Showing results: 2176 - 2190 of 7546 items found.
-
PeakTech Prüf- und Messtechnik GmbH
Practical built-in module as voltmeter with freely definable measuring range from 0 to 200mV, 2V, 20V, 200V or 500 V. Current measurements from 0 to 200µA, 2mA, 20mA, 200mA and 2A can be carried out via a shunt. With the snap-in frame, this inexpensive module can be integrated into any front panel of your own construction.
-
EZ-TAP™ PRO RS-232 -
Stratus Engineering Inc.
Stratus Engineering’s EZ-Tap Pro hardware module RS232 sniffer is a sophisticated protocol analyzer and bus analyzer hardware solution that overcomes latency and time-tagging problems associated with traditional dual COM port monitoring solutions.
-
Dynamic Engineering
The Cable Assembly Crypto / Tape provides a method of interconnecting the IP-Crypto and IP-Tape from the carrier to the PCI Bezel [rear IO] when installed into a PCI machine. Most IP Carriers have 50 pin headers suitable for ribbon cable in use for the IP Module IO. The headers are located on the carrier and internal to the chassis. Interconnecting to the outside world can be an issue.
-
540103010258 -
Virginia Panel Corporation
This cable assembly comes with PCB adapter 510150210 and a Mini Coax module to 4 SMB plugs.
-
Ecom Instruments
To measure a wide range of pressure in an explosive endangered area the range of pressure modules is extended with 8 ATEX compliant models.
-
Time Electronics
CalBench is a custom built work station for industrial test facilities and calibration laboratories. A wide range of modules for calibration of electrical, pressure, temperature, and loop are available. Further modules and extras such as power supplies, oscilloscopes, and counters can also be integrated. CalBench provides the versatile solution to multi product calibration that meets the highest industry standards.
-
CalEasy Series -
Marvin Test Solutions, Inc.
CalEasy is a full-featured, Calibration Executive software package that supports the verification and calibration of Marvin Test Solutions instruments. The software is intended for use by users that prefer to perform in-house calibration and verification for their Marvin Test Solutions instruments. By calibrating or verifying the instrument in-house, the time and cost associated with returning an instrument to Marvin Test Solutions for calibration service can be eliminated or reduced. CalEasy is also used internally by Marvin Test Solutions production to perform initial calibration and to recalibrate the instrument when received for service. This ensures that user and factory based calibration performance is similar. Depending on the specific instrument, standards instrumentation supported for calibration / verification includes a DMM, and a frequency standards module. Some modules require the use of matrix switch card.
-
CAP CAL -
Altanova Group
The purpose of CAP-CAL is to check the correctness of Tan Delta and Capacitance of TD 5000 and TDX 5000. The calibrator includes an extremely high accuracy high voltage capacitor, which comes with a certificate issued by ISA - Altanova Group lab.
-
Arptel Call -
Arptel
Arptel Call is the call generator module in the NetSense suite. NetSense is Arptel's next generation platform, designed to be flexible, versatile and scalable. NetSense is a webbased platform supporting several different browsers on different operating systems. NetSense also has multi-time zone and multi-language support.
-
W-IE-NE-R, Plein & Baus GmbH
CAMAC - "Computer Aided Measurement And Control" is a joint specification of the U.S. NIM and the European ESONE committees. CAMAC was introduced in 1969 by ESONE and fully defined in 1971 with the standards EUR4100 and EUR4600.
-
CMDGG8 -
W-IE-NE-R, Plein & Baus GmbH
The CMDGG-8 is a multi functional FPGA based delay, logic and timing module which provide often needed functions such as gate, delay & pulse generator, logic fan in / fan out, coincidence register and scaler / pre-scaler.
-
CFB -
W-IE-NE-R, Plein & Baus GmbH
The WIENER CFB is an intelligent, programmable, re-configurable CAMAC-to-FERA bridge with sequencer that allows one to interface both, common and custom-made CAMAC modules to FERA-readout-based data acquisition systems.
-
W-IE-NE-R, Plein & Baus GmbH
Power adapter to use a NIM module within a CAMAC crate. Provides all 6 voltages to the NIM module. Available also in a versions with 12V DC-to-DC converter for CAMAC chassis without +/-12V.
-
CAML-MOD3 -
Curtiss-Wright Defense Solutions
Even for simple applications, getting data into an FPGA structure can be critical. CAML-MOD3 simplifies CameraLink interfaces through a simple adaptor directly into and under control of a host FPGA, such as an XMC-FPGA05D.
-
XM Bond HR -
Viscom AG
Viscom AG offers the new XM Bond HR camera module for dependable inspection of wire bonds. Its characteristics include a 21 mm x 21 mm field of view size and exceptionally fine detail resolution. It is ideally suited for the most precise inspection of thin wires in the production line. With the new XM Bond HR camera module, Viscom advances the configuration possibilities in wire bond inspection for higher in-line inspection quality. This module is particularly recommended for safety-relevant electronics, where thin wires with diameters of e.g. only 20 µm are installed. Products of this kind find use, among others, in various types of signal processing in the automotive and aerospace sectors. The high-quality optical components and sensor chips with first-class resolution and sensitivity achieve superb image quality and sharp detail resolution. Together with its 21 mm x 21 mm field of view size, the XM Bond HR offers a resolution of 4.5 µm per pixel. A telecentric lens ensures that regardless of the distance to an object, an inspection window has the same image scale; for example, the end points of an inspected thin wire are always located at the same positions in the inspection window. In addition, the telecentric optics also prevent areas on the electronic assembly next to tall components from being hidden.