Showing results: 7141 - 7155 of 10250 items found.
-
34921A -
Keysight Technologies
The Keysight 34921A module for the 34980A Multifunction Switch/Measure Unit is the most versatile multiplexer for general purpose scanning. It has low thermal offset characteristics and a built-in thermocouple reference on the terminal block, making it ideal for temperature measurements directly to the internal DMM. The dense, multi-function switching with 100 channel/second scan rates addresses a broad spectrum of data acquisition applications.
-
ROM-5722 -
Advantech Co. Ltd.
Advantech ROM-5722 SMARC 2.1 Computer-on-Module is powered by NXP i.MX8M Plus SOC which includes up to 4 Arm Cortex-A53 cores in combination with one Cortex-M7real time processor and Vivante GC7000UL graphics engine. It provides USB2.0, USB3.2 Gen1By1, Gigabit Ethernet, MIPI-CSI, PCI Express, Dual channel LVDS shared with MIPIDSI for embedded applications.
-
ROM-6881 -
Advantech Co. Ltd.
The Advantech ROM-6881 SMARC 2.1 Computer-on-Module is powered by a Rockchip RK3588 SoC which includes Quad Arm Cortex-A76 and Quad Cortex-A55 processors, 6Tops NPU and a high-performance Arm Mali-G610 3D graphics engine. ROM-6881 supports 8K @ 60 fps H.265/VP9 video decoding, and 8K @ 30 fps H.265/H.264 video encoding.
-
SY8800 -
CAEN S.p.A.
- Factory configured modular system- 5 free slots for power supply modules- 3U x 19″ x 35 cm crate size- Floating channels- Local and Remote Control- Remote control via Ethernet, USB, CANBUS and RS232- Max output power: 2.5kW @ 220Vac, 1.5kW @ 115Vac- Up to 8 independent channels- Low noise
-
WFD16 -
APPLICOS
The WFD16 is a 16 bit Waveform Digitizer for high-speed / high resolution waveform capturing and analyzing. The fully differential signal path ensures an exceptional high signal quality. Despite this emphasis on signal quality the WFD16 also has a good DC accuracy. The module features differential inputs with a 50 Ohm or 10 kOhm termination and a with a programmable common-mode voltage.
-
41-761-002 -
Pickering Interfaces Ltd.
The 41-761-002 is a low voltage 24-channel output module ideal for simulating theoperation of a thermocouple, also available with 32, 16 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
41-761-001 -
Pickering Interfaces Ltd.
The 41-761-001 is a low voltage 32-channel output module ideal for simulating theoperation of a thermocouple, also available with 24, 16 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
41-761-003 -
Pickering Interfaces Ltd.
The 41-761-003 is a low voltage 16-channel output module ideal for simulating theoperation of a thermocouple, also available with 32, 24 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
75SBC4 -
North Atlantic Industries
NAI’s 75SBC4 is a 3U cPCI NXP™ QorIQ® P2041, PowerPC-based, Single Board Computer (SBC) with dual, high-speed/high-performance function module slots for configurable multifunction I/O interface expansion. Ideally suited for rugged defense, industrial, and commercial applications, this low-power, cost-conscious, SBC delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
EDFA -
Optoplex Corporation
Optoplex designed and produced high power single-mode and polarization-maintaining EDFA, which met MSA compatible requirements. C-band MSA EDFA Module with +23 dBm Output Power is Optoplex standard product. Optoplex designed Pre-EDFA provides more than 35dB gain with -40dBm input power. The Double-Cladding pumped EDFA produces 2W output power.
-
Acery Technologies
The RF / MW switch includes a variety of RF and microwave switch modules - RF multiplexers, which are available for use in the 34980A multifunction switch / measurement unit, providing broadband switching from DC to 20GHz . Use these modules to route test signals between your device under test and a signal source, oscilloscope, spectrum analyzer, or other instrument. The switch / attenuator driver module also controls the external switches and attenuators of the 34980A.
-
VDM Series -
Cytec Corp.
Cytec's VDM Series of video and RF switching systems are based on a solid state switch fabric and are available in non-blocking, full fan-out configurations of 8x8 to 32x32, with a small signal bandpass of 400MHz. Input and output buffers can be modified for different impedance or signal levels. Both the switch modules and control modules are modular for ease of expansion and low MTTR. Start with an 8x8 matrix and expand to a 32x32 simply by adding additional input and output modules.
-
MST-8101/8103 -
Matrix Technology Inc.
Multi-channel output is an internal high-voltage switching module attached at the bottom of the instrument. Through multi-channel output module, multiple test points of the components can be connected with multiple channels at a time. During testing, the instrument can be set to control the channel switch. Controllable testing can be achieved by connecting the corresponding port to withstand voltage test terminal. With this multi-channel module, rapid connection can be achieved through test fixture without changing ports during the testing process.
-
FS2354 & FS2355 -
FuturePlus Systems
The FS2354 and FS2355 are logic analyzer probes used to test DDR3 SO-DIMM memory modules. When used with the triggering and analysis capabilities of Keysight’s Logic Analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR3 SO-DIMM systems.
-
980 Series -
Teledyne LeCroy quantumdata
The Teledyne LeCroy quantumdata 980 series Advanced Test Platforms are module based systems that can accommodate multiple 980 series modules. There are two (2) 980 platforms available. The 980 series platforms and associated modules can be controlled either through the PC-based 980 GUI Manager or through the embedded 980 GUI Manager running on the 980B or 980R platforms’ built-in color touch screen. The 980 GUI Manager provides a graphical user interface (GUI) to control the instrument and view status. The embedded GUI Manager enables you to view incoming video and metadata in the Real Time mode when using any of the 980 modules with an analyzer function.