Showing results: 1381 - 1395 of 1737 items found.
-
Smart I/O -
Imperious Technology Inc.
An I/O server is a software which controls and monitors one or more PLCs /RTU's using various communication protocols.Our I/O servers are built on highly optimized Windows 32bit platform. They are capable of handling very large scale SCADA systems with minimal impact on CPU usage, resulting in effective timing and usage of available hardware.Currently, we have Master and Slave solutions for DNP3 and Modbus (ASCII, RTU, TCP). Please select the appropriate tab above for more informaiton.If you are looking for a specific I/O Server, please contact us with your needs.
-
UCI-3000 -
Qualitest International Inc.
Advanced Ultrasonic Hardness Tester UCI 3000 applies ultrasonic contact impedance method to do comparative hardness measurement for testing pieces, with the high accuracy, efficiency, portability and easy operation. UCI 3000 is a high-precision portable device for quick measuring hardness of small fogging, cast material, weld inspection, heat affected zone, Ion-nitride stamping dies and molds, forms, presses, thin walled parts, bearings, tooth flanks, etc. It is used for measuring the hardness within the ranges of main hardness scales – HB, HRC as well as HV.
-
SENTRY -
Edgetech Instruments
The Edgetech Instruments Model SENTRY detects upset conditions in compressed air systems by constantly monitoring dew point and pressure at the system header or dryer output. The SENTRY alarms when a loss in pressure or high dew point is detected. This information is valuable in detecting compressor failures, system leaks, or drops in dryer performance. A pulsing audible alarm and strobe lamp provide quick notification of upset conditions. The SENTRY also provides a local display of pressure, dew point and system status as well as 4-20mA analog output and alarm relay contacts.
-
HS-120 -
Standard Electric Works Co., Ltd
● Used for the extraction of fuses, isolators & fuse switch disconnections.● Can be attached to the 275 HP Proximity Detectors and contact Capacitive Detectors 21× HVD.● Universal "sunrise" head attachment to fit special tool fittings.● Head Section rated at 100kV per 300mm (5 min).● Comes complete with sunrise fitting and fuse extractor.● 3 × 1.8 meter sticks; 1 × 1.2 meter head section.● Sticks 1 × 1.2 meter head section complete with universal sunrise fitting. ● 1 × carry bag. ● Meets IEC 60855.
-
Virginia Panel Corporation
The 9025TR has over twice the I/O as the G12 and is outfitted with the same 20-inch platform to support enclosures while engaging and disengaging. The front-mount ITA is user-friendly, allowing the enclosure or fixture to be fastened from the mating side. The docking feature of the 9025TR provides an easy way of guiding a fixture into position prior to engagement. Runners along the platform provide a smooth-sliding action, ideal when using fixtures up to 180 pounds. The 9025TR uses all standard modules and contacts, includes a microswitch and is available with optional table legs and keyboard tray kit.
-
PD-28 -
Standard Electric Works Co., Ltd
● Measures both AC and DC voltages with digital multitester.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.
-
PD-20 -
Standard Electric Works Co., Ltd
● Measures both AC and DC voltages with digital multitester.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.
-
A.H.Systems, Inc.
Conducted currents can be measured without making direct contact with the source conductor or metallic surface by means of clamp-on broadband current probes. The BCP-5xx EMC Current Probes are designed to permit field intensity meters, spectrum analyzers, and other 50W impedance instruments to measure quantitative magnitudes of current.
-
CAMI Research Inc. (CableEye®)
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Pulse Electronics
Pulse’s complete offering of LTCC based Band Pass Filters, Balun’s, Diplexer’s and Couplers used in conjunction with our wireless antenna products will enhance your devices performance keeping attenuation and noise to a minimum. Many of Pulse’s IPD components are already qualified or referenced on various radio designs, so please contact us about the components already qualified on the radio you are using. From Wifi Networking devices, to smart phones and tablets, Pulse’s offering of IPD Components has you completely covered. Using the table below you can search our complete IPD Component offering.
-
Head & Torso Simulators -
Listen Inc
If you need to carry out realistic in-situ measurements of headphones, telephones or hearing aids, you need a Head and Torso Simulator such as the B&K ‘HATS’ – Type 4128D or GRAS’ Kemar to complete your test setup. These manikins have built-in ear and mouth simulators that provide a realistic reproduction of the acoustic properties of an average adult human head and torso. They are commonly used for tests on telephone handsets, headsets, audio conference devices, microphones, headphones, hearing aids and hearing protectors. Please contact your sales engineer or email sales@listeninc.com for more information.
-
TCT101-1ABC -
Datexel
The Process Timer TCT101-1ABC is a panel mount 4 digit 2 line display meter that can be set up for various Timer functions, such as Timer Off, Timer On, Pause Timer, Timer On and Off, Propotinal Timer. The TCT101-1ABC has 2 relays that can be used for various functions and has 5 Amp contacts. The timer periods can be set in multiples of 1 hundredths, 1 tenths of a second, seconds, minutes or hours. With the aid of the front touch panel or digital input it is possible to interrupt the timer. The unit also has a function that can set the output to toggle on and off over a period of time.
-
Teledyne Marine ODI
The Angled Physical Contact Rolling Seal 8 Connector (RS8 APC) from Teledyne ODI is a wet-mateable optical connector with angled endfaces. The design reduces signal interference due to reflections at the connector face, supporting the next generation of subsea optical communication equipment. The Rolling Seal design provides isolation from seawater and silt when the connectors are unmated. As the seals rotate, the fibers join inside a clean, oil-filled conduit, resulting in a reliable optical throughput. The RS8 APC incorporates RS8 Mark III design features to enhance operational efficiency and reduce risks during ROV intervention.
-
Alpha Moisture Systems
Alpha Moisture Systems' range of single channel moisture analysers have been developed to meet the requirements of all applications, requiring on-line analysis at a single sample point. These instruments combine robust construction and advanced electronics to ensure that they will provide accurate moisture analysis through a long and reliable service life.Unless stated otherwise, all on-line analysers are used in conjunction with any of our range of dedicated Ultra High Capacitance moisture sensors covering an overall range from -110ºC to +20ºC dewpoint, 0.001 to 23,000 ppm(v). Please contact us for further information.
-
Shenzhen Graigar Technology Co.,Ltd.
Measurement of the speed of a rotating shaft is a common requirement in many industrial and laboratory applications. Such measurements have usually been carried out in the past with the help of contact type tachometers with friction drive. More recently digital optical non-contact tachometers have been designed which count the reflected pulses from a white patch on the shaft and then display the speed in rpm. The light source is usually a filament lamp operating with dry cells leading to limited life and illumination. A similar ideawith magnetic pick-up from a particular area of the shaft has also been used for speed measurement.
