Showing results: 436 - 450 of 916 items found.
-
Becker Nachrichtentechnik GmbH
Modern receivers for broadcast have a large number of antenna inputs for the different radio bands. The devices of the FDMX series can be used to supply the antenna inputs with RF signals. The devices of the FDMX series splits a sum signal in frequency division multiplex into the individual broadcast bands and the L1 satellite navigation band (GNSS). Additionally, DC loads are provided for each antenna input to simulate active antennas. The presence of remote power supply is indicated by an LED on the units.
-
nRF52811 Series -
Raytac Corp
Raytac nRF52811 module employed MDBT42Q series design is a hardware pin to pin compatible to nRF52832 & nRF52810 solution with both Chip Antenna and PCB Antenna option for selection.
-
Doppler Systems Inc.
This assembly contains three sets of antennas, three RF summers, an antenna switch, a GPS and (optionally) a flux gate compass. The pod mounts to the roof with nylon straps, although it is recommended that it be bolted down for more permanent applications. Although this antenna is not stocked, we can provide them on relatively short notice. No minimums apply.
-
RAM-34 -
Array Solutions
The RAM-34 is a complete pre-amplifier system designed primarily for the low bands 160M thru 40M. It has inputs for four receive antennas and internal 3-pole bandpass filters for 160M, 80M and 40M. In addition to the pre-amplifier, it has a step attenuator that togetherwith the amplifier stage provides gains from -20 dB to +20 dB in 5 dB steps. This allows equalizing the signal levels between the antenna inputs. Gain settings are memorized for each antenna on each band. Different types of receive antennas have different signal levels and the gain memories eliminate the need to adjust the receiver or pre-amplifier when switching between the antennas.
-
Type 2-MQ -
National RF, Inc
The Type 2-MQ Portaquad is a high-gain, full size 2-meter quad antenna designed for portable operations. The mechanical design allows it to fold for stowage or transportation in a container. The container also acts as the antenna’s support base when the antenna is erected. After familiarity with the device is achieved, the antenna may be erected or collapsed in approximately one minute.
-
Antenna Research Associates
Antenna Research's UHF SATCOM tactical antennas are designed to be setup and operating quickly, some in as little as a few seconds. Our innovative designs include, pistol grip aim and communicate products, lightweight coat pocket versions with tripods and other mounting systems as well as well as ultra high gain larger antenna systems.
-
ALP620 -
Lectrosonics, Inc.
Skeletal remote antenna for decreased wind loading. The ALP Series antennas are a Log Periodic Dipole Array (LPDA) design that provides a useful directional pattern over a broad frequency bandwidth.
-
ALP500 -
Lectrosonics, Inc.
Standard remote antenna ideal for fixed applications. The ALP Series antennas are a Log Periodic Dipole Array (LPDA) design that provides a useful directional pattern over a broad frequency bandwidth.
-
Antenna Research Associates
Vehicular and Handheld antennas are available for communication, surveillance, signal DF, network repeaters and RF Jamming applications. A single omni or high gain directional ARA antenna may cover all cellular and/or Tetra communication bands and are compatible with all network technologies (GSM, CDMA, etc.). These wideband antennas replace the need for several single band antennas and are ideal for vehicular installations as well as handheld radio mounted applications. Permanent installations, quick deploy magnetic mounts or convenient pistol grips for radio location are available.
-
RF Explorer - 3G Combo -
Seeed Technology Inc.
This model includes a WSUB1G baseline unit plus an RFEMWSUB3G Expansion Module conveniently assembled and tested. It comes with two SMA connectors and two antennas,a nice Nagoya NA-773 wideband telescopic antenna for all Sub-GHz frequencies and a whip helical for 2.4GHz band. Additional, specific band antennas may be needed to cover efficiently some of the frequencies supported.
-
JYEBAO Co., Ltd.
Transmission lines for radio frequency (RF) signals traveling from one point in a system to another (e.g., PC board to PC board, PC board to antenna, equipment to antenna, equipment to equipment, etc.).
-
Spirent Federal Systems
The Spirent CRPA Test System is a development of Spirent’s GSS9000 Series platform for testing Controlled Reception Pattern Antenna (CRPA) systems with a separate RF output per antenna element. The CRPA Test System generates both GNSS and interference signals. Users can control multiple antenna elements. Null-steering and space/time adaptive CRPA testing are both supported by this comprehensive wavefront approach.
-
SX-SDMAC2 -
Silex Technology
The SX-SDMAC2 is a dual band IEEE802.11 a/b/g/n/ac WLAN and Bluetooth 5.0 BR/EDR/LE (Class1) module based on Qualcomm QCA9379-3 chipset. It supports 2x2 antenna configuration for applications that require higher performance. Silex has separated the Bluetooth antenna from the Wi-Fi by creating a third antenna port, allowing concurrent operation of Wi-Fi and Bluetooth further optimizing the Wi-Fi and Bluetooth performance.
-
Hitec RCD USA
An electronic device which produces radio waves with an antenna.
-
Raptor -
ImpulseRadar
The Raptor system covers a wide range of applications and can be configurated with 450 MHz or 800 MHz antennas. Raptor 3D Arrays are based on Real-Time sampling (RTS) technology and the unique antenna design is a milestone in the evolution of the GPR. A Raptor Antenna can be arranged in different ways, which allows for both standard and more advanced GPR measurements. These include common mid-point (CMP), wide-angle reflection and refraction (WARR) and Tomography.