Filter Results By:
Products
Applications
Manufacturers
-
product
Hand-Held Alternator/Battery Load Tester
6024
• Full 125 Amp load tests 12 Volt and 24 Volt Batteries, alternators and starters on all types of vehicles• PATENTED• Made in USA of US and Global Components
-
product
AATCC Wrinkle Recovery Tester
M272
To determine a fabric's ability to recover after wrinkling under a predetermined load for a set period of time. Set of 3-D plastic replicas are available to grade fabrics.
-
product
Qualification Tester
LQ402
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 6 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 2 cabinets. One is for the electronic components with the primary measurement devices and the other one holds the 6 load boxes.
-
product
Advanced Diagnostic Load Cell Tester
LCT-U
The Advanced Diagnostic Load Cell Tester Model LCT-U is a stand-alone hand-held device specially designed for fast, comprehensive troubleshooting of strain gauge load cells. The LCT-U can quickly diagnose problems with all common types of load cell available today, including 6-wire load cells (with sense wires).
-
product
Wheel Running Tester up to 15000 kg axle load
MINC II EURO | VP 420005
Maschinenbau Haldenwang GmbH & Co. KG.
The test lane-compatible MINC II EURO guarantees a verification of the axle geometry in seconds when the test vehicle drives over (up to 15.0 t axle load) as well as a fully automatic evaluation of the deviation in m / km. The measured values are displayed either in analog form on a dial or by transmission to a PC screen (including graphic representation).
-
product
Wrinkle Recovery Tester
TF112 AATCC
TESTEX Testing Equipment Systems Ltd.
AATCC Wrinkle Recovery Tester is used for determining a fabric's ability to recoverafter wrinkling under a pre-determined load for a set period of time.Provided with a set of 5x3 dimensional plastic replicas to grade fabrics 1-5.
-
product
Tribometers & Mechanical Testers
Research into materials and how materials can be changed to influence strength, integrity, or durability is an integral part of product design and improvement across nearly every industry. Bruker's mechanical testers and tribometers provide the most comprehensive and versatile means of investigating tribology—friction, wear, load, hardness, and lubrication.
-
product
Inductive Load Tester
4602-LV
There is a tendency that MOSFET has Low On Resistance so that it demands that Inductive Load Tester to have higher forcing current for measurement. The forcing current is limited by forcing voltage with previous test method. Thus it becomes difficult to test this kind of middle power range devices.
-
product
MBT 4000 Series
Maschinenbau Haldenwang GmbH & Co. KG.
Roller-Brake-Tester up to 13000 kg axle load
-
product
HiPot Calibrator
Model 9102
The 9102 Hipot Calibrators is specially designed standard devices for instrument calibration lab. The 9102 can simulate multiple loads and apply to various Hipot testers. These calibration equipment can save manufacturers a great deal of regular calibration fee.
-
product
MBT 7000 Series
Maschinenbau Haldenwang GmbH & Co. KG.
Roller-Brake-Tester up to 18000 kg axle load
-
product
LED Testers
PeakTech Prüf- und Messtechnik GmbH
An extremely practical component tester for LEDs and other components. The device outputs an automatically raised output voltage between 0 to 300 V DC, which adapts to the connected load so that the sensitive components are not destroyed. Particularly suitable for the service and repair workshop.
-
product
MBT 6000 Series
Maschinenbau Haldenwang GmbH & Co. KG.
Roller-Brake-Tester for tractors up to 18000 kg axle load
-
product
Digital Roller Brake Tester for Cars and Vans up to 5.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,800mm
C_MBT C 5.0 W280 | VP 210160
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 5.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,800 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for large and heavy cars and vans, and with increased loads.
-
product
Hipot Current Calibration Load Resistors
HPRS-HIPOT-LOAD
The IET HPRS-Hipot-Load is an excellent replacement for the Fluke 5320A-Load Hipot current calibration load resistors. The IET high power resistive load can be used with the Fluke 5320A Multifunction Electrical Tester Calibrator or standalone. It provides a high power and high voltage load to various hipot tester to create the leakage current needed to calibrate various manufactures hipot testers.
-
product
PC Based Rotor Tester
GTS 1000
The PC Based Rotor tester is the most reliable, fast and cost-effective way to detect faults in the Rotors in less than 10 seconds. This Rotor Tester can Test Large sized Rotors of any Size, Length & Weight that can be mounted on a Load balancing machine or a Lathe and rotated at a speed of 600 rpm.
-
product
Martindale Abrasion and Pilling Tester
Sataton Instruments Technology CO., Ltd
By providing a defined load, a translational movement tracing a Lissajous figure and abrasive medium, martindale abrasion tester is professional designed for determining of the abrasion resistance of fabrics including specimen breakdown, mass loss and appearance change. The tester can also use to determine the resistance to pilling and surface change of textile fabrics. With accessories, the tester is to determine abrasion resistance of lining and insock for personal protective footwear. It is widely used to evaluate the properties of clothes fabrics, coating materials, wool fabrics, nonwovens and other special materials for protective equipment.
-
product
Digital Roller Brake Tester for Cars and Vans up wot 3.5 T Axle Load with 2 x 3 kW Drive Motors and Max. Track Width of 2,200 mm
C_MBT C 3.5 W220 | VP 210152
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 3.5 t axle load with 2 x 3 kW drive motors and a max. track width of 2,200 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes.
-
product
Four Channel Load Cell Tester
LCIC-4HS
Industrial Measurement Systems Ltd.
Four Channel Load Cell Interface Card Model LCIC-4HS The LCIC-4HS is a four channel load-cell interface board for the IBM PC/AT and compatible computers (ISA Bus). This board was especially designed to fit very fast and real-time weighing applications such as multi-head fillers. It supports up to four channels with one load-cell on each. All the necessary filters and the batching control functions are built on the board and are easily accessible by the user. Direct communication with the PC bus and high-frequency sampling enables the LCIC-4HS to handle all real-time applications and to achieve very high accuracy. The LCIC-4HS is memory-mapped. Up to 32 boards (128 channels) may be installed in a single PC. It comes with a detailed user manual and software utilities for easy installation and calibration as well as full examples for the programmer (including Win 95/98 drivers).
-
product
Pull tester for Dade County Protocol PA 105-A
FIXUROOF 300
The Fixuroof portable pull-tester is an accurate unit, designed for testing in the field the pull-out force of base ply fastener. Easily determine whether the mechanical fastener provides sufficient resistance to static uplift force to meet the wind load requirements.
-
product
Auto Bursting Strength Tester
TF142A/B
TESTEX Testing Equipment Systems Ltd.
Auto Bursting Tester, to determine the bursting strength of fabric, woven or knitted fabrics, non-woven, paper and board by the Application of hydraulic load under a rubber diaphragm of a specific area.
-
product
MBT 1000 Series
MBT 1000 EUROSYSTEM | VP 610012
Maschinenbau Haldenwang GmbH & Co. KG.
The MBT 1000 EUROSYSTEM roller brake tester is used to test the brakes of single and two-lane vehicles such as motorcycles, trikes and quads with a wheel load of up to 1.0 t. Due to its short roller spacing, it is also especially suitable for testing small two-wheelers. Its MAHA modular design enables an optional motorcycle clamping and holding device for the rear and front wheel, whose removable clamping jaws ensure simple and rim-friendly testing.
-
product
Hamburg Wheel-Tracking Tester
The Hamburg Wheel-Tracking Tester is used to test submerged, compacted Hot Mix or Warm Mix Asphalt specimens as per standard.The device consists of a reciprocating wheel that is rolled over the specimens while measuring the rate of permanent deformation. A constant load of 705 N ±4.5 N is applied to the specimens with a sinusoidal wheel speed of 1 ft/sec in a constant temperature controlled water bath up to 70 °C (± 1.0 °C). An LVDT jig is used for continuous measurement of permanent deformation along the path of the rolling wheel. Accommodates cylindrical or slab specimensSoftware for automatic determination of Stripping inflection PointNumber of passes to SIP, number of passes to failure and other calculated parametersStainless steel construction with temperature controlled water bath up to 70ºC
-
product
Battery Load Tester
Battery Beak
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
product
Digital Load Calibrator
HS 2000
Jinan Testing Equipment IE Corporation
The load cell calibrator is used to calibrate the load of testing machine and hardness tester, and also can be used for force measuring. It is digital display type with high accuracy of less than +0.3%, and easy to operate
-
product
Unclamped Inductive Load Tester
ITC55100C
The system has been designed around a very powerful micro-controller that gives it a timing resolution of 40ns, twenty times faster than the previous model. Its response time to the peak and zero current is improved ten times. Combined this gives greater accuracy for the charging and avalanche times and for the reported peak drain current.
-
product
Digital 130AMP Battery/Alternator Tester
MD4780
For testing 6V and 12V batteries, charging systems, alternator diodes and starter. Industry leading 130 amp load .
-
product
MBT 3000 Series
Maschinenbau Haldenwang GmbH & Co. KG.
Roller-Brake-Tester up to 8000 kg axle load
-
product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,200mm
C_MBT C 4.0 W220 STOCK | VP 210165
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,200 mm.Basic version - available ex stockincl. specific option package.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes.
-
product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,200mm
C_MBT C 4.0 W220 | VP 210156
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and Vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,200 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes with high vehicle throughput and increased loads.
