Showing results: 241 - 255 of 775 items found.
-
AOSense
Rack-mount microwave atomic clock using laser-cooled 87Rb atoms. Production unit target specifications: Allan deviation 2×10-12 @ 1 s, 2×10-14 @ 104 s; flicker floor 1×10-14; absolute accuracy < 1×10-13.
-
Dynamic Engineering
The parallel Input and Output channels are highly programmable and fully independent. The standard interface offers Data, Clock and Strobe. The 32 RS485 channels are programmable as input or output allowing for a variety of implementations. The programmable output rates and RS422/485 compatability will interface to a multitude of systems.
-
CPCI-100A-BP -
Abaco Systems Inc
The CPCI-100A-BP 2-slot IndustryPack carrier for 3U CPCI is available with back-panel I/O via the CPCI J2 connector. The carrier provides an 8 MHz IndustryPack clock for each slot. The standard 8 MB memory space is available for each IndustryPack site.
-
ST-2 -
Rinch Industrial Co.,Limited
In / out temperature measurement. Clock function display. Super-thin design. Measurement range: -50℃∽+70℃Distinguish: >-20℃ is 0.1℃ ≤-20℃ is 1.0℃Accuracy:±1℃ Power: DC1.5V, battery LR44Product size: 56.5×37.8×11.3mm Screen size: 46.7×21.2mm
-
Pulse Instruments
Our CompactPCI series mainframes are industry-standard, open-architecture chassis with enhancements to support Pulse Instruments' clock driver and DC bias cards. The enhancements are transparent to the CompactPCI specification, and 3rd-party cards CompactPCI/PXI cards can be used in our mainframes without hardware or software modification*.
-
MSHD-02 -
Master Co. LTD
MSHD-02 distribute inputted component signal to the two (2) output channels via RCA connectors without diminuation & distortion. It takes High Bandwidth Video Distributor IC which is support the highest component resolution up to 1920X1080P & Dot Clock 148.5MHz.
-
Furaxa, Inc.
*Differential output - can also provide two separate single ended complementary outputs. * Pulse height of up to +4V peak into 50 ohms, on positive output * Pulse height of up to -4V peak into 50 ohms, on negative output * Rise time < 80pS, FWHM of approximately 120pS * Produces pulse on both edges of input clock, thereby doubling frequency. * Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz. * Usable energy to >10GHz. * Can drive any load, including short, without damage. * Power Requirements: -12V @ 120mA and +24V @ 80mA
-
COMBGEN6DIFF -
Ultraview Corporation
*Differential output - can also provide two separate single ended complementary outputs.*Pulse height of up to +4V peak into 50 ohms, on positive output*Pulse height of up to -4V peak into 50 ohms, on negative output*Rise time < 80pS, FWHM of approximately 120pS*Produces pulse on both edges of input clock, thereby doubling frequency.*Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz.*Usable energy to >10GHz.*Can drive any load, including short, without damage.*Power Requirements: -12V @ 120mA and +24V @ 80mA
-
Furaxa, Inc.
*Differential output - can also provide single ended outputs, one with positive going pulse, the second with negative going pulse. * Pulse height adjustable +1 to +5V peak into 50 ohms, on positive output, with concurrent -1 to -5V peak on negative output * Produces differential pulse on positive edge of input clock * Input clock may be 20-100MHz sinewave or 0.5-100MHz square wave, producing comb to 4GHz. Usable energy to >10GHz. * Differential outputs are designed to drive matched 50 ohm loads, but can drive any load, including short, without damage. Has integral fan. * Power Requirements: -12V @ 120mA and +18V @ 90mA.
-
U4206A -
Keysight Technologies
The U4206A is a direct-connect probe/cable with a standard soft touch pro connector at one end that routes to four 160-pin connectors that plug into the front panel connectors of a U4164A logic analyzer module. The U4206A is designed to be used with either the quad state mode or ¼ channel 10 GHz timing mode of the U4164A logic analyzer module. For use in quad state mode only, the U4206A includes two flying leads to connect additional clock qualifier signals into the clock inputs on Pods 3 and 7. Please refer to the U4164A installation guide for specific details on the operation of the U4164A quad sample state or ¼ channel 10 GHz timing modes of operation.
-
KT305 -
Ketai instrument (kunshan) Ltd.
Display: 29mm high LCD display.C/F temperature display; clock and date display.Hourly hour and daily alarm function.MAX/MIN temperature and humidity memory function.Storage environment: temperature -20 C~60 C, relative humidity <80% .Battery: One 1.5V AAA battery.
-
VCH-002 -
VREMYA-CH JS Company
The secondary master oscillator (VZG) is designed to operate in a digital communication network as a synchronization equipment of the second level of the hierarchy. Its task is to track in phase one or more clock signals coming through the network from the synchronization equipment of the highest or equivalent level of the hierarchy.
-
FMC168 -
Abaco Systems Inc
The FMC168 is a digitizer FMC featuring eight ADC channels with 16-bit resolution and 250Msps sampling rate per channel.With a flexible clock generation and distribution scheme, the FMC168 allows control of sampling frequency and analog input gain through serial communication with a carrier card.
-
PXI(e)530x -
VX Instruments GmbH
Up to 6.6 MS/s with 7 Bit pattern widthUp to 2 independent modules with 4 simultaneously working channelsBased on VX Instruments FlexCPP for easy custom designHighly configurable trigger engineMultiple instrument and channel synchronization possibilitiesIndependent sample clock input for every channel
-
XMC-FPD-xxx -
ALPHI Technology Corporation
XMC Bus VITA 42• 3.3V I/O, 5V tolerant businterfaces• Local Bus Clock rates at66MHz• Compliant PCIeSpecification, r1.0a x1• Direct slave data transfers• DMA Capability• Up to 160Mb/s Transfer• DMA Transfer per Fifo Level