Showing results: 1501 - 1515 of 1689 items found.
-
KLA-Tencor Corp
KLA’s advanced process control and process enabling solutions support integrated circuit manufacturing. Using KLA’s comprehensive portfolio of defect inspection, review, metrology, patterning simulation, in situ process monitoring and data analytics systems, IC manufacturers can manage yield and reliability throughout the chip fabrication process - from research and development to final volume production. SPTS provides deposition process solutions for insulating materials and conducting metals that cover a range of chip manufacturing process steps. IC manufacturers use KLA's array of products and solutions to help accelerate their development and production ramp cycles, to achieve higher semiconductor die yield and improved IC quality, and to improve overall profitability in the IC manufacturing process.
-
Series KA/LA -
Teledyne Defense Electronics Relays & Coax Switch
Series KA/LA solid-state relays are designed for use in AC power switching applications where safety and reliability are primary concerns. They are ideal for resistive and reactive loads with power factors as low as 0.2. Inverse parallel SCRs are configured for zero-voltage turn on. The relays are available with thermal protection and thermal trip status.MSL 1 Available options include:KA58HF 2Arms, 250Vrms Load; 3.8-32Vdc bias voltage, 250µA CMOS Control; includes thermal protection & thermal trip statusLA00HL 2Arms (7.5Arms with heat sink), 250Vrms Load; 3.8-32Vdc bias voltage, 250µA CMOS Control; LA58HL 2Arms (7.5Arms with heat sink), 250Vrms Load; 3.8-32Vdc bias voltage, 250µA CMOS Control; includes thermal protection & thermal trip status
-
NI
PXI Signal Insertion Switch Modules, also known as fault insertion units (FIUs), provide a set of feedthrough channels, which make the switch transparent to the system when closed. You can open or short these channels to one of two fault buses, allowing you to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI Signal Insertion Switch Module can validate the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs). You can also use the FIU models for hardware-in-the-loop (HIL) applications and electronic reliability tests.
-
ADTS-2000 -
TestVonics, Inc.
TestVonics ADTS-2000 Test Set is a portable, high precision, dual channel air data pitot static test system. This tester is designed to calibrate, test and troubleshoot air data instrumentation and aircraft pitot-static systems. The ADTS-2000 meets all requirements of the KTS-2000 , P/N: 18910920000, P/N: 18910920001, P/N: 18910920002, or having NSN: 4920-01-588-4428 and NSN: 4920-01-554-4549 . The test set has been designed with functional and reliability features highly suited to withstand the harsh environmental and demanding conditions of the flight line environment. The test set is designed for testing a wide range of commercial and military aircraft, both rotary and fixed wing. The ADTS-2000 accuracy complies with standards for RVSM and is designed to replace the TTU-205 test set.
-
PX3 Series -
Honeywell Sensing & Control
Honeywell is pleased to announce its efficient, affordable and durable PX3 Series Heavy Duty Pressure Transducers, designed primarily for system pressure monitoring in HVAC, refrigeration, air compressor, pump and valve systems. Key features and benefits include: Delivers high efficiency: Proven, 1.0% FSS tight Total Error Band accuracy promotes system efficiency and lower energy costs. Great customer value: Economical choice for design/implementation; extremely flexible with multiple configuration possibilities with the right combination of features and broad media compatibility. Durability promotes system uptime: For enhanced performance in tough environments to support overall system quality, reliability and warranty. Fast availability: Short lead times on samples and production parts.
-
Wewon Environmental Chambers Co, Ltd.
The environmental chamber for conditioning of samples prior to testing, It also can be used for a variety of materials of high – low temperature alternating test. The test for temperature, humidity, time can be programmed. Provides conditions of temperature from -70 degree to +180 degree and of humidity form 10% to 98%.environmental chamber ● The ideal simulation environmental chamber for all heat and cold testing between -70 ºC and 180 ºC temperature range.● Well suited for reliability testing based on current test standard in the temperature range of -70 °C to 180 °C & 10% to 98% RH.● This design SUS environmental chamber meet all requirements for extreme testing and low temperature alternating climate profiles from -70 °C -180 °C with humidity
-
40-195-001 -
Pickering Interfaces Ltd.
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
40-195-101 -
Pickering Interfaces Ltd.
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
GT00YA00ZX -
GAO Tek Inc.
The GAOTek Portable H/L Voltage Clamp Current Leaker measures high voltage current with a 12.5 in (32 cm) insulating rod, adopting the latest CT technology and integrating mask digital technology. This instrument provides high precision, reliability, and stability with its integrated design between transducer clamp and domain. This leaker can be used to measure any wire with or without the insulation layer where the voltage is below 10 kV. The insulating rod is portable, moisture resistant, heat resistant, shock resistant, and insulating. It provides additional functionalities such as online current testing, peak and data holding, data storage, detection of high and low current in primary and secondary circuits separately, and provision of suitable calculations to conclude change in high and low pressure.
-
T5851 -
Advantest Corp.
Advantest Corporation has introduced the T5851 system, designed to provide a cost-effective test solution for high-performance universal flash storage (UFS) devices and PCIe BGA solid-state drives (SSDs) memory ICs in high demand by makers of low-power, mobile applications such as smart phones, tablets and ultra-portable laptops. The flexible T5851 tester is available in both production and engineering models. This allows the system to be used for reliability and qualification testing as well as test-program development or, when equipped with an automated component handler such as Advantest''''s M6242, high-volume production. As a fully integrated, system-level test solution, the T5851 provides multi-protocol support in one tool while its tester-per-DUT architecture and proprietary hardware accelerator allow it to achieve industry-leading test times.
-
A8a -
atg Luther & Maelzer
The A8a test system provides the flexibility of flying probe testers while delivering high throughput testing for bare board printed circuit boards (PCBs). The target market for the A8a is the electrical test of tablet and PC motherboards and high density interconnect (HDI) products for smart phones. The A8a is designed for high productivity, reliability and test accuracy. To achieve high throughput the key feature of the A8a is a new dual shuttle system, which reduces the product exchange time to zero seconds in automation mode. In combination with the fast test speed of up to 140 measurements/second the A8a will give customers a competitive test solution for batches up to 5000 boards. A typical cycle time of a 4-up smart phone board is about 2 minutes.
-
National Technical Systems
NTS is the exclusive provider of HATS2™testing services in North America. Thermal shock testing has long been the accepted method to check robustness and reliability of plated-through holes and solder joint connections. Historically, thermal shock testing has been performed utilizing either dual chamber air-to-air systems or liquid-to-liquid systems. Both of these methods offer significant disadvantages in cost, time, and the fact that the samples must be transported between the hot and cold environments. Transportation of the samples between the temperature environments makes monitoring the resistance of the samples difficult and inaccurate due to the length and quantity of wires. The infrequent monitoring typically associated with traditional thermal shock methods also makes detection of “glitch” conditions marginal at best.
-
SNAKEHEAD -
ADVINT, LLC
The Snakehead platform employs aNI CompactRIO (cRIO) system consisting of an embedded controller, chassis, and NI C Series I/O modules.Snakehead systems are not dependent on a separate host computer. They offer both Ethernet, and Wi-Fi connectivity to powerful real-time controller with a user-upgradable backplane that includes a high performance field-programmable gate array (FPGA). Snakehead provides stand-alone embedded execution for deterministic LabVIEW Real-Time applications. These units are designed for ruggedness, reliability, and low power consumption. The heart of Snakehead systems is the reconfigurable I/O (RIO) FPGA core. The RIO core has an individual connection to each I/O module and is programmed using easy to use elemental I/O functions to read or write signal information from each module
-
B-1027 -
ROSS ENGINEERING CORPORATION
Ross Engineering Corporation’s High Voltage Calibration Lab provides high accuracy capability for conducting tough reliability tests on all our high voltage devices. In this facility we test and calibrate HV Relays, HV Dividers, HV Probes, Spark Gaps, our Fiber Optic Systems, and HV Digital Voltmeters up to 450kV. We provide our own in house test lab to ensure Ross products meet or exceed required safety standards as well as our own high standards of dependability, long life and quality. Our technicians use test equipment calibrated by or traceable to National Institute of Standards and Technology or other national metrology institute to provide the highest in testing accuracy.
-
Elbit Systems of America®
Elbit Systems of America is the industry leader in video, audio, and data recorder's for fixed and rotary platforms. Our compact Digital Video Recorder (DVR) enables recording video and audio channels on a solid state memory cartridge. Based on commercial off-the-shelf components, the DVR complies with stringent airborne data recording and mission debriefing requirements. Each DVR’s advanced design has no moving parts assuring high reliability in all conditions. With built-in growth potential, it is configurable from one to four video channels and can accommodate additional communications. The unit operates as a stand-alone system or integrates with existing systems and upgrade programs. Elbit Systems of America provides advanced solutions for the following fixed-winged and rotary platforms:
