Showing results: 3076 - 3090 of 5219 items found.
-
LS6100 -
Lisun Electronics Inc.
Designed to measure the aging-life and color comparisons of 260pcs DIP LED. • 260 separate constant current supply • Aging functions: constant current, impact pulse, on-off mode • Range of forward voltage(VF): 5.0V • Range of forward current(IF): 1) constant current: 0-100.0mA 2) Impact pulse: 0-200.0mA • Range of impact pulse frequency: 10-9999Hz; Duty ratio: 1%-99% • Range of on-off circle: 0-9999H59M59S • Range of on-off times: 0-9999times • Range of aging time: 0-9999H59M59S
-
AudioJog Rack -
CableJoG Ltd
There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found. The LED's also show the possibility of high resistance or leakage connections.
-
925VST -
Sage Instruments
THE 925VST is a powerful handheld voice over packet (VoP)service qualification tool for field deployment and troubleshootingpersonnel who need a rapid and reliable installation tool.
-
CT-01 -
Laxtronics Instruments & Controls Pvt. Ltd
5 Kilo Volt AC, 30 Milli Ampere, Timer 0 To 100 Seconds, HV Prods, Start-Stop-Trip-Reset Using Single Switch On The Test Prods. Start Function Apply Test Voltage From 0 To Set Voltage Graduall
-
LX-221A+ -
Shenzhen Lian Xin Technology Co., Ltd.
·Meet UL, VDE, CSA, SAA, T-MARK, KS. IRAM, CCC and other countries’ standards .·Used to test single – ends ,double –ends ,three-ends power supply cords.·Auto and continuous test in COND,Insulation Resistance ,Leakage Current, Line-to-line Hi-pot(inside HV), Leaking copper(outside HV), relative length,·Auto test the fine and detective goods, tested qualified ones can be be ejected by ejector pin and marked , automatic cutting defective products, and alarmed with voice prompt and light,·Provide with RS 232 interfaces, can communicate with PC, easy to upgrade,·Provide personalized customization according to different requirements.
-
Tektyte Pty. Ltd.
The Log4 USB is a circuit measurement tool which both display accurate readings of voltage, current, and power while also simultaneously logging all measurement data to a MicroSD card and/or the free dedicated PC software. The Log4 USB device is specifically designed to measure the low positive voltages of USB connected equipment with high accuracy.
-
-
MODEL - KM 2030 -
Kusam Electrical Industries Limited
• Display : 3½ Digit LCD display.• Ground resistance measurements from 0 ~ 01Ω to 2000Ω with 0.01Ω resolution.• Earth Resistance : 20Ω / 200Ω / 2000Ω• Accuracy : 20Ω : ± (2% + 0.1Ω); 200Ω / 2000Ω : ± (2% + 3)• Earth Voltage : 0 ~ 30V• Accuracy : ± (3% + 5)• Resolution : 0.01Ω• Working LED Indicator.• Data Hold Function.
-
7500 -
Tokyo Electronics Trading Co., Ltd.
ESD test based on Human Body Model (HBM) and Machine Model (MM) is the most important reliability test among the Electro-static Discharge (ESD) test of the semiconductor device. Latch-up test, on the other hand, should not be omitted from the reliability test of the CMOS devices.
-
DBT125 -
Sterling Power USA
Battery load test. Depending on the size of the battery, this product adds a very high load to the battery (125 A). It enables the reading of battery condition by voltages and by its ability to maintain the load, thus determining levels of sulphation.
-
BK2019B -
BaKo Co., Ltd
With the BK2019B, you can test for open/short circuits, operating current and even vibration level. Because it has only one purpose, it is very easy to set up and use and it's so small it can fit into the average briefcase.
-
MG-III -
Chongqing Kailian Yongrun Industrial Co.,Ltd.
It is designed to determine the dissipation factor (Tan Delta), capacitance and resistance of transformer oil and other liquids. Relative dielectric constant and volume resistivity are calculated automatically and displayed.
-
ATE Service Corp
Place inner layer GND plane all over. Impedance control of signal line and crosstalk prevention, etc. contribute to improvement of characteristics in various ways.
-
26200 -
Lisle Corp.
Just clip lead to one end of wire in question. Probe other end of wire. If bulb lights up, there is continuity. If bulb fails to light the circuit is open. Not to be used on live circuits or computer sensor feed circuits.
-
CBT1 -
Hanatek Instruments
The instrument measures crease folding force at 90°, board stiffness at 15° and requires no external software for operation. It automatically calculates the crease to board stiffness ratio for instant indication as to whether the material will run correctly on a high speed packaging machine.