Showing results: 5116 - 5130 of 5239 items found.
-
JEMIO -
StarTest
The JTAG External Modules JEMIO™ for Cluster test are intended to provide test access to off-board signals that otherwise could not be accessed by a JTAG test system. For many designs, Boundary-Scan has adequate access to on-board signals, but signals that go off the board often cannot be tested by a JTAG tester. By adding JTAG access to these off-board signals, JEMIO™ modules can increase the board's JTAG test coverage, possibly reducing the need for implementing another test method or for developing alternative tests to reach the required level of test coverage.
-
PeakTech Prüf- und Messtechnik GmbH
A loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
SCR ELEKTRONIKS
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
GWT A2 -
SCR ELEKTRONIKS
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
Static Solutions Inc.
Measures resistivity RTT, RTV, and RTG 103-1012 ohms/sq., ohms, ohm-cmRelative humidity 10% 90% RHTemperature 32oF 100oFDigital display: easy to interpretNIST calibration includedIncludes chair probe to measure smocks, earth ground, chairs, and resistance probes: $400 value for freeResistivity probe built in the bottom of meterProduct conforms to the ESD S.20.20 spec standardsCE mark includedThe kit includes, two (5) lb probes, coil cords, hard carrying case, battery, 110v or 220v adaptor, garment clips, chair probe, and ground circuit tester
-
CMPHEAD50 -
Rohde & Schwarz GmbH & Co. KG
The R&S®CMPHEAD50 is the only remote radio head supporting bi-directional testing at five mmWave frequency bands with one hardware set and EVM booster ports. It extends the R&S®CMP200 radio communication tester to frequency range 2 (FR2/ FR2-1). The improved performance ensures optimum accuracy for testing next generation FR2 RF designs – from early development to final certification and regulatory compliance. Test with confidence and ensured RF performance with the latest state-of-the-art measurement solution from Rohde&Schwarz.
-
TPM-50A -
ShinewayTech
ShinewayTech@ TPM-50A Terminal Power meter can test (1) Average power range: -40 dBm~+20 dBm；(3) Modulation bandwidth: 5MHz；(3) Continuous signal and burst signal test. Highly accurate power measurement CW and digital modulated signal (For example: GSM/EDGE, CDMA/EV-DO, WCDMA/HSDPA, WiMAX, and TD-SCDMA). It is very important to test that if the transmitter is at a specified level or not. For example, the tester needs to test the output power of base station. Because the lower output power produces the larger coverage area to cause call interruption.
-
NuVant Systems, Inc.
Our line of HEV / EV Battery Equipment combines sophisticated electronics, advanced technology, and user-friendly operation. The EVc Battery Reconditioner processes all types of nickel metal hydride HEV batteries. Worldwide, the EVc has proven to be a neccesary workhorse for any hybrid auto shop or garage. The EVd Power Tester monitors individual module voltages during high power battery discharge. The EVd also features a "smart" charger that performs complex CCCV charging. We are currently developing technology to process and rebalance the Li-ion batteries for electric vehicles.
-
mOByDic1700 -
Ozen Elektronik Inc.
The J1939 multiple ECU simulator provides a professional OBD development platform which allow the user to test the OBD functionality on the table. Simulates a Truck ECU . Using 5 potensiometer , 5 live data can be changed and some fixed PNG values are provided. Pressing DTC bouton the trouble codes are generated and the MIL LED is ON. DM11 commands clear the DTCs and the MIL LED. Connection to the tester is provided via a J1962 female OBD port . it needs an external 24 V power supply . More information you can get from the corresponding chipset datasheet.
-
190 -
Electronic Specialties Inc.
Relay Buddy is a quick go / no-go tester for the most common automotive relays. It provides you with an indication of the general health and functioning of the relay switch contacts and coil. Relay Buddy will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.
-
Megger Group Ltd.
Megger Baker Instruments designs and manufactures electric motor test systems for original equipment manufacturers (OEMs) that help ensure their motors, generators and coils meet or exceed the quality expectations OEMs set with their customers. Baker motor quality control (QC) systems include the Baker WinAST automated stator tester, the Baker HV WinAST and the Baker WinTATS traction armature test system. Each incorporates the most effective electric motor test processes into a single automated instrument and can be customized to meet the specific testing needs of a given manufacturer.
-
Keysight Technologies
Accurate DC/CV (and RF) statistical modeling of semiconductor devices requires collecting a significant amount of measured data from different wafers across several temperatures. Keysight Technologies recommends IC-CAP WaferPro as a turn-key DC/CV and RF automated characterization solution to help modeling and device engineers achieve more efficient on-wafer measurements across temperature. This new breakthrough solution is based on IC-CAP modeling software and efficiently controls DC/CV analyzers, network analyzers, probers, switching matrixes, and temperature chucks, as well as the powerful 407x and 408x Series of Keysight parametric testers.
-
MTS-207 -
Terotest Systems Ltd.
The MTS-207 is a state-of-the-art portable PXI platform for field testing and data acquisition systems. Its proven architecture has been deployed worldwide on multiple programs including the MTS-206 Maverick Missile system flight line tester. The MTS-209 Common Armament Test Set, the AN/TSM-205B Hellfire System test Set, and many more. It combines the capabilities of the versatile and powerful PXI architecture in a compact, ultra-rugged, flight-line qualified enclosure. The MTS-207 is ideal for test and data acquisition applications requiring operation under harsh environmental conditions including flight-line, back-shop, or airborne applications.
-
MTS-207 -
Marvin Test Solutions, Inc.
The MTS-207 is a state-of-the-art portable PXI platform for field testing and data acquisition systems. Its proven architecture has been deployed worldwide on multiple programs including the MTS-206 Maverick Missile system flight line tester, the MTS-209 Common Armament Test Set, the AN/TSM-205B Hellfire System test Set, and many more. It combines the capabilities of the versatile and powerful PXI architecture in a compact, ultra-rugged, flightline qualified enclosure. The MTS-207 is ideal for test and data acquisition applications requiring operation under harsh environmental conditions including flightline, back-shop, or airborne applications.
-
SONODUR Product Family -
Foerster Instruments, Incorporated
The non-destructive UCI test method (Ultrasonic Contact Impedance) as well as the Leeb test method enable fast and mobile measurement as a supplement to the classical hardness test. Due to the compact measuring probes and sensors of the SONO series, the devices can also be used in difficult test positions and with complex component geometries. Fields of application are e.g. incoming goods inspection, mix-up testing, production control, quality assurance, weld seam testing, cut edge testing, maintenance on installed components as well as the replacement of dynamic hardness testers for small material thicknesses (below 50 mm, e.g. boilers, tubes).
