Filter Results By:
Products
Applications
Manufacturers
-
product
Motor Test for Stepping Motors
*Stable measurement: Since it uses Prony braking, this model provides stable measurement unaffected by moments of inertia and no coupling loss. In addition, the resulting measurements allow data correlation via the traditional double-balance method.*Precision measurement method: This model’s judgment of synchronization loss achieves high stability using algorithms developed by Sugawara Laboratories. Measurement mode can be chosen based on step angle. For pull-in torque, startup can be measured consistently from the holding state. Allows measurement at 1-Hz resolution.*Broad measurement range: This model offers a range of seven available measurement heads, from 0.5 N to 50 N, allowing use for high-precision measurements. Through selection and use of pulleys, this model can also be used to measure small motors of 0.5 mN·m or less or 500 mN·m motors. Pulley diameters and other settings are easily configured using a personal computer running Windows®. Note: Any of the seven available heads may be attached to a single measurement component.*High-visibility measurement data: Motor characteristics are easily ascertained on automatically plotted performance graphs. Measurement data can be overlaid up to four times. In addition, the cursor can be used to read accurate values from measurement points. Hard copies of data displayed on-screen can be printed from a personal computer.*Can be controlled using standard personal computers: Allows control of measurement operations and display and storage of data from a standard personal computer running Windows®. Data is stored in CSV-format files for compatibility with other software applications.
-
product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
PCI / PMC / CompactPCI Test System
PCITS
The CPCI850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
product
Bus Analyzer / Exerciser
PCF850
The PCF850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
product
ARINC-429/717 XMC Interface For SBCs, VPX, VME, CPCI/PXI Systems
XMC-A429
The card design is based on the industry’s most advanced 32-bit ARINC FPGA protocol engine, AltaCore™, and a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET, LabVIEW, RTOS) architecture. This hardware and software package provides increased system performance and flexibility while reducing integration time.
-
product
Shared Memory Network PCI & PCIx Interface
PCI-SMN
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Compatible with PCI & PCIx Host System Slots - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
product
Temperature Measurement System
TMM-100
Thermal Engineering Associates, Inc.
The self contained TMM-100 module accepts diode, thermocouple and thermistor temperature sensors. The USB-connected instrument is supplied with Windows™ 7, 8 & 10 compatible software that provides for sensor measurement on a cyclic basis and for data logging of all measured values. LabVIEW™ Virtual Instrument (VI) drivers are available as an extra cost option for users that wish to incorporate the TMM-100 into an application-specific measurement environment.
-
product
SonarMite Processing Software
SonarW10
For most small boat applications the SonarW10 software provides a complete solution that lets the user combine Depth, Position and Tide data to produce a processed final survey data set. The software package is normally provided with the SonarMite echo sounder or the TidaLite tide gauge instruments as the download, editing and processing software. The program is designed for use on PCs running the Windows 7,8,10 or Tablet operating systems.
-
product
Frame Grabber Software
Alacron provides the complete software environment needed to get your machine vision or imaging application up and running quickly — from concept to working high performance systems. O/S environments supported include Windows 2000, WIN XP, Solaris, and Linux. Alacron's CODE DEVELOPMENT TOOLS provides all the facilities needed to develop and debug code for simple framegrabbers to multiprocessor applications.
-
product
Switchboard Instrument Wattmeter
ST-72 ST-96 KW
Standard Electric Works Co., Ltd
● Measuring Range:110V, 220V, 380V, 440V/1A, 5A● Accuracy: Class 1.5● Frequency:45-65 Hz● Test Voltage:2kV, 50-60 Hz● Pointer Length:ST-96 : 55mm ST-72 : 38mm● Composition:Glass window, ABS Resin frame and case, bakelite base mounting fitting included.● Color:Black base and frame, white scale plate and meter body.● Pointer:Stick shape in black color.● Transducer:External.
-
product
Optics Testing Systems
SHSInspect
SHSInspect instruments are widely used in R&D and production when performance, reliability and efficiency counts most. Based on the state-of-the-art wavefront sensor SHSLab, Optocraft offers measurement modules, turnkey instruments and automated tools for a great variety of applications in the field of optics and optical systems, such as:*objective lens testing*testing of optical elements and windows*surface shape measurement*inline measurement and automation
-
product
Micromachining Laser Workstation System
The enclosure design utilizes extruded aluminum framework construction. The light-tight design with removable interlocked covers, panels and doors provide easy and safe access.Internal lighting and laser safety window for visual inspection during the laser process are included with the ergonomic design. Complies with CDRH requirements as a Class 1 enclosure. The enclosure contains the complete laser head, laser beam delivery and motion system.
-
product
Data Loggers
Watlow Electric Manufacturing Company
Watlow offers a range of products for time-stamped data collection of critical process data, from Windows®-based software to embedded data loggers. Data loggers reduce labor, increase accuracy and help companies comply with regulatory requirements by automating data collection. These products make it easy to add data acquisition to existing processes, make data available to analytical software in spreadsheet compatible files, allow data to be grouped in user-defined batches and incorporate operator comments and other information into reports. Software solutions record data directly on a computer and data from embedded data loggers is transferred to a computer via universal serial bus (USB), secure digital (SD) card or flash drive.
-
product
HS1760/MIL-STD-1760E Network Interface Controller for PCI Express
PCIe-1760-NIC-FP
Avionics Interface Technologies
Configuration Variants available: PCIe-HS1760-NCNT: One NC Node and One NT Node, PCIe-HS1760-NCNC: Two NC Nodes, PCIe-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data - 75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
product
HS1760/MIL-STD-1760E XMC Network Interface Controller
XMC-1760-NIC-FP
Avionics Interface Technologies
Configuration Variants available: XMC-HS1760-NCNT: One NC Node and One NT Node, XMC-HS1760-NCNC: Two NC Nodes, XMC-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
product
MIL-STD-1553 Test & Simulation Interface for PCI
PCI-C1553
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - PCI & PCIx Compatible, 3.3V and 5V OperationApplication interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
WinSRS Software
The GHI Windows version of our powerful SRS module has been made even more powerful by the addition of new processing modes. These include: 1. Statistical SRS - This mode provides MEAN and Positive STANDARD DEVIATION plots which can be used when tailoring shock specifications based on environmental measurements. 2. Max-I-Max Envelope SRS - This module plots succeeding SRS's on one screen while at the same time plotting an 'envelope' that bounds all SRS's processed. 3. Overlay Plot - This mode allows overlaying plots of multiple SRS's. The user may plot Positive and Negative Max-I-Max spectra on the same screen. The foregoing are in addition to our traditional features
-
product
Talon 6 GHz RF/IF Sentinel Intelligent Signal Scanning Portable Recorder
Talon RTR 2623
- Search and capture system using Sentinel™ Intelligent Signal Scanner- Captures RF signals up to 6 GHz- Capture and scan bandwidths up to 40 MHz- 30 GHz/sec scan rate- Selectable threshold triggered or manual record modes- 16-bit A/D with 75 dB SNR & 87 dB SFDR- Built-in DDC with selectable decimation range from 2 to 65,536- Portable system measuring 16.0" W x 6.9" D x 13.0" H- Lightweight, just less than 30 pounds- Storage capabilities to 30 TB- RAID levels of 0, 5, and 6- Windows® workstation with Intel Core™ i7 processor
-
product
Automatic Voltage Regulator – 1.5kVA To 3kVA
SVR Pro
*Convenient Rackmount/Tower Design*UL Listed for 55°C Operation in Harsh Environments*True Sinewave Output*Superior Power Conditioning*Wide Input Voltage Window*Precision Output Voltage Regulation*Superior Brownout, Surge & Transient Protection*Frequency Converter Option*Battery Backup Capability Option*LCD Display with Advanced Monitoring for Easy Remote Management*RS-232C, USB & Optional SNMP/HTTP Agent
-
product
Automatic Voltage Regulator – 1kVA to 3kVA
SVR-PL™ Series
*Convenient Rackmount/Tower Design*UL Listed for High Temperature Operation -30°C to +65°C (-22°F to +149°F)*True Sinewave Output*Input Power Factor Correction*Wide Input Voltage Window*Precision Output Voltage Regulation*Extended Brownout, Plus Surge & Transient Protection*Frequency Converter Option*High Temperature LED Display*RS-232C, USB & Optional SNMP/HTTP Agent
-
product
HVR-LS Horizontal Vertical Flame Tester
HVR-LS/HVR-LSS
This equipment meets the requirements of ANSI/UL94, IEC60950-1, IEC695-2-2 and GB Standard. It is used to test the appliances and plastic materials parts of electrical equipment for the horizontal, vertical flammability test. The product tank shell is irony spray, and configured a transparent viewing window, the digital meter shows the burning time, afterflame time, afterglow time, this device has beautiful appearance, is easy to use and has reliable performance.
-
product
Performance Exams
Sturdy sheet steel housing with safety door and electrically driven base with built-on sample mold. The compaction takes place via a rolling segment with force / path-controlled drive device from above. The sample mold and the rolling segment are equipped with software controlled heating. The measurement of force and displacement is done by electronic sensors. The entire compaction process is controlled with Windows software and PC via preselected sequence programs.
-
product
USB 2.0 Protocol Analyzer
Mercury T2
The Mercury T2 is the industry's smallest, most affordable hardware-based USB 2.0 protocol analyzer that combines the defacto standard CATC Trace display with powerful analysis features. The pocket-sized Mercury T2 is bus powered and is controlled using any Windows PC. With comprehensive triggering, the Mercury T2 provides much of the same lab quality protocol analysis capabilities offered in Teledyne LeCroy's top-of-the-line USB analyzers.
-
product
Antenna Training and Measuring System
The complete Antenna Training and Measuring System includes a set of 1 GHz antennas, a set of 10 GHz antennas, an RF Generator, a receiving system, and the Data Acquisition and Management Software for Antennas (LVDAM-ANT), a user-friendly software operating under the Microsoft® Windows™ environment. The receiving system consists of a rotating Antenna Positioner linked to a Data Acquisition Interface connected to the USB port of a personal computer.
-
product
Distributed Test Manager
DTM
The Distributed Test Manager (DTM) is a Windows™ application which enables many different types of system level testing by simulating multiple devices in a system. DTM is a system level simulator that is unique compared to other Triangle MicroWorks tools which test the communications of a single device. DTM is a highly extensible tool with multiple options for configuring devices, creating test cases, and simulating data in the system.
-
product
Portable Testing Kit for Gulfstream Aircraft
ES-429TK-101
The ES-429TK-101 Portable Testing Kit (for Gulfstream aircraft) enables you to simulate Airspeed, Altitude and Radio Height values over an ARINC 429 bus. The ES-429TK-101 Portable Testing Kit consists of a DAS-429UNET/RT10, battery and the Exc429Tester application that runs on the host computer, a laptop or desktop PC running Windows. Using the ES- 429TK-101 Portable Testing Kit with a laptop provides a portable testing system.
-
product
Interface Adapter
DMX-10
DMX-10 is, all-in-one ready to use PCIEx to I2C/SPI/GPIO Interface adapter based on system with FPGA and 1x PCIEx PHY. DMX-10 converts PCIEx transactions into the I2C, SPI master or slave transactions and GPIO control functions. DMX-10 turns your PC running Windows, DOS, Linux, MacOS or any embedded OS with PCI support into comprehensive general purpose bus master or slave adapter.
-
product
LC Software
LabSolutions GPC Software
GPC software has been added to the LabSolutions lineup. This addition enables control and use of GC and HPLC instruments, including a GPC system, for analysis with the same interface, which simplifies the management of analytical instruments in your laboratory. With its easy-to-understand analysis windows, the GPC software provides the optimal environment for molecular weight distribution calculations, as well as qualitative and quantitative analysis via multiple detectors.
-
product
Fanless Embedded System With LGA1151 Socket 8th Gen Intel® Core™ & Celeron® Processor, Intel® H310, HDMI, DisplayPort, 6 USB, 2 COM And 8-CH DI/DO
eBOX640-521-FL
*LGA1151 socket 8th gen Intel® Core™ i7/i5/i3 & Celeron® processor (Coffee Lake)*Supports 2 COM, 6 USB and 8-CH DI/DO*Two 2.5" SATA drive bay*M.2 Key E 2230 for Wi-Fi*Front I/O connectivity design*12/19 to 24 VDC power input via DC-Jack*Flexible I/O window supported
-
product
Smart Control And Development Universal Software
The control software SCADUS (Smart Control And Development Universal Software) is based on Windows operating system. The test control software and test program development and debugging software are done in Delphi. It is designed for a wide base of customers. Each operator and engineer have a separate profile with all screens and software configurations. Online application development is also possible from another computer. The debugger and statistics are offered as standard accessories.