Showing results: 301 - 315 of 626 items found.
-
CU-U Series -
Mors Smitt Group
The CU-U is a so called safety relay which is used in places where a safe separation between coil and contact circuit is required. The relay is, with the corresponding screw socket V12, according to CEE 15/2e edition, approved by KEMA, for application in gas fired installations.
-
DPM 400 -
Lascar Electronics Ltd
The DPM 400 is a 3 digit LCD voltmeter with 10mm (0.39") digit height and annunciators. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into a DIL socket or can be panel mounted using the snap-in bezel and window.
-
410112375 -
Virginia Panel Corporation
The Enclosure for the 50 module ITA is made of aluminum, painted black and secured to the ITA by eight socket head cap screws (included). The top of the enclosure is a hinged cover plate with quarter turn hardware that provides easy access to the ITA’s wiring when required.
-
410112199 -
Virginia Panel Corporation
The Enclosure for the 50 module ITA is made of aluminum, painted black and secured to the ITA by eight socket head cap screws (included). The top of the enclosure is a hinged cover plate with quarter turn hardware that provides easy access to the ITA’s wiring when required.
-
1924 -
Peaceful Thriving Enterprise Co Ltd
*Check on 12V systems. *Quickly check continuity of dead circuit, sockets, door bells, motors, switches, fuses and other high voltage appliances.
-
AMZC-304 -
Amperis sl
Short circuit loop impedance measurement in networks with nominal voltage: 220/380V, 230/400V, 240/415V, with frequency 45…65Hz ; Short circuit loop impedance measurement with 15mA current, without triggering RCD. ; Detection of the replacement L and N in the socket and automatic swap in the meter
-
DPM 340 -
Lascar Electronics Ltd
The DPM 340 is a 3 digit LED voltmeter with 8mm (0.31") digit height. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into a SIL socket or can be snapped into a panel. Connection to the meter is via a single row of pins
-
40-965-911 -
Pickering Interfaces Ltd.
The 40-965-911 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 8 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of 100 BaseT Ethernet signals.
-
DPM 500 -
Lascar Electronics Ltd
The DPM 500 is a 3 digit LCD voltmeter with 12.5mm (0.5") digit height. It features 200mV d.c. full scale reading, auto-zero, auto-polarity and a set of annunciators. The meter plugs directly into a DIL socket or can be panel mounted using the snap-in bezel and window.
-
1937 -
Peaceful Thriving Enterprise Co Ltd
The AC line splitter is a helpful testing device for electrician. Electrician can measure the current with clamp meter through the X1 and X10 measuring rings. X1 is 1:1 measurement, and X10 is ten times (1:10) of the actual current, which is helpful for small current measurement. This device also combines the function of socket tester and GFCI tester, which means electrician can use this tester to test socket and load at the same time.
-
SparkFun Electronics
Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next MP3 project! Board comes fully assembled and tested.
-
SP 200 -
Lascar Electronics Ltd
The SP 200 is a 3 digit LCD voltmeter with 9mm (0.36") digit height and LED backlighting. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into two 6-way SIL sockets and can be fitted into a panel via the fixing clip.
-
DPM 160 -
Lascar Electronics Ltd
The DPM 160 is a 4 digit LCD voltmeter with 12.5mm (0.5") digit height. It features 200mV and 2V d.c. full scale readings, auto-zero, auto-polarity and a set of annunciators. The meter plugs directly into a SIL socket or can be panel mounted using the snap-in bezel and window
-
2210 -
The Eastern Specialty Company
TESCO’s new Desktop Test Interface Station (Catalog No. 2210) provides metering professionals with exceptional testing flexibility. The Test Interface Station is ergonomically designed for meter technicians working in a lab or a desktop, yet still rugged for field use. The Test Interface Station includes a zero insertion force (ZIF) meter socket, voltage selection, form selection, open/closed-link selection and bi-directional cabling to power a load box/test kit & connect test standard potentials. When combined with a test kit/test standard and powered via 120 VAC, the Test Interface Station creates a single position, stand-alone, meter accuracy testing device for various socket based meters (both mechanical & solid-state).
-
8023 -
VECTOR Electronics and Technology, Inc.
3-hole solder pad for interconnecting multiple component leads. I/O area with square solder pads for connectors mounting. Circuit pattern etched onto both sides. Double sided with plated thru holes. Solder mount DIP sockets or IC devices with any lead spacing.