hot removable CPCI 3U Power Supplies, three Powerful Fans and CompactPCI Backplane. The system support 6U cards Front and Rear. Additional three fans are available for optimal Front and RTM cooling solution. The Backplane is compliant with PICMG 2.0 R3.0 with 64bit 66MHz and supports boards with hot swap capability PICMG 2.1 R2.0. All five CompactPCI connectors (J1-J5) are available on the backplane. The system slot is located on the lower-slot. A backplane supporting PICMG 2.16 & H.110 are available on request.
-
PICO512 -
Axiomtek Co., Ltd.
The PICO512 is designed to support the latest 7th generation Intel® Core™ processor or Celeron® processor 3965U. Coming with one 260-pin DDR4-2133 SO-DIMM socket supporting system memory up to 16 GB, the Pico-ITX motherboard also features a PCI Express Mini Card slot in support of mSATA and a pair of expansion connectors for an additional I/O board/signals. It supports a 4K visual experience with dual display outputs through HDMI and LVDS. Pico-ITX SBC can withstand a wide operating temperature range from -20°C to +70°C.
-
VL-600B -
CoolMax Technology Inc.
The VL-series is the power supply for all casual users who needs a pinch of higher than average power - 600 watts. It has all the connectors you need. PCI-E ready for your high-end graphics card, so you can have the enhanced picture you want. With the new 140mm Blue LED cooling fan for the VL-series, you can keep your system cooler and quieter than ever before. The fan comes with an automatic setting to adjust according to the heat dissipation level necessary maintaining a good balance between noise and cooling level.
-
pixus technologies
Pixus Technologies offers customized MicroTCA® shelves and system solutions. With expertise in xTCA systems, along with backplane and cooling specialists, Pixus will help you create a winning µTCA design. MicroTCA is a modular, open standard for building high performance switched fabric computer systems in a small form factor. MicroTCA systems utilize standard Advanced Mezzanine Cards (AMCs) which provide processing and I/O functions. MicroTCA targets smaller telecom systems at the edge of the network, as well as mobile, military, telemetry, data acquisition, and avionics applications.
-
EGX-MXM-P5000 -
ADLINK Technology Inc.
Meeting the needs of embedded, ruggedized, and mobile system builders, ADLINK's EGX-MXM-P5000 Embedded MXM GPU Modules utilizes Quadro Pascal architecture to deliver superior graphics and computing performance. The EGX-MXM-P5000 is specifically purposed to accommodate form factors incompatible with conventional PCI Express cards, and is built to maintain operations under a wide range of thermal and other environmental conditions. It’s the ideal choice for blade-based and other deployments where high GPU density is critical, with a choice of GPU memory capacity, extremely reasonable power requirements, and flexible display options.
-
Alpha Automation Inc.
This machine is used to test back planes used in telecommunications central stations. An operator loads a completed point to point wired back plane onto a retractable shelf on the front of the tester. Table continues and the disk falls through a hole into the bin. The shelf is pushed back into the machine where it is held in place by pneumatic operated clamps. Then a series of pneumatic cylinders sequentially insert a test card into each location in the back plane. A remote instrument performs a complete point to point continuity, short and hi pot test on all connections in the back plane.
-
ADF-D2000 -
Delphi Engineering Group, Inc
This FPGA Mezzanine Card (FMC) converts two channels of up to 2.8GHz analog input bandwidth at 1.0, 1.6, 1.8, or 2.0 Gsps and 12-bit resolution. Additionally, this FMC can be used in an interleaved mode to convert a single channel at 2.0, 3.2, 3.6, or 4.0 Gsps and 12-bit resolution. Based on the VITA 57 specification, the ADF-D1600 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
782385-01 -
NI
Screw Terminal, Ribbon, 4x128, 1-Wire PXI Module Matrix Terminal Block - The TB-2640B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2640B to the front panel I/O connectors … of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2640B also provides optional isolation resistors to protect the reed relays from capacitive loads.This 782385-01 card does NOT have 100 Ohm protection.
-
FADOS9F1 -
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
2 unique features are added to the FADOS9F1 over the FADOS71. First feature is the Programmable DC Power Supply; It can be adjusted between 0-16V and 20-1500mA with power output; the DC Voltage/Current graphs of the electronic card power supply can be produced. The second feature is the “IR Remote Temperature Measurement Sensor”; this sensor is used to find the components that heat up by drawing too much current. Using these two features together may reduce the time for trouble shooting some malfunctions by 5 to 10 times. These features can be used as a new technique for trouble shooting.
-
40-855-412 -
Pickering Interfaces Ltd.
These PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of five different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
P5563B -
Keysight Technologies
The Keysight P5563B PCIe 6.0 Protocol Test Backplane provides a convenient means for testing PCIe 6.0 add-in cards with a self-contained portable and powered passive backplane. The P5563B provides power required for all combination of exerciser and analyzer with device under test.
-
EXC-1553ExCard/Px-1760 -
Excalibur Systems, Inc.
This credit card sized interface supports up to two dual redundant 1760 channels and is compatible with all common variations of MIL-STD-1760 providing a wide range of features normally found only on full size testers.Multi FunctionEach channel of the EXC-1553ExCard/Px-1760 operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports error injection and detection. The card’s small size and compatibility with notebook computers make it the perfect solution for performing system simulation of the MIL-STD-1760 bus, in the lab and in the field. Single Function Each channel of the EXC-1553ExCard/PxS-1760 operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The EXC-1553ExCard/Px-1760 and EXC-1553ExCard/PxS-1760 cards are supplied with C drivers, including source code, Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.Note: Some laptops do not supply the average and peak power voltages required by the ExpressCard specification. The EXC-1553ExCard/Px-1760 may not function properly in these laptops.
-
Amida Technology, Inc.
The design of the GPIB control card is fully compatible with the IEEE 488.1 and IEEE 488.2 standards, using the PCI interface, supporting the Plug & Play specification, and supporting Windows 95/98/Me /NT4.0/ 2000 /XP/7 Operating system, driver function library includes Windows development software tools such as Visual C++, Borland C++ Builder, Labwindows, Visual Basic, Delphi and Labview. This GPIB-supported library provides an NI-like command control syntax format, which is convenient for users to develop and transfer applications smoothly. This interface card also provides a conversational window GPIB interface program, which is convenient for users to directly control the instrument without writing a program.
-
SCHILLER AUTOMATION GmbH & Co. KG
The Standard SD Express Memory Card Test Adapters support PCIe® 16 GT/s (Gen4) and PCIe® 8 GT/s (Gen3) Interface Compliance Program testing for SD8.0 and SD7.1. Minimal crosstalk, short trace lengths. The Micro SD Express Memory Card Test Adapters supports PCIe® 8 GT/s (Gen3) Interface Compliance Program testing for SD7.1. Minimal crosstalk, short trace lengths. They all support SDHC, SDXC, and SDUC operation modes Data collection via Lab Standard SSMP Test Cables and hard gold mating surface allow for high cycle count insertions and reliable performance.
