Filter Results By:
Products
Applications
Manufacturers
Bare Board
is a printed wire board only.
See Also: Bare Board Probes, Bare Board Testers, Bare board Fixtures
- CAMI Research Inc. (CableEye®)
product
2100Vdc Screw Terminal Connector Board | Cable & Harness Tester
CB29H
CAMI Research Inc. (CableEye®)
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination. Each contains four 16-pole screw terminal blocks that will accept bare wires from 12- to 30-gauge in size. The metal jaws firmly grip an inserted wire without damaging or distorting the end, and the space between each terminal block may be used as a wire channel to guide wires neatly to the side. For each channel, a pair of holes is provided through which wire ties may be inserted to hold the wire bundles in place.
-
product
Bare Board Tester
1232
High-Precision Batch Fixture-Type Testing System that Support Boards with Embedded Passive and Active Devices. The 1232 is a bare board tester that utilizes the full range of Hioki’s in-circuit testing technologies to deliver LSI reliability testing, complex component separation testing, high continuity and insulation testing, and more. (Double-sided alignment) Testable board dimensions: 50 × 50 to 330 × 330 mm (including clamp area) • Support for build-up boards that require resistance guarantees.
-
product
Bare Board Tester
Rapid 270
The Rapid 270 (automatic Bare Bord Tester) combines the versatility and reduced footprint of a vertical system with the automation featuring the testers with horizontal architecture.
-
product
Bare Board Electrical Testing
ProbeMaster
ProbeMaster is the complete software solution to your shops needs in bare board electrical testing. ProbeMaster is PentaLogixs top-of-the-line software package that combines all of the power of the PentaLogix CAM and Fixturing packages with support for moving probe, Netlist Comparison and other robust features.
-
product
BARE BOARD TEST PROBES
Probe Technical DataMechanicalMINIMUM CENTERS: .100 (2.54)FULL TRAVEL: .160 (4.06)WORKING TRAVEL: .107 (2.72)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current60 18 mOHMS mean63 60 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper60 24 Kt gold plated over nickel63 24 Kt gold plated over nickelBARREL: Nickel silver60 24 Kt gold plated ID and OD over nickel63 No FinishSPRING: Music Wire, 24 Kt gold platedover nickel
-
product
PCBA & Bare Board Cleanliness Tester
Zero-Ion G3
For two decades, thousands of electronics assemblers have relied on the Zero-Ion cleanliness testing to verify the cleanliness of post-reflow printed circuit assemblies and bare boards. Over time, as PCB assemblies have become more complex and more densely populated with surface mount components, and as vigorous quality standards such as ISO, TQM and Six Sigma have become commonplace, the ability to meet—and confirm—cleanliness levels has grown in importance. The Zero-Ion ROSE tester has kept pace with customer requirements, and the Zero-Ion G3 is the most advanced Zero-Ion ever designed, capable of testing assemblies reflowed with any solder paste, including no clean—yet its also one of the most affordable cleanliness testers on the market as well, with performance and ease of use second to none.
-
product
Special Assemblies Bare Board For Prototypes
YAVPROCUS
This module has a shape and size that provide a simple way to create custom applications either directly inside the test fixtures or inside the 19” chassis 7300 30. This module simplifies the work of the test engineer when talking about documentation or additional reproduction of spares or prototypes.
-
product
Automated Bare Board Tester with Built-In Camera
QTOUCH2404C
Qmax Test Technologies Pvt. Ltd.
Qtouch2404C – Automated Bare Board Tester with in-built camera is designed to make automatic image capturing and probing of bare PCBs. It is designed to move on X,Y,Z directions making it possible to probe every test point. Flying Probe Tester is designed for testing high density fine pitched Single Sided / Double Sided and Multilayer PCBs for continuity and isolation using moving probes fixture –less technology.
-
product
LUTHER & MAELZER BARE BOARD TEST PINS
SERIES LMP 78
Materials and Finishes MATERIAL: Heat treated beryllium copper FINISH: 24 Kt gold plate over hard electroless nickel
-
product
LUTHER & MAELZER BARE BOARD TEST PINS
SERIES LMP VZ
Materials and Finishes MATERIAL: Heat treated beryllium copper and music wireFINISH: 24 Kt gold plate over hard electroless nickel
-
product
Hign Speed Bare Board Test System By Non-Contact Test Technologies
SX-750SUPERⅣ
Suitable for a wide range of applications. Can be connected to a wide range of machines: from hand press to reel mechanism and in-line mechanism. We offer docking with our customers own machines. Compact main tester simplifies integration via installation inside a mechanism. If requested, we will perform a study to decide which functions should be added.
-
product
NON-CONTACT TEST COMPATIBLE Ultra High Speed Bare Board Tester System(ALL-IN-ONE UNIT)
SX-750SUPERⅣC
All-in-one Compact Size TesterAll-in-One type Tester, with built-in PC in the Tester main unitImproved operability with a 10.4" Touch PanelAll the operation screens are optimized for touch-pannel operation.
-
product
PXI Express Optical FPGA Board
HSS-8324
The Conduant HSS-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface. The PXIe interface provides a theoretical maximum throughput of 8GB/s (simultaneous in and out).
-
product
FPGA Boards
Take advantage of FPGA cards built on open standards and with a high degree of configurability in order to address a wide range of applications - without the expense and extensive development time of custom in-house developments.
-
product
FPGA Board
VP889
The VP889 is a high-performance FPGA processing board featuring Xilinx® Virtex Ultrascale+™ and Zynq® Ultrascale+™ technology.
-
product
FPGA Processing Board
VP880 / VP881
The VP880 / VP881 is a high-performance FPGA processing board featuring Xilinx® Ultrascale™ and Zynq® Ultrascale+™ technology. It is designed for the most demanding, mission critical military/defense applications such as electronic warfare / DRFM, radar/sonar image processing, satellite communications systems, multichannel digital transmission/reception and advanced digital beamforming.
-
product
Qseven® Reference Carrier Board
Q7-BASE
Qseven is a Computer-on-Module (COM) standard for small sized and highly integrated systems adopted by SGET. The Qseven concept is an off-the-shelf, multi-vendor, Computer-on-Module that integrates all the core components of a common PC and is mounted onto an application specific carrier board. Qseven modules have a standardized form factor of 70 mm x 70 mm or 40 mm x 70 mm and have specified pinouts based on the high-speed MXM connector, regardless of the vendor. The Qseven module provides the functional requirements for an embedded application, which include, but are not limited to, graphics, audio, mass storage, network and multiple USB ports. A single ruggedized 230 pin MXM connector provides the carrier board interface to carry all the I/O signals to and from the Qseven module. This MXM connector is a well-known and proven high-speed signal interface connector that is commonly used for -PCI Express graphics cards in notebooks.
-
product
Analog-to-Digital Converter Board
VME-3125A
Isolated Scanning 12-bit 32-Channel Analog-to-Digital Converter Board (6U) with Built-in-Test (BIT)
-
product
SMARC 2.1 Reference Carrier Board with M.2 Extension
I-Pi SMARC Plus
The I-Pi SMARC Plus is small (110mm x 110mm) SMARC reference carrier board based on SGeT SMARC (Smart Mobility ARChitecture) 2.1 hardware specification. Together with the SMARC short size module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
Quad QSFP28/QSFP+ FMC+ Module
iWave’s QSFP28/QSFP+ 2×1 Stacked FMC+ HSPC Module is designed to meet VITA 57.4 FMC+ Standard. This FMC+ Module is supported by two stacked QSFP28/QSFP+ ports(Upto400G) with 4-Bit Silicon Labs programmable clock synthesizer (default = 156.25Mhz). A flexible reference clock for on the QSFP28/QSFP+ 2×1 Stacked FMC+ Module is fully programmable over the 0.16 to 710 MHz range through I2C. Each QSFP28/QSFP+ ports are directly connected to four multi-gigabit serial transceivers banks of Vita 57.4 compliant carrier Board.
-
product
Cyclone V based 6U cPCI COTS Module
iWave’s Cyclone V based 6U cPCI Card is a rugged standalone module complaint with 6U size CPCI PICMG 2.0 Rev 3.0 backplane, aimed for the high-speed data, video processing, and display applications. The card offer speed up to 512MB/s of DMA transfer and up to a 6 channels of transceiver interfaces capable of operating up to 6 Gbps, SFP, Built-in health monitoring circuits, DVI Input, and Output Interfaces
-
product
FMC Add-On Cards
iWave’s FPGA-IP Evaluation Add-On FMC Card is designed to meet ANSI/VITA 57.1 FMC Standard. The card supports both High-Pin Count (HPC) & Low-Pin Count (LPC) connector and can be used in an air-cooled environment. FPGA-IP Evaluation Add-On Card can be interfaced with most of the FPGA development kits available in the market. This card also helps to evaluate iWave’s proprietary FPGA Intellectual Property (IP) Cores.
-
product
PCI-8 AE Board
The PCI-8 is an 8-channel, PCI-based AE system on a board. Its 8 high-speed AE channels offer simultaneous AE data acquisition, waveform processing and data transfer. The board’s standard PCI form factor enables installation in standard PCs, as well as in any of Physical Acoustics’ specialized AE system chassis, while the PCI bus enables AE data transfer at speeds of up to 132 Mb/s, at a frequency range of 1 kHz to 400 kHz.
-
product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
PCI Three-Axis Laser Board
N1231A
The Keysight N1231A PCI Three-Axis Laser Board is a register based PCI bus board that implements three axes of laser measurement for position monitoring and closed-loop servo control. The hardware outputs, optimized for connection to a DeltaTau PMAC servo control system, provide parallel digital position data at rates up to 4MHz. The same position data along with velocity data is available over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
3U CompactPCI® Single 64-bit PMC Slot Carrier Board
cPCI-8301
*PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus*Supports one single-size 32,64-bit/33,66 MHz PMC site in 4HP width*Universal V(I/O) decided by backplane*Comprehensive EMC shielding
-
product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
*Supports 32bit, 33/66MHz CompactPCI® bus*One SIM card socket*One Mini PCI and one Mini PCIe socket*PICMG® 2.0 R3.0 compliant
-
product
34945EXT Distribution Board, For Two 87222, L7222C Transfer Switches And Six N181x SPDT Switches
Y1154A
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
product
Computer On Module
ITX-M-CC452-T10
The ITX-M-CC452-T10 is an industrial Mini-ITX small form factor Type 10 reference carrier board designed to fully test WINSYSTEMS’ COMeT10-3900 COM Express Type 10 Mini module. The carrier board adheres to the PICMG COM Express specifications providing compatibility with other COM Express mini type 10 modules.
-
product
COM Express Type 6 evaluation carrier board
ATX-M-CC462-T6
The ATX-M-CC462-T6 is a fully featured COM Express Type 6 evaluation carrier board designed for use with the WINSYSTEMS Intel® Tiger Lake UP3 COM Express and other COM Express Type 6 modules.
-
product
M/MA Module Carrier
VX405C
The VX405C carrier provides the mechanical and electrical interfaces between the VXIbus and up to six (6) VITA 12-1996 standard M/MA-Modules. The carrier provides VXI register configuration and access to the M/MA-Module I/O space and memory (if present). Each M/MA-Module is controlled separately and appears as a different logical address in the VXI environment. Over 100 M/MA-Modules are available that can provide custom interfacing to the unit under test (UUT). Up to six (6) unique interfaces may be provided in a single VXI slot.
