Showing results: 2161 - 2175 of 10250 items found.
-
Pickering Interfaces Ltd.
Our 2 Amp PXI Large Matrix Modules use high-quality electromechanical relays to achieve their 2A switch rating. The BRIC structure allows the creation of large PXI matrices over multiple slots without the use of expensive external cables. The fully integrated programming interface represents the matrix as a single entity, easing user programming and reducing the likelihood of user errors.
-
778985-01 -
NI
4-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/4 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
ABex TM-1149Cx -
Konrad Technologies GmbH
The ABex TM-1149Cx is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C2/X or SFX/PXI(e) 1149/C4/X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan cards it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
N7550A -
Keysight Technologies
The N7550A is part of Keysight’s family of value-line electronic calibration (ECal) modules that makes calibration of vector network analyzers fast, easy and accurate. Cut your calibration down to half the time it normally takes using a traditional mechanical cal kit. Simply connect it to your instrument and the firmware does the rest. For greater precision and higher accuracy measurements consider the N44xx and N469x family of ECal products.
-
781752-01 -
NI
1-Port Gigabit PXI Ethernet Interface Module—The PXI‑8231 provides a Gigabit Ethernet interface with up to 1000 Mbit/s transfers. With 1000 Mbit/s Gigabit Ethernet, you achieve a substantial performance increase over 100 Mb/s Fast Ethernet while remaining completely compatible with 10BASE‑T and 100BASE‑TX Fast Ethernet networks. The PXI‑8231 also features automatic cable polarity detection.
-
AMP3060 -
Exodus Advanced Communications
Best in Class SSPA model AMP3060 - a 32 to 40GHz, 10W GaAs Hybrid SSPA Module. It provides 10W CW Psat over the full band with 4.0dB Peak to Peak flatness. Additional features include high reliability and ruggedness along with suitability for all single channel modulation standards. This amplifier is designed for any application that requires wide band coverage such as EMI/RFI, KA band Radar, EW and High Power Millimeter Testing.
-
ABex TM-1149Cx-FXT -
Konrad Technologies GmbH
The ABex TM-1149Cx-FXT is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C4-FXT-X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan card it’s possible to connect up to four JTAG/Boundary Scan TAPs. All differential signal wires on the PCB are impedance controlled. In addition, all other digital signals (PIP, TRG, Aux, I/O) and Ground can be switched off via relays.
-
iWave Systems Technologies
iWave’s Cyclone V based 6U cPCI Card is a rugged standalone module complaint with 6U size CPCI PICMG 2.0 Rev 3.0 backplane, aimed for the high-speed data, video processing, and display applications. The card offer speed up to 512MB/s of DMA transfer and up to a 6 channels of transceiver interfaces capable of operating up to 6 Gbps, SFP, Built-in health monitoring circuits, DVI Input, and Output Interfaces
-
778739-01 -
NI
The PXI‑2529 is a high‐density PXI matrix switch module that you can configure as either a 4x32 or 8x16 2‑wire matrix by using different terminal block accessories. It uses electromechanical relays that offer excellent performance for high-power signals and low thermal offset for accurate measurements at low-voltage levels. The PXI‑2529 also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
40-261-001 -
Pickering Interfaces Ltd.
PXI programmable resistors featuring fine resistance setting resolution and excellent resistance stability and accuracy through the use of advanced switching networks and software correction techniques. The two modules in this range support two identical resistor channels t that can be set to values of between 1.5Ω to 2.9kΩ or 10Ω to 36kΩ with a precision of better than 2mΩ (this version) or 15mΩ (40-261-002) making them ideal for simulating sensors that can be accurately controlled to fine values.
-
Virginia Panel Corporation
The 9050 VXI Solution is designed for use with VPC's pre-wired interconnect adapters on the top tier and discrete wiring modules on the bottom tier. The receiver opens downward via hinges to give the user access to the instruments in the rack. A microswitch, which comes standard, allows for shut off any power going through the system before removing the ITA. Using a plug and play plate or a flange kit allows for easy mounting of the receiver to any 19” rack system.
-
40-261-002 -
Pickering Interfaces Ltd.
PXI programmable resistors featuring fine resistance setting resolution and excellent resistance stability and accuracy through the use of advanced switching networks and software correction techniques. The two modules in this range support two identical resistor channels that can be set to values of between 1.5Ω to 2.9kΩ or 10Ω to 36kΩ with a precision of better than 2mΩ (40-261-001) or 15mΩ (40-261-002- this version) making them ideal for simulating sensors that can be accurately controlled to fine values.
-
Pickering Interfaces Ltd.
Pickering's PXI Fault Insertion / Signal Insertion Switch Modules feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect all of which can simulate connectivity problems in the system. Two switching topologies are available: *Single signal paths with series switches and switches to connect to one or more fault buses*Pairs of signals with series switches, shorting switches between the signal pairs and switches to connect either signal to an external fault input.
-
40-584-001 -
Pickering Interfaces Ltd.
Our model 40-584, along with the following models40-584, 40-585, 40-586A and 40-587Aare high-density single pole PXI matrices each supporting 256 crosspoints. All models use gold-plated contact electromechanical relays. The PXI matrix modules are designed for switching medium voltage and power signals. The user signal connection is via a robust 78, 50 or 37 pin D-Type or 160 pin DIN 41612 connector that is fully supported by the wide range of our cable and connector accessories.
-
40-330-003 -
Pickering Interfaces Ltd.
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.