Showing results: 91 - 105 of 275 items found.
-
PU 182.1 -
Metra Blansko a.s.
The instrument is primarily intended for measurement of the insulation resistance of electrical objects and equipment according to the CSN 331610 standard (for electrical appliances) with nominal voltage 100 V, 250 V and 500 V. It also allows to measure AC and DC voltage up to 550 V,
-
IC4 -
Holding Informtest
Precision digital resistance meter IS4 is intended for use in an upgraded version of the TEST-9110 installation quality control system and testing on-board cable networks. The IC4 module can also be successfully used in other control and measurement systems based on the open international VXI standard.
-
ERT1500 -
Summit
Resistance Range ; 20Ω/200Ω/2000Ω. Safety Standard ; IEC1010-1, IEC1557, CAT. 300V. Operating Temperature ; 0 to 40. Operating Humidity ; RH 70% MAX. Storage Temperature ; -10 to 50. Storage Humidity ; RH 80% MAX
-
WL MIDGET -
Walter G. Legge Company Inc.
WL MIDGET Surface Resistance Meter is an ultra-wide range, battery operated, portable instrument for measuring Surface Resistivity and Resistance to Ground of virtually any flat surface conforming to ASTM D-257 standard method by using recommended parallel bar sensing probe. Gives simple, repeatable measurements of conductive, static dissipative, and insulative surfaces. Ranging is automatic due to the use of high-speed OP-AMP Integrated circuits being linear, with changeover points +1/2 decade on a logarithmic scale. Repeatability equals + 5%.
-
Series 105 -
Pickering Electronics
• SoftCenter™ construction• Highest quality instrumentation grade switches• Encapsulated in a plastic package with internal mu-metal magnetic screen• Wide range of switch confi gurations -Form A, 1 Form B, 2 Form A, 1 Form C• Two pole relay requires the same board area as the single pole type• Dry and mercury wetted switches are available with the same pin configuration and footprint.• Many benefits compared to industry standard relays. Learn more here >.• Insulation resistance greater than 10E12 Ohms (1TOhms) for dry Form A devices• 5, 12 and 24 Volt coils are standard, with or without internal diode• 100% tested for dynamic contact resistance
-
GF6018A -
Beijing GFUVE Electronics Co.,Ltd.
The equipment is compliance with national verification regulation: JJG1242005 "Ammeter, voltmeter, power meter and resistance meter verification rules" and related national standards. 0.05 single-phase AC/DC standard source, can verify magnitude 0.2 and the following AC/DC voltmeter, ammeter, frequency meter, resistance meter. The source signals by using DSP and 16-bit high-speed analog-to-digital converters of controllable sine wave, the distorted wave signal source.The equipment comes with RS-232 interface, can be connected with PC to a semi-automatic verification system. It has precise interface and multi-functions including verification, storage and query.The equipment adopts color LCD screen, chart character display is clear, with high precision, stable and reliable, convenient operation and flexible characteristics.
-
MT-8001 -
Prokit's Industries Co., Ltd.
Recognized as the new industry standard, the MT-8001 butt set provides superior quality at an affordable price. With its high impedance monitor for data safe operation, technicians can clip onto a line in Monitor mode without disrupting existing traffic. Prokit's unsurpassed protection standards and durability assure the butt set will keep working even in the toughest environments. New weatherproofing provides enhanced resistance to severe weather conditions.Features
-
19036 -
Chroma Systems Solutions, Inc.
The industry’s first Wound Component Electrical Safety Test (EST) Analyzer that combines impulse winding, AC/DC hipot, insulation resistance and DC resistance test measurement functions. Chroma’s 19036 Wound Component EST Analyzer has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement with a maximum output of up to 40 channels. Capable of outputting and measuring AC100mA/DC 20mA, Chroma’s 19036 is suitable for testing to high power motor standards such as UL 1004-1.
-
CX-15 -
Shenzhen Chuangxin Instruments Co., Ltd.
The Impact Test Ball is a specially machined ball to test impact resistance according to IEC, CSA and UL Standards. It is made of chrome-plated-steel for durability, and is fitted with an eyelet to facilitate testing for pendulum applications. Eyelet is threaded to the ball to allow attachment of a handle or force gauge. Weights are closely controlled.
-
TF165 -
TESTEX Testing Equipment Systems Ltd.
Water Vapour Permeability Tester, to determine the resistance of textiles and textile composites (particularly action wear fabrics) to water vapour penetration. Water vapour permeability tester consists of 8 containers with water reservoirs; a standard permeable fabric cover, sample holder ring and precision drive system.
-
TESTEX Testing Equipment Systems Ltd.
Wyzenbeek Abrasion Tester,to determine the abrasion resistance of fabrics when rubbed against a standard abradent or a wire mesh screen with a backward and forward motion over a curved surface. Wyzenbeek Machine complies with ASTM D4157, etc. Please contact us for more information about Wyzenbeek methods.
-
ELMA Electronic, Inc.
All design enclosures and system cases are highly modular and flexible platforms. Kits are available for desktop, tower, 19’’ standard, portable and wall-mount applications. Some of our aluminum or plastic enclosures are available with EMC protection and meet RFI and other environmental requirements such as shock and vibration and water resistance.
-
T3PP350A -
Teledyne LeCroy
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
T3PP350 -
Teledyne LeCroy
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
PP006D -
Teledyne LeCroy
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.