Showing results: 106 - 120 of 821 items found.
-
KM 6300 -
Kusam Electrical Industries Limited
Measurement of current, voltage, active, reactive and apparent power, Power factor, line frequency, energy, harmonic and Maximum Demand.
-
UBi -
Creative Lighting
Every UBi can create up to 6 branches of a DALI line. Simply put a DALI line into one of the 2-way pluggable terminals, and then use any combination of the 5 remaining terminal pairs to route your cable anyway you like. Or, if you want the UBi to be a power supply, simply power a UBi Power with 24VDC and it will power your DALI line with 21.9VDC 245mA and still give you 5 DALI connections – one for your DALI controller and four to branch however you like.
-
HSA4200 (With SNMP) -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4200 series is a line EDFA designed specifically for single wavelength optic transmission system. It is installed in the middle of the transmission line, replacing the traditional relay station, to compensate the optical power loss in the line and extend the signal transmission distance.
-
Ametek Power Instruments
RF hybrids are used for combining multiple power line carrier (PLC) TX/RX units together onto one cable without causing interference between transmitters and receivers. They are also used for splitting PLC signals to go to two or three phases of a power line.
-
Hilkar
Iron core Shunt Reactors act as an absorber of reactive power to increase energy efficiency of the power system. Shunt Reactors are used in order to compensate capacitive reactive power generated by long and lightly loaded transmission lines as well as underground cables, thus allowing the flow of more active power through the system and avoiding over voltages. Shunt Reactors can be directly connected to the power line or to a tertiary winding of a three-winding power or distribution transformer.
-
-
Dynamic Engineering
The Stand Alone Relay accepts a regular PC style power connector that powers two relays. Upon power failure, the relays disengage the two ethernet lines so as to not interrupt communication on the ethernet lines. A CPLD allows for pass through and bypass of Ethernet signals. 10/100 Ethernet compatible. The CPLD is controlled via user input.
-
Coaxial Dynamics
Coaxial Dynamics "Standard" line of RF Power Sensors provide DC currents proportional to the forward and reflected power flowing through the line. All models are designed to drive a 30A, 1400-Ohm meter, or provide approximately 100 millivolts across a 5K load.
-
Schweitzer Engineering Laboratories, Inc.
Overhead faulted circuit indicators include easy-to-spot displays to help direct line crews to the faulted line sections—enabling faster restoration of power and improved customer uptime.
-
1EA065 -
Le-tehnika, d.o.o.
ISDN line checker shows the correctness of your ISDN So bus line connections. Indication of the problem is presented with 4 LED (combination of them shows different states and working conditions of the ISDN So bus). The tester uses Phantom power - no need for additional power supplay.
-
WT2080-OK -
Lisun Electronics Inc.
WT2080-OK LED Power Driver on line Tester is according to GB/T 24825-2009 and IEC 62384: 2006. It suitable for LED Driver production line testing quick test (0.1s finish the testing). The WT2080-OK can test 1pc LED Driver at one time in the production line.
-
TW-82P -
Aegis Pty. Ltd.
Digital Line Tracer now with Passive Power Detection setting a NEW standard in High Frequency Line Tracing. The TW-82P Digital Line Tracer inlcudes a rugged contruction and compliant with IP65 standard. The casing is impact resistant and weatherproof ensuring you're ready for any conditions.
-
TW82P -
Aegis Pty. Ltd.
Digital Line Tracer now with Passive Power Detection setting a NEW standard in High Frequency Line Tracing. The TW-82P Digital Line Tracer inlcudes a rugged contruction and compliant with IP65 standard. The casing is impact resistant and weatherproof ensuring you're ready for any conditions.
-
INS Series -
Noise Laboratory Co.,Ltd.
A simulator to reproduce fast rise-up noises which are generated when switching ON / OFF electric current on the inductive load. It can be used for performance evaluation of electronic equipment upon reproduction of line noises which are intruded to the power supply lines or induced noises onto the telecommunication lines.
-
Gentec Electro Optics, Inc.
We have the most complete high power product line on the market, with solutions for powers as high as 25 000 W, more upon request.