Showing results: 466 - 480 of 919 items found.
-
RSICW-C -
Com-Ten Industries
With the RSIC data acquisition software, you can record hte measurements of your gauge Centor directly using MS Excel. It makes it easier to record results and ensure traceability and processing; these are the main advantages for using this simple yet powerful software.
-
Pickering Interfaces Ltd.
We offer simulation modules for Strain Gauge Simulation – used in mechanical systems to measure the tension or compression of structural components. These modules may also be used to simulate Wheatstone Bridge Pressure Sensors/Transducers. Simulation requires extremely fine setting resolution with high accuracy and temperature stability.
-
EX1629 -
AMETEK VTI Instruments
48-Channel High Performance Strain Gauge Measurement InstrumentSupports quarter-bridge (120, 350Ω or user defined), half-bridge or full-bridge24-bit ADCs, sampling rates up to 25 kSa/sBuilt in programmable differential excitation -8V to 8VBuilt in selectable bridge completionConfigure signal conditioning excitation and bridge completion on a per channel basisSimple, low-cost wiring using RJ-45 telecom connectorsSupports TEDS for easy transducer detection and setupRJ-45 input connector reduces setup cost and timeBuilt in self-calibration and shunt calibrationSupports voltage, ratiometric and linear measurements other than strain measurements.
-
MX 10x series -
E+H Metrology GmbH
The MX10x series measure thickness and thickness variation on silicon wafers. It has a resolution of 10 nanometers and can be adapted to different thickness ranges within a few seconds.
-
-
-
Check X-Line -
LAP GmbH
This process is unique on the market and was developed with our partner sema Systemtechnik. You receive a verifiable quality assurance of your rods or pipes in the current production. The modular design allows individual configurability and can be easily integrated into the existing system. Benefit from the competence and experience of two strong partners.
-
SPECTO series -
Heidenhain Corp.
*High system accuracy: ±1 µm*Very rugged design*Compact design for limited installation space*Various plunger actuation possibilities*Highly durable ball-bearing guide*Measuring range of up to 30 mm*Interfaces: 1 VPP, TTL*Protection rating of up to IP67
-
ACANTO series -
Heidenhain Corp.
*High system accuracy: ±2 µm / ±1 µm*Serial data transmission*Interface: EnDat 2.2*Protection rating of up to IP67*Compact design for limited installation space*Various plunger actuation possibilities
-
-
DV-4 Series -
Teledyne Hastings Instruments
Teledyne Hastings, manufacturer of the original DV-4, DV-5, and DV-6 thermocouple vacuum gauge tubes, produces vacuum measurement equipment with exceptional stability, accuracy, and reliability under the most demanding conditions.The Teledyne Hastings’ DV-4 Series thermocouple vacuum gauge tube/sensor can be paired with a variety of meters or controllers in the DV series to provide reliable, cost effective measurements in a variety of applications. The robust, easy to install gauge system translates a thermoelectric voltage to a vacuum pressure based on the density of the gas. The thermocouple gauge tube/sensor, DV-4, is fully compensated for temperature and rate of temperature change with no suspended weld to an external heater.The gauges are calibrated for nitrogen or air, but conversion factors for other gases are available from the factory. The thermocouple gauge or controller does not require recalibration when thermocouple gauge tubes are replaced further decreasing process down time. However, our DB-16D reference tube is available to confirm meter/controller performance. Installation accessories are also available from the factory to support your installation needs. One less thing to worry about, when performance matters! With a wide range of meter, fitting, relay and output options, the DV-4 Series can support a variety of applications.
-
HS160 -
Shenzhen Chuangxin Instruments Co., Ltd.
HS160 Wall measurement thickness gauge, wall thickness measuring equipment apply to measure the thickness of all kinds of material, through which the ultrasonic wave can propagate at a constant speed and can get reflection from the back. This instrument can be used for a variety of plate and all kinds of machining parts for accurate measurement. Another important function of this gauge is to monitor all kinds of pipelines and pressure vessels used in the production equipment, monitoring their degree of corroded thinning during the using process. It's widely used in petroleum, chemical industry, metallurgy, shipbuilding, aviation, aerospace and other fields.
-
FT150 Series -
Hitachi High-Technologies Corp.
The FT150 is a high-end fluorescent X-ray coating thickness gauge equipped with the polycapillary X-ray focusing optics and Vortex silicon drift detector. The improved X-ray detection efficiency enables high throughput and high precision measurement. Furthermore, new design to secure wide space around sample position gives exellent operability.
-
CNR EAR -
Com-Ten Industries
The Centor Easy R force gauges are designed to meet the production needs of its users. This group offers several features which are indispensable today for Quality Control, for example: ease of reading with its large backlit graphical display, RS232 output, memory of the last 100 values and ability to set thresholds with visual and sound alarms.
-
HR8833 -
HighReach Measuring & Controlling System Co.,Ltd
The HR8833 integrated pressure water level gauge is a three-parameter (water level, water temperature, conductivity) measurement product. It can be used with digital atmospheric pressure meter. It can be externally powered and self-powered by internal battery. It can be The product includes a water level sensor, a temperature sensor and a conductivity sensor, a built-in large-capacity non-volatile memory and a high-capacity long-life lithium battery, For three-parameter hydrological parameter measurement of surface water, groundwater and marine environment.