Showing results: 796 - 810 of 1737 items found.
-
Model 2364 -
ICS Electronics
* Model 2364-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Optional 1 'U' high Rack Mounting Kits hold one or two 2364s.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 2364s.* Optional 115750 Terminal Board and Terminal Strip for easy connections without soldering. See the Serial Accessory page.
-
CAT Advanced Series -
Amperis sl
Description The Advanced CAT Series Analyzers and Timers are stand-alone or PC-controlled digital instruments for circuit breaker status evaluation. Timing channels record arc closing and opening, resistance and auxiliary contacts. The main contact channels can also measure the resistance value of pre-insertion resistors (if present in the breaker). The advanced CAT series records graphs of the opening and closing coil currents and the movements of the moving parts of the high and medium voltage circuit breaker. Test results are printed on the 112 mm (4.4 inch) thermal printer (optional accessory) in tabular and graphical form. The advanced CAT series provides easy selection of different operating modes:
-
Model 200 -
OAI
The OAI Model 200 Mask Aligner is a cost-effective high performance mask Aligner that has been engineered with industry proven components that have made OAI a leader in the photolithography capital equipment industry. The Model 200 is a tableop mask Aligner that requires minimal cleanroom space. It offers an economic alternative for R&D, or limited scale, pilot production. Utilizing an innovative, air bearing / vacuum chuck leveling system, the substrate is leveled quickly and gently, for parallel photo mask alignment and uniform contact across the wafer during contact exposure. The system is capable of one micron resolution and alignment precision.
-
SCR ELEKTRONIKS
SCR ELEKTRONIKS have developed 4 STATIONS ENDURANCE TEST SETUP FOR THERMOSTAT OF IRONwhich is used for carrying out endurance test for thermostat of iron for the required amount of time It is very useful and handy in line testing on Mass production line as well as type Testing. It consists of Voltmeter, Wattmeter, Programmable Logic Controller( PLC ). The equipment continuously monitors faults like Contact weld and Contact Open. The other important feature is we can operate the panel in Auto Mode or Manual mode. User friendly operations make the equipment to be handled easier for any operator. This manual contains information about operating instructions and maintenance of the equipment.
-
AMETEK Sensors, Test & Calibration
We supply a range of grips and fixtures for the Chatillon force gauges. Below you will find a selection of our most popular grips and fixtures. If you cannot find what you are looking for, please contact us for a presentation of our full range.
-
310118112 -
Virginia Panel Corporation
The Keying Pin kit is a way to avoid damaging the contacts within the ITAs and Receivers. Simply insert the longer keying pins into the receiver and the smaller set screws into the ITA to create the pattern needed to isolate your test fixtures so there is no operational mismatch.
-
MR 300 C-A -
Schuetz Messtechnik GmbH
The MR300C-A micro-ohmmeter enables you to perform highly accurate resistance measurements at objects with an extremely low resistance such as cables, contacts, fuses, power connections, graphite, carbon and metal samples. In the lowest measuring range of 100 µΩ the resolution is 10 nΩ.
-
HD32MT.1 -
Delta OHM S.r.L.
Programmable datalogger able to capture and store the values measured by a series of sensors connected to its inputs. 8 analoge input, 8 digitale input, 2 puls input, potential free contacts, alarming. Programmable through software. RS485, RS232.
-
310120110 -
Virginia Panel Corporation
The Receiver for the G2 is equipped with a locking handle and nickel plated steel slides that engage up to 480 contact points. It allows a high amount of I/O within a compact and rugged device. The Receiver is accompanied by a Protective Cover to use when the ITA is not engaged.
-
Bird Technologies
Bird's RF Power Monitor family includes a range of products that not only measure power and VSWR but also provide hard contact alarms to protect your system in the event of a system failure – the IP-enabled, BPME is even capable of emailing a failure notification.
-
SG-01 -
FBGS International N.V.
The Strain Gage SG-01 is the fibre optic equivalent of an electrical strain gage. The Strain Gage SG-01 can be mounted directly on the surface of a structure by means of an adhesive. In this way, the fibre sensor makes direct contact with the surface and therefore measures directly the strain at the surface.
-
Surface Analyst -
BTG Labs, Inc.
The Surface Analyst is a fast, easy, accurate, and non-destructive instrument that quantifies your level of surface preparation from the lab to the manufacturing floor. In 2 seconds, the Surface Analyst determines the surface cleanliness level by providing the contact angle measurement and a pass/fail result.
-
MEMS Device -
Ardent Concepts, Inc.
Patented MEMS Sockets from Ardent Concepts use a unique scrubbing action contact set which is ideal for today’s sensitive MEMS devices, including accelerometers, gyroscopes, MEMS microphones and other specialized devices used in mobile electronics applications
-
GXL -
Panasonic Industrial Devices Sales Company of America
Panasonic cube-shaped GXL Micro-Size Inductive Proximity Sensors are extremely small. Each Sensor is available in four different versions: front or side sensing with normally open or normally closed contacts and offering two detection frequencies to prevent mutual interference.Characteristics
-
Panasonic Industrial Devices Sales Company of America
Power Rocker Switches for safety requirements complying with Class II EN61058-1 insulation grade. 8mm minimum insulation distance and 3mm minimum contact gap. Applications include: Vehicles, Home Appliances, Outdoor Power Equipment, Agricultural, Industrial Equipment.