Showing results: 4141 - 4155 of 7546 items found.
-
40-220A-101 -
Pickering Interfaces Ltd.
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
40-220A-802 -
Pickering Interfaces Ltd.
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
40-220A-302 -
Pickering Interfaces Ltd.
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
40-220A-602 -
Pickering Interfaces Ltd.
Versatile PXI Breadboard with 65 sq cm (10 sq in) of Prototype Area, fitted with 15-pin D-type connector, dual PXI slot width.
-
40-882A-004 -
Pickering Interfaces Ltd.
The 40-881A-004 is a quad 50Ω 4 to 1 RF multiplexer with 8GHZ bandwidth.The 40-881A range of multiplexers have automatic termination of unused signals and are available as a single MUX in one PXI slot, a dual MUX in two PXI slots, or triple and quad MUXs in three slot PXI modules.
-
40-835-001 -
Pickering Interfaces Ltd.
The 40-835-011 is a single 75 Ohm 16-channel RF MUX in a single PXI slot. The module has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40-835 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
SORAS LS -
PSE Instruments GmbH
In certification laboratories for photovoltaic modules, steady-state solar simulators are mostly used for stabilization / light soaking tests (MQT 19) and hot-spot endurance tests (MQT 09) according to IEC 61215 and IEC 61730. An initial stabilization is required for all PV modules that undergo a standard test procedure. For the hot-spot endurance test (MQT 09), it is important that the operator has easy access to the front and back site of the module. During the test, it is necessary to shade one cell after each other to take infrared pictures, which requires good visibility of the entire back side. Our swiveling module holding system enables easy access to the front and back side of the module.
-
PSE Instruments GmbH
In PV modules, many different components are exposed to the sunlight. Therefore, the IEC 61215 defines a UV preconditioning test (MQT 10) to test whether these components can withstand the UV radiation of the sun. In our test chamber, the UV radiation is up to five times the sun intensity to accelerate the test, as requested in the UV preconditioning test.
-
PSE Instruments GmbH
Solar modules and collectors, whether on roofs, in façades, or freestanding, are often exposed to high mechanical stress or load: A deep layer of snow or strong winds can greatly affect the materials and connections. Mechanical load test stands accurately test the durability of PV modules and thermal solar collectors.
-
HIT -
PSE Instruments GmbH
Hailstorms can cause severe damage to modules and collectors. Our test stand enables you to carry out tests according to international standards. The hail impact test stand uses an air-pressurized launcher that shoots ice balls representing hailstones of a predetermined size at the module or collector mounted on the support frame.
-
PSE Instruments GmbH
The connection between the laminate and all other components of a PV module are essential for a high durability and long lifetime of PV modules. Only when the laminate protects the electrical components from humidity and water is a good insulation guaranteed.
-
PSE Instruments GmbH
PSE AG has developed an electrical safety test that combines different tests for the testing of PV modules. With our four-in-one tester it is possible to test the following according to IEC 61215-2 and IEC 61730:
-
BDT -
PSE Instruments GmbH
Our bypass diode thermal tester is designed to assess the adequacy of the thermal design and long-term reliability of PV modules bypass diodes, which are used to limit the detrimental effects of module hot spot susceptibility.
-
MBT -
PSE Instruments GmbH
The tester is used to provide confidence that the risk of physical injuries can be minimized if the PV module is broken in its specified installation. The module breakage test is specified in the IEC 61730 (MST 32).
-
PSE Instruments GmbH
Quality control in production lines of PV modules is an essential factor for long-lasting cutting edge products. Electroluminescence images, high pot testing and power measurements are the most important parts of the quality control.