Showing results: 2971 - 2985 of 3380 items found.
-
COMBI521EV -
HT Italia Srl
COMBI521EV is the new HT instrument to perform verification and control of electric car charging stations (EVSE) safety according to IEC / EN 61851-1 and IEC / EN60364-7-722 standards. Being a combined verification instrument, COMBI521EV also carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
ViTec Co. Ltd
To ensure reliable operation of the measuring complex in the harsh conditions of ice tests, it is based on the industrial measuring platform NI CompactRIO, which provides mechanical strength and operation at negative temperatures.The system provides for operation both under the guidance of an operator with displaying the voltages removed from the ship's hull in the form of graphs on a computer screen connected to the strain gauge station via an Ethernet line, and in stand-alone mode, when the recording of a given duration is initiated by the station on pre-configured events: amplitude exceeding by one of channels, an external discrete signal or periodically at specified intervals.
-
MODEL PSMR -
Transducer Techniques, Inc
The PSM-R is a self contained AC power bridge excitation supply. This device consists of a low interwinding capacitance AC transformer and a high stability adjustable linear regulator designed specifically for driving transducer bridges. DC excitation is adjustable from 4 to 15 volts output and is capable of supplying 0 to 150 mA in output current. It features remote sensing to eliminate line drop errors and very low noise. It can also be used as a high quality voltage source or reference in many applications. AC input requirements are 105 to 125 VAC at 60 Hz.
-
40-592A-118 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines. Typical applications are in automotive and aerospace industries which involve safety or mission critical systems that have to behave predictably when cabling or sensor faults occur.
-
40-592A-014 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines. Typical applications are in automotive and aerospace industries which involve safety or mission critical systems that have to behave predictably when cabling or sensor faults occur.
-
ARC Technology Solutions
Whether you are testing RF LRU modules as a defense contractor, or implementing the next power supply tester for EV charge stations, ARC can create a custom, flexible automated end of line test solution for a variety of needs, with your budget in mind.Leverage our expertise with PXI mixed signal modular instruments, RF test capabilities and switching to complete your next solutions. Shorten your test development times, improve hardware and software standardization, and control your future test development costs by partnering with ARC on your next project.
-
C8000 -
Chroma Systems Solutions, Inc.
Power conversion testing is our core competency. Chroma’s engineering delivers cost-effective automated test system and software platforms to fit your Design Validation Testing (DVT) requirements in the lab or High Speed Functional Testing in the production line. Built into each system are Chroma’s years of expertise, precision instrumentation, pre-written test libraries, and local program management with global support. From power conversion to battery to electrical safety, our test systems will maximize your time, improve your validation process, and increase your throughput.
-
Chroma 16502 -
Chroma Systems Solutions, Inc.
With a basic accuracy of 0.05%, Chroma 16502 offers a 0.001mΩ ~1.9999MΩ wide measurement range. It provides measurement range with 4 1/2 digits resolution. The fast measurement time is 65 ms. It suits component evaluation on production line. Pulsed test current output mode is used to reduce thermal EMFs affection on milliohm measurement. DC test current output mode is used to fasten measurement speed for inductive DUT. Dry-circuit test current output mode is used to measure such contact resistances where the maximum open-circuit voltage must be limited to 20mV.
-
GVS7116 -
Hangzhou JiGao Electroacoustical Science and Technology Co.,Ltd
GVS7116C automatic frequency sweep signal generator is an instrument designed for detecting various electroacoustic components (Rattle & Buzz) and its dynamic test. It is suitable for use in the R & D department, quality control department and production line of manufacturers of speakers, headphones, receivers, buzzers, sirens, etc., as well as for the inspection of incoming materials in factories that manufacture various electroacoustic products. Such as audio factory, telephone factory, earphone factory, speaker factory, computer multimedia factory, etc. Standard sine wave, low distortion, best for listening to noise from speakers.
-
TAS7400 -
Advantest Corp.
The TAS7400 product line offers a series of low-cost, all-purpose spectroscopic systems that enable spectroscopic measurements using terahertz (THz) waves. The tools are capable of performing non-destructive analysis on a wide variety of sample types, making it applicable to a broad range of fields from life sciences to electronics, where precise chemical and material characterization is critical. The systems are ideal for settings ranging from basic research to product development, as well as for manufacturing and quality control, and employ easy-to-use spectroscopic methods that do not require specialized knowledge of THz wave generation or optics.
-
PXI-2200 Series -
ADLINK Technology Inc.
ADLINIK PXI-2204, PXI-2205, and PXI-2206 are high-density, high-performance multifunction PXI modules. These devices can sample up to 64 AI channels with various gain settings and scan sequences---making them ideal for high-density analog signals with various input ranges and sampling speeds. These devices also offer a differential mode for 32 AI channels to achieve maximum noise elimination. The PXI-2200 series also features analog and digital triggering, 2-CH 12-bit analog outputs with waveform generation capabilities, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timers/counters.
-
OVTT 24 -
Qualmark Corporation
The OVTT, OmniAxial Vibration Table Top, series introduced the first stand-alone, compact, repetitive-shock vibration system on the market and features Qualmark's patented six-degree-of freedom vibration technology. The OVTT24 system provides 77% more table surface area than the OVTT 18 which makes it an ideal tool for in-production-line, broadband spectrum vibration testing of product. It is also ideal for quick evaluation of field returns, repair verification and random vibration testing of multiple small products and can be configured for placement inside a thermal chamber for combined stress tests.
-
Tenney Environmental
Tenney Environmental offers a line of compact benchtop humidity and temperature test chambers that provide a small footprint and maximize workspace. These benchtop environmental chambers range from 1 to 5 cubic feet making them ideal for laboratories. In addition to laboratory applications, benchtop test chambers are commonly used for electronic, military, and pharmaceutical quality assurance and reliability testing, along with research testing and production processes. Even though Tenney benchtop environmental testing chambers take up minimal space they offer well sized interiors for product testing.
-
PeakTech Prüf- und Messtechnik GmbH
A loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
Lynx R Series -
Xenics
The Lynx R series, based on an in-house developed linear InGaAs detector, is a high-performance short-wave infrared (SWIR) camera providing high speed and quality line-scan imaging.The Lynx R cameras are able to image line rates up to 40 kHz, for demanding spectroscopy applications.The camera comes with an industry standard CameraLink or GigE Vision interface.Benefits & Features• High speed line-scan imaging up to 40 kHz (10 kHz for the 2048)• High resolution 1024/2048 Rectangular pixels option (12.5μm x 250μm)• CameraLink or GigE Vision interfacing